Grain Refinement in Dual-Phase Steels
Source abstract
Abstract
Deformation-induced ferrite transformation (DIFT) was applied in laboratory tests to produce fine-grained dual-phase (DP) steels. Four different chemistries were investigated, starting from a conventional DP 600 chemistry of 0.06 wt pct C-1.9 wt pct Mn-0.16 wt pct Mo and subsequently varying Nb and Mo additions. For all investigated steels, ultrafine ferrite (UFF) with a grain size of 1 to 2 μm can be obtained when a sufficient amount of deformation (e.g., a true strain of 0.6 or above in axisymmetric compression) is applied to an austenite microstructure with a grain size in the range of 10 to 20 μm at 25 °C to 50 °C above the austenite-to-ferrite transformation start temperature (Ar 3) characteristic for the given cooling condition. Rapid post-deformation cooling at rates of approximately 100 °C/s yields the desired UFF-martensite microstructure. Electron backscattered diffraction (EBSD) mapping reveals a high percentage (approximately 40 pct) of low-angle boundaries in these microstructures, except for the steel that is just microalloyed with Nb. The steel with the plain-carbon-base chemistry was subjected to hot torsion simulations of a hot strip rolling processing schedules that incorporate a DIFT pass after a conventional seven-stand finish mill schedule. Executing the DIFT pass at 650 °C to 675 °C produced an UFF microstructure, illustrating the potential for the design of novel thermomechanical processing paths to produce hot-rolled ultrafine DP steels.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Microstructure and mechanical properties · Metallurgy and Material Forming
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (40)
Show source-provided references
1. M. Militzer: Science, 2002, vol. 298, pp. 975–76.10.1126/science.1078210 ↗
2. K.T. Park, S.Y. Han, B.D. Ahn, D.H. Shin, Y.K. Lee, and K.K. Um: Scripta Mater., 2004, vol. 51, pp. 909–13.10.1016/j.scriptamat.2004.06.017 ↗
3. T. Morimoto, I. Chikushi, R. Kurahashi, and J. Yanagimoto: Proc. TMP 2004: 2nd Int. Conf. on Thermomechanical Processing of Steels, Stahleisen Verlag GmbH, Düsseldorf, Germany, 2004, pp. 415–22.
4. R. Ueji, N. Tsuji, Y. Minamino, and Y. Koizumi: Acta Mater., 2002, vol. 50, pp. 4177–89.10.1016/S1359-6454(02)00260-4 ↗
5. N. Tsuji, R. Ueji, Y. Minamino, and Y. Saito: Scripta Mater., 2002, vol. 46, pp. 305–10.10.1016/S1359-6462(01)01243-X ↗
6. L. Longfei, Y. Wangyue, and S. Zuqing: Metall. Mater. Trans. A, 2006, vol. 37A, pp. 609–19.10.1007/s11661-006-0033-y ↗
7. H. Dong, and X. Sun: Curr. Opin. Solid State Mater. Sci., 2005, vol. 9, 269–76.10.1016/j.cossms.2006.02.014 ↗
8. H. Beladi, G.L. Kelly, and P.D. Hodgson: Metall. Mater. Trans. A, 2007, vol. 38A, pp. 450–63.10.1007/s11661-006-9080-7 ↗
9. H. Yada, Y. Matsumura, and K. Nakazima; U.S. Patent No. 4466842, Aug. 21, 1984.
10. Y. Matsumura and H. Yada: Trans. ISIJ, 1987, vol. 27, pp. 492–98.10.2355/isijinternational1966.27.492 ↗
11. H. Yada, Y. Matsumura, and T. Senuma: Thermec ‘88-Int. Conf. on Physical Metallurgy of Thermomechanical Processing of Steels and Other Metals, I. Tamura, ed., The Iron and Steel Institute of Japan, Tokyo, 1988, pp. 200–07.
12. C.M. Li, H. Yada, and H. Yamagata: Scripta Mater., 1998, vol. 39, pp. 963–67.10.1016/S1359-6462(98)00239-5 ↗
13. M.R. Hickson, R.K. Gibbs, and P.D. Hodgson: ISIJ Int., 1999, vol. 39, pp. 1176–80.10.2355/isijinternational.39.1176 ↗
14. B. Eghbali and A. Abdollah-Zadeh: Scripta Mater., 2006, vol. 54, pp. 1205–09.10.1016/j.scriptamat.2005.11.026 ↗
15. J.Y. Cho, D.W. Suh, J.H. Kang, and H.C. Lee: in Ultrafine-Grained Materials II, Y.T. Zhu, T.G. Langdon, R.S. Mishra, S.L. Semiatin, M.J. Saran, and T.C. Lowe, eds., TMS, Warrendale, PA, 2002, pp. 259–65.10.1002/9781118804537.ch30 ↗
16. P.J. Hurley and P.D. Hodgson: Mater. Sci. Eng., A, 2001, vol. 302, pp. 206–14.10.1016/S0921-5093(00)01823-2 ↗
17. M.R. Hickson, P.J. Hurley, R.K. Gibbs, G.L. Kelly, and P.D. Hodgson: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 1019–26.10.1007/s11661-002-0203-5 ↗
18. P.D. Hodgson, M.R. Hickson, and R.K. Gibbs: Scripta Mater., 1999, vol. 40, pp. 1179–84.10.1016/S1359-6462(98)00411-4 ↗
19. P.J. Hurley, B.C. Muddle, and P.D. Hodgson: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 1507–17.10.1007/s11661-001-0238-z ↗
20. P.J. Hurley, P.D. Hodgson, and B.C. Muddle: Scripta Mater., 1999, vol. 40, pp. 433–38.10.1016/S1359-6462(98)00442-4 ↗
21. H. Beladi, G.L. Kelly, A. Shokouhi, and P.D. Hodgson: Mater. Sci. Eng., A, 2004, vol. A367, pp. 152–61.10.1016/j.msea.2003.09.095 ↗
22. S.C. Hong, S.H. Lim, K.J. Lee, and K.S. Lee: in Ultrafine-Grained Materials II, Y.T. Zhu, T.G. Langdon, R.S. Mishra, S.L. Semiatin, M.J. Saran, and T.C. Lowe, eds., TMS, Warrendale, PA, 2002, pp. 267–74.10.1002/9781118804537.ch31 ↗
23. J.K. Choi, D.H. Seo, J.S. Lee, K.K. Um, and W.Y. Choo: ISIJ Int., 2003, vol. 43, pp. 746–54.10.2355/isijinternational.43.746 ↗
24. S.C. Hong and K.S. Lee: Mater. Sci. Eng., A, 2002, vol. A323, pp. 148–59.10.1016/S0921-5093(01)01359-4 ↗
25. Z. Yang and R. Wang: ISIJ Int., 2003, vol. 43, pp. 761–66.10.2355/isijinternational.43.761 ↗
26. H. Beladi, G.L. Kelly, A. Shokouhi, and P.D. Hodgson: Mater. Sci. Eng., A, 2004, vol. A371, pp. 343–52.10.1016/j.msea.2003.12.024 ↗
27. M. Militzer, R. Pandi, and E.B. Hawbolt: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 1547–56.10.1007/BF02649814 ↗
28. D. Liu, F. Fazeli, and M. Militzer: ISIJ Int., 2007, vol. 47, pp. 1789–98.10.2355/isijinternational.47.1789 ↗
29. F.J. Humphreys: J. Mater. Sci., 2001, vol. 36, pp. 3833–54.10.1023/A:1017973432592 ↗
30. R. Lottey and M. Militzer: in Ultra-Fine Structured Steel, E. Essadiqi and J. Thomson, eds., Metallurgical Society of CIM, Montreal, 2004, pp. 87–98.
31. T. Gladman and F.B. Pickering: J. Iron Steel Inst., 1967, vol. 205, pp. 653–64.
32. “ASTM E384-99 Standard Test Method for Microindentation Hardness of Materials,” Annual Book of ASTM Standards, ASTM, West Conshohocken, PA, 2000, vol. 3.01, pp. 437–60.
33. S.C. Hong, S.H. Lim, H.S. Hong, K.J. Lee, D.H. Shin, and K.S. Lee: Mater. Sci. Eng., A, 2003, vol. A355, pp. 241–48.
34. M. Mazinani and W.J. Poole: Metall. Mater. Trans. A, 2007, vol. 38A, pp. 328–39.10.1007/s11661-006-9023-3 ↗
35. K. Mukherjee, S. Hazra, and M. Militzer: Proc. SAE 2006 World Congr., SAE International, SP-2035, Detroit, MI, 2006, pp. 81–86.
36. K. Mukherjee, S. Hazra, P. Petkov, and M. Militzer: Mater. Manuf. Processes, 2007, vol. 22, pp. 511–15.10.1080/10426910701236049 ↗
37. T. Morimoto, F. Yoshida, I. Chikushi, and J. Yanagimoto: ISIJ Int., 2007, vol. 47, pp. 1475–84.10.2355/isijinternational.47.1475 ↗
38. B. Hutchinson, L. Ryde, E. Lindh, and K. Tagashira: Mater. Sci. Eng., A, 1998, vol. A257, pp. 9–17.10.1016/S0921-5093(98)00820-X ↗
39. T. Waterschoot, L. Kestens, and B.C. De Cooman: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 1091–1102.10.1007/s11661-002-0211-5 ↗
40. S. Zäfferer, J. Ohlert, and W. Bleck: Acta Mater., 2004, vol. 52, pp. 2765–78.10.1016/j.actamat.2004.02.044 ↗