journal article·2008-10

Tensile Properties of Ni-Based Superalloy 720Li: Temperature and Strain Rate Effects

K. Gopinath, A.K. Gogia, S.V. Kamat, R. Balamuralikrishnan, U. Ramamurty

Publisher page

Abstract

Tensile properties, deformation, and fracture behavior of a wrought nickel-base superalloy 720Li have been studied in standard solutionized and two-stage-aged condition in the temperature range of 25 °C to 750 °C. Effect of strain rate on tensile behavior was assessed at 25 °C, 400 °C, and 750 °C at five strain rates that range between 10−5 s−1 and 10−1 s−1. The yield strength and ultimate tensile strength of the alloy remained unaffected by temperature until about 600 °C and 500 °C, respectively, typical of superalloys strengthened by fine and coherent intermetallic Ni3Al-based precipitates. The flow stress of the alloy was found to be insensitive to the strain rates studied at 25 °C and 400 °C. However, at 750 °C, the flow stresses showed strain rate sensitivity at strain rates 10−3 s−1, and at lower strain rates, tensile instability was seen to set in immediately after yielding. The alloy exhibited ductile dimple fracture at all the temperatures and strain rates studied. Microstructural investigations indicate that in regimes where flow stresses are insensitive to strain rate, deformation occurs through heterogeneous planar slip, whereas in strain rate sensitive regimes, thermally activated diffusion processes promote homogeneous deformation.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metallurgy and Material Forming · High Temperature Alloys and Creep · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (43)

Show source-provided references
1. S.J. Hessel, W. Voice, A.W. James, S.A. Blackham, C.J. Small, and M.R. Winstone: USP No. 6132527, 2000
2. R.J. Smith, G.J. Lewis, D.H. Yates: Aircraft Engineering and Aerospace Technol., 2001, vol. 73, pp. 138–4610.1108/00022660110694995 ↗
3. K. Steffens and H. Wilhelm: http://www.mtu.de/en/technologies/ engineering_news/ 11773.pdf
4. D. Helm and O. Roder: Superalloys, 2000, T.M. Pollock, R.D. Kissinger, R.R. Bowman, K.A. Green, M. McLean, S.L. Olson, and J.J. Schirra, eds., TMS, Warrendale, PA, 2000, pp. 487–9310.7449/2000/Superalloys_2000_487_493 ↗
5. D.J. Bryant and G. McIntosh: Superalloys, 1996, R.D. Kissinger, D.J. Deye, D.L. Anton, A.D. Cetel, M.V. Nathal, T.M. Pollock, and D.A. Woodford, eds., TMS, Warrendale, PA, 1996, pp. 713–2210.7449/1996/Superalloys_1996_713_722 ↗
6. M. Marchionni, G.A. Osinkolu, G. Onofrio: Int. J. Fatigue, 2002, vol. 24, pp. 1261–6710.1016/S0142-1123(02)00043-9 ↗
7. J. Albrecht: Mater. Sci. Eng., 1999, vol. A263, pp. 176–8610.1016/S0921-5093(98)01176-9 ↗
8. W.J. Evans, J.P. Jones, S. Williams: Int. J. Fatigue, 2005, vol. 27, pp. 1473–8410.1016/j.ijfatigue.2005.06.029 ↗
9. G. Onofrio, G.A. Osinkolu, M. Marchionni: Int. J. Fatigue, 2001, vol. 23, pp. 887–9510.1016/S0142-1123(01)00053-6 ↗
10. ASTM E 8M-04: Standard Test Methods for Tension Testing of Metallic Materials [Metric], Annual Book of ASTM Standards, Sec. 3, vol. 03.01, ASTM International, West Conshohocken, PA, 2005, pp. 86–109
11. ASTM E 21-03a: Standard Test Methods for Elevate Temperature Tension Tests of Metallic Materials, Annual Book of ASTM Standards, Sec. 3, vol. 03.01, ASTM International, West Conshohocken, PA, 2005, pp. 150–57
12. M.P. Jackson, R.C. Reed: Mater. Sci. Eng., 1999, vol. A259, pp. 85–9710.1016/S0921-5093(98)00867-3 ↗
13. J.M. Robinson, M.P. Shaw: Int. Mater. Rev., 1994, vol. 39 (3), pp. 113–2210.1179/imr.1994.39.3.113 ↗
14. G.E. Dieter: Mechanical Metallurgy, SI Metric Edition, McGraw-Hill Book Co., London, 1988, pp. 283–89
15. A. Ghosh: in ASM Handbook, vol. 14A, Metal Working: Bulk Forming, S.L. Semiatin, ed., ASM, Metals Park, OH, pp. 563–86
16. A. Kelly, R.B. Nicholson: Progr. Mater. Sci., 1963, vol. 10, pp. 151–39110.1016/0079-6425(63)90010-0 ↗
17. K. Luke, H. Mecking: The Inhomogenity of Plastic Deformation, ASM, Metals Park, OH, 1973, pp. 223–49
18. R.E. Reedhill and R. Abbaschian: Physical Metallurgy Principles, 3rd ed., Brooks/Cole Publication, 1994, pp. 181–83
19. D.C. Ludwigson: Metall. Trans., 1971, vol. 2, pp. 2825–2810.1007/BF02813258 ↗
20. M. Benyoucef, B. Décamps, A. Coujou, N. Clément: Phil. Mag. A, 1995, vol. 71, pp. 907–2310.1080/01418619508236228 ↗
21. W.R. Johnson, C.R. Barrett, W.D. Nix: Metall. Trans., 1972, vol. 3, pp. 963–6910.1007/BF02647673 ↗
22. F.E. Sczerzenie, S.O. Mancuso, P.W. Keefe, G.E. Maurer, and W.J. Boesch: Udimet Alloy 720, TR-88-002, Special Metals Corporation, New Hartford, NY, 1988
23. T.A. Parthasarathy, S.I. Rao, and D.M. Dimiduk: Superalloys, 2004, K.A. Green, T.M. Pollock, H. Hirada, T.E. Howson, R.C. Reed, J.J. Schirra, and S. Walston, eds., TMS, Warrendale, PA, 2004, pp. 887–9610.7449/2004/Superalloys_2004_887_896 ↗
24. P. Beardmore, R.G. Davies, T.L. Johnston: Trans. TMS-AIME, 1969, vol. 245, pp. 1537–45
25. D.L. Anton: in Intermetallic Compounds, vol. 2, Practice, J.H. Westbrook and R.L. Fleischer, eds., John Wiley & Sons Ltd., New York, NY, 1994, pp. 3–15
26. S.M. Copley, B.H. Kear: Trans. TMS-AIME, 1967, vol. 239, pp. 977–84
27. C.T. Liu and D.P. Pope: in Intermetallic Compounds, vol. 2, Practice, J.H. Westbrook and R.L. Fleischer, eds., John Wiley & Sons Ltd., New York, NY, 1994, pp. 17–51
28. P.H. Thornton, R.G. Davies, T.L. Johnston: Metall. Trans., 1970, vol. 1, pp. 207–1810.1007/BF02819263 ↗
29. S.M. Copley, B.H. Kear: Trans. TMS-AIME, 1967, vol. 239, pp. 984–92
30. G.R. Leverant, B.H. Kear: Metall. Trans., 1970, vol. 1, pp. 491–9810.1007/BF02811560 ↗
31. D. Mukherji, F. Jiao, W. Chen, R.P. Wahi: Acta Metall. Mater., 1991, vol. 39, pp. 1515–2410.1016/0956-7151(91)90237-U ↗
32. M.N. Menon, W.H. Reimann: Metall. Trans. A, 1975, vol. 6A, pp. 1075–85
33. S. Sinharoy, P. Virro-Nic, W.W. Milligan: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 2021–3210.1007/s11661-001-0014-0 ↗
34. G.R. Leverant, M. Gell, S.W. Hopkins: Mater. Sci. Eng., 1971, vol. 8, pp. 125–3310.1016/0025-5416(71)90050-4 ↗
35. G.R. Leverant, B.H. Kear: Metall. Trans., 1970, vol. 1, pp. 491–9810.1007/BF02811560 ↗
36. B.H. Kear, G.R. Leverant, J.M. Oblak: Trans. ASM, 1969, vol. 62, pp. 639–50
37. G.B. Viswanathan, P.M. Sarosi, D.H. Whitis, M.J. Mills: Mater. Sci. Eng. A, 2005, vols. 400–401, pp. 489–9510.1016/j.msea.2005.02.068 ↗
38. W.W. Milligan, S.D. Antolovich: Metall. Trans. A, 1991, vol. 22A, pp. 2309–1710.1007/BF02664997 ↗
39. S.S. Ezz, P.B. Hirsch: Phil. Mag. A, 1994, vol. 69, pp. 105–2710.1080/01418619408242213 ↗
40. E. Nembach, K. Suzuki, M. Ichhara, S. Takeuchi: Phil. Mag. A, 1985, vol. 51, pp. 607–1810.1080/01418618508237581 ↗
41. J.W. Martin: Micromechanisms in Particle Hardened Alloys, Cambridge University Press, New York, NY, 1980, pp. 99–114
42. M. Goto, D.M. Knowles: Eng. Fr. Mech., 1998, vol. 60, pp. 1–1810.1016/S0013-7944(98)00003-4 ↗
43. H.C. Rogers: Ductility, ASM, Metals Park, OH, 1968, pp. 31–61