Dendrite coherency of Al-Si-Cu alloys
Source abstract
Abstract
The dendrite coherency point of Al-Si-Cu alloys was determined by thermal analysis and rheological measurement methods by performing parallel measurements at two cooling rates for aluminum alloys across a wide range of silicon and copper contents. Contrary to previous findings, the two methods yield significantly different values for the fraction solid at the dendrite coherency point. This disparity is greatest for alloys of low solute concentration. The results from this study also contradict previously reported tl ends in the effect of cooling rate on the dendritic coherency point. Consideration of the results shows that thermal analysis is not a valid technique for the measurement of coherency. Analysis of the results from rheological testing indicates that silicon concentration has a dominant effect on grain size and dendritic morphology, independent of cooling rate and copper content, and thus is the factor that determines the fraction solid at dendrite coherency for Al-Si-Cu alloys.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Solidification and crystal growth phenomena · Aluminum Alloys Composites Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (31)
Show source-provided references
1. L. Bäckerud, E. Król, and J. Tamminen: Solidification Characteristics of Aluminium Alloys, Vol. 1: Wrought Alloys, SkanAluminium, Oslo, Norway, 1986.
2. L. Bäckerud, G. Chai, and J. Tamminen: Solidification Characteristics of Aluminium Alloys, Vol. 2: Foundry Alloys, AFS/SkanAluminium, Oslo, Norway, 1990.
3. L. Arnberg, L. Bäckerud, and G. Chai: Solidification Characteristics of Aluminium Alloys, Vol. 3: Dendrite Coherency, AFS, Des Plaines, IL, 1996.
4. J. Tamminen: Chemical Communications, Stockholm University, Stockholm, 1988, No. 2.
5. L. Arnberg, G. Chai, and L. Bäckerud: Mater. Sci. Eng., 1993, vol. A173, pp. 101–03.10.1016/0921-5093(93)90195-K ↗
6. G. Chai, L. Bäckerud, T. Rølland, and L. Arnberg: Metall. Mater. Trans. A, 1995, vol. 26A, pp, 965–70.10.1007/BF02649093 ↗
7. G. Chai, L. Bäckerud, and L. Arnberg: Z. Metallkd., 1995, vol. 86, pp. 54–59.
8. A.K. Dahle and L. Arnberg: Mater. Sci. Eng., 1997, vol. A225, pp. 38–46.10.1016/S0921-5093(96)10873-X ↗
9. A.K. Dahle and L. Arnberg: Acta Mater., 1997, vol. 45, pp. 547–59.10.1016/S1359-6454(96)00203-0 ↗
10. A.R.E. Singer and S.A. Cottrell: J. Inst. Met., 1947, vol. 73, pp. 33–54.
11. S.A. Metz and M.C. Flemings: AFS Trans., 1970, vol. 78, pp. 453–60.
12. D.B. Spencer, R. Mehrabian, and M.C. Flemings: Metall. Trans., 1972, vol. 3, pp. 1925–32.10.1007/BF02642580 ↗
13. R.J. Claxton: J. Met., 1975, Feb., pp. 14–16.10.1007/BF03355884 ↗
14. M. Suery and M.C. Flemings: Metall. Trans. A, 1982, vol. 13A, pp. 1809–19.10.1007/BF02647837 ↗
15. L. Bäckerud and B. Chalmers: Trans. AIME, 1969, vol. 245, pp. 309–18.
16. G. Chai: Chemical Communications, Stockholm University, Stockholm, 1994, No. 1.
17. A.K. Dahle and L. Arnberg: Proc. ICAA4, Atlanta, GA, 1994, pp. 91–98.
18. J. Campbell: AFS Cast Met. Res. J., 1969, vol. 5, pp. 1–8.
19. “Standard Methods for Determining Average Grain Size,” ASTM E112-95, ASTM, Philadelphia, PA, 1995.
20. N.L.M. Veldman, C.J. Davidson, A.K. Dahle, D.H. StJohn, and L. Arnberg: unpublished research.
21. J.E.C. Hutt, D.H. StJohn, L.M. Hogan, and A.K. Dahle: Mater. Sci. Technol., 1999, vol. 15, pp. 495–500.10.1179/026708399101506184 ↗
22. S. Gowri and F.H. Samuel: Metall. Mater. Trans. A, 1994, vol. 25A, pp. 437–48.10.1007/BF02647989 ↗
23. I. Dustin and W. Kurz: Z. Metall., 1986, vol. 77, pp. 265–73.
24. M. Rappaz and P.H. Thévoz: Acta. Metall., 1987, vol. 35, pp. 2929–33.10.1016/0001-6160(87)90292-6 ↗
25. B.P. Bardes and M.C. Flemings: AFS Trans., 1966, vol. 74, pp. 66–74.
26. P.C. Dann, J.A. Eady, and L.M. Hogan: J. Aust. Inst. Met., 1974, vol. 19 (2), pp. 140–47.
27. R. Fuoco and H. Goldenstein: Proc. 101st AFS Casting Congr., 1997, Seattle, WA, paper no. 97-091.
28. G.A. Edwards, G.K. Sigworth, C.H. Cáceres, D.H. StJohn, and J. Barresi: AFS Trans., 1997, vol. 105, pp. 809–18.
29. M.O. Otte, S.D. McDonald, J.A. Taylor, D.H. StJohn, and W. Schneider: AFS Trans., 1999, vol. 107, pp. 471–78.
30. J.A. Taylor, G.B. Schaffer, and D.H. StJohn: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 1643–62.10.1007/s11661-999-0101-1 ↗
31. A.K. Dahle and D.H. StJohn: Acta Mater., 1999, vol. 47, pp. 31–41.10.1016/S1359-6454(98)00342-5 ↗