journal article·2010-01

Effect of Friction Stir Processing on Microstructure and Mechanical Properties of a Cast-Magnesium–Rare Earth Alloy

T. A. Freeney, R. S. Mishra

Publisher page

Abstract

Single-pass friction stir processing (FSP) was used to increase the mechanical properties of a cast Mg-Zn-Zr-rare earth (RE) alloy, Elektron 21. A fine grain size was achieved through intense plastic deformation and the control of heat input during processing. The effects of processing and heat treatment on the mechanical and microstructural properties were evaluated. An aging treatment of 16 hours at 200 °C resulted in a 0.2 pct proof stress of 275 MPa in the FSP material, a 61 pct improvement over the cast + T6 condition.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloys Composites Properties · Magnesium Alloys: Properties and Applications

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (89)

Show source-provided references
1. J. Aragones and K. Goundan: Development of the 2006 Corvette Z06 Structural Cast Magnesium Crossmember, SAE International, 2005.10.4271/2005-01-0340 ↗
2. A. Wendt, K. Weiss, A. Ben-Dov, M. Bamberger, and B. Bronfin: Magnesium Technology, TMS, Warrendale, PA, 2005, pp. 269–73.
3. S. Schumann and H. Friedrich: Mater. Sci. Forum, 2003, vol. 51, pp. 419–22.
4. D.A. Kramer: Magnesium: Its Alloys and Compounds, U.S. Geological Survey Open-File Report 01-341, http://pubs.usgs.gov/of/2001/of01-341/10.3133/ofr01341 ↗
5. G. Cole: Proc. 54th Int. Magnesium Association, Toronto, ON, Canada, 1997.
6. H. Friedrich and S. Schumann: Proc. 2nd Israeli Int. Conf. on Magnesium Science and Technology, Dead Sea, Israel, 2000, pp. 9–26.
7. N. Li, R. Osbourne, B. Cox, and D. Penrod: Magnesium Engine Cradle—The USCAR Structural Cast Magnesium Development Project, SAE International, 2005.10.4271/2005-01-0337 ↗
8. R.S. Mishra and Z.Y. Ma: Mater. Sci. Eng., R, 2005, vol. 50, pp. 1–78.10.1016/j.mser.2005.07.001 ↗
9. R.S. Mishra, M.W. Mahoney, S.X. McFadden, N.A. Mara, and A.K. Mukherjee: Scripta Mater., 2000, vol. 42, p. 163.10.1016/S1359-6462(99)00329-2 ↗
10. R.S. Mishra and M.W. Mahoney: Mater. Sci. Forum, 2001, vols. 357–359, p. 507.10.4028/www.scientific.net/MSF.357-359.507 ↗
11. W.M. Thomas, E.D. Nicholas, J.C. Needham, M.G. Murch, P. Templesmith, and C.J. Dawes: G.B. Patent Application 9125978.8, 1991.
12. Z.Y. Ma, S.R. Sharma, and R.S. Mishra: Scripta Mater., 2006, vol. 54, pp. 1623–26.10.1016/j.scriptamat.2006.01.010 ↗
13. M.L. Santella. T. Engstrom, D. Storjohann, and T.Y. Pan: Scripta Mater., 2005, vol. 53, p. 201.10.1016/j.scriptamat.2005.03.040 ↗
14. Z.Y. Ma, S.R. Sharma, R.S. Mishra, and M.W. Mahoney: Mater. Sci. Forum, 2003, vols. 426–432, p. 2891.10.4028/www.scientific.net/MSF.426-432.2891 ↗
15. Z.Y. Ma, S.R. Sharma, and R.S. Mishra: Mater. Sci. Eng., A, 2006, vol. 433, pp. 269–78.10.1016/j.msea.2006.06.099 ↗
16. M. Santella, A. Frederick, C. Degen, and T.-Y. Pan: JOM, 2006, vol. 58 (5), pp. 56–61.10.1007/s11837-006-0025-9 ↗
17. R. Johnson: Mater. Sci. Forum, 2003, vols. 419–422, p. 365.10.4028/www.scientific.net/MSF.419-422.365 ↗
18. W.B. Lee, Y.M. Yeon, and S.B. Jung: Mater. Sci. Technol., 2003, vol. 19, p. 785.10.1179/026708303225001867 ↗
19. G. Kohn, S. Antonsson, and A. Munitz: Automotive Alloys 1999, TMS, Warrendale, PA, 2000, pp. 285–92.
20. P. Lyon: Magnesium Technology, TMS, Warrendale, PA, 2004, pp. 311–315.
21. M. Tsujikawa, S.W. Chung, M. Tanaka, Y. Takigawa, S. Oki, and K. Higashi: Mater. Trans., 2005, vol. 46 (12), pp. 3081–84.10.2320/matertrans.46.3081 ↗
22. T.A. Freeney, R.S. Mishra, G.J. Grant, and R. Verma: Friction Stir Welding and Processing IV, TMS, Warrendale, PA, 2007.
23. B.J. Coultes, J.T. Wood, G. Wang, and R. Berkmortel: Magnesium Technology, TMS, Warrendale, PA, 2003, pp. 45–50.
24. Magnesium Elektron, Manchester, United Kingdom, Datasheet 440: www.melpure.com
25. ASM Specialty Handbook: Magnesium and Magnesium Alloys, M.M. Avedesian and H. Baker, eds., ASM INTERNATIONAL, Materials Park, OH, 1999.
26. B. Smola, I. Stulikova, F. von Buch, and B.L. Mordike: Mater. Sci. Eng., A, 2002, vol. 324, pp. 113–17.10.1016/S0921-5093(01)01291-6 ↗
27. Y. Negishi, T. Nishimura, M. Kiryuu, S. Kamado, Y. Kojima, and R. Ninomiya: J. Jpn. Inst. Light Met., 1995, vol. 45, pp. 57–63.10.2464/jilm.45.57 ↗
28. J.F. Nie and B.C. Muddle: Acta Mater., 2000, vol. 48, pp. 1691–1703.10.1016/S1359-6454(00)00013-6 ↗
29. D.H. St. John, M. Qian, M.A. Easton, P. Cao, and Z. Hildebrand: Metall. Mater. Trans. A, 2005, vol. 36A, p. 1669.10.1007/s11661-005-0030-6 ↗
30. P. Cao, M. Qian, and D.H. St. John: Scripta Mater., 2004, vol. 51, pp. 125–29.10.1016/j.scriptamat.2004.03.039 ↗
31. E.F. Emley: Principles of Magnesium Technology, 1st ed., Pergamon Press, Oxford, United Kingdom, 1966.
32. M. Qian, D. Graham, L. Zheng, D.H. St John, and M.T. Frost: Mater. Sci. Technol., 2003, vol. 19, pp. 156–62.10.1179/026708303225010849 ↗
33. M. Qian, D.H. StJohn, and M.T. Frost: Scripta Mater., 2002, vol. 46, pp. 649–54.10.1016/S1359-6462(02)00046-5 ↗
34. L.L. Rohklin: in Magnesium Alloys Containing RE Metals: Structure and Properties, J.N. Fridlyander and D.G. Eskin, eds., Taylor and Francis, 2003.
35. E.D. Levine, W.F. Sheely, and R.R. Nash: Trans. AIME, 1959, vol. 215, p. 253.
36. C.R. Brooks: Heat Treatment Structure and Properties of Nonferrous Alloys, ASM, Materials Park, OH, 1982, pp. 255–56.
37. S. Zhang: Acta Metall. Sinica, 1989, vol. 3A, pp. 110–15 (English edition).
38. S. Cohen, G.R. Goren-Muginstein, S. Avraham, G. Dehm, and M Bamberger: Magnesium Technology, TMS, Warrendale, PA, 2004, pp. 301–05.
39. J.C. Rao, M. Song, K. Furuya, S. Yoshimoto, M. Yamasaki, and Y. Kawamura: J. Mater. Sci., 2006, vol. 41, pp. 2573–76.10.1007/s10853-006-7782-2 ↗
40. Y. Kawamura, K. Hayashi, A. Inoue, and T. Masumoto: Metall. Mater. Trans. A, 1995, vol. 26A, p. 1705.
41. A. Inoue, Y. Kawamura, Y. Matsushita, K. Hayashi, and J. Koike: J. Mater. Res., 2001, vol. 16, p. 1894.10.1557/JMR.2001.0260 ↗
42. E. Abe, Y. Kawamura, K. Hayashi, and A. Inoue: Acta Mater., 2002, vol. 50, p. 3845.10.1016/S1359-6454(02)00191-X ↗
43. A. Inoue, Y. Matsushita, Y. Kawamura, K. Amiya, K. Hayashi, and J. Koike: Metall. Mater. Trans. A, 2002, vol. 33A, p. 580.
44. D.H. Ping, K. Hono, Y. Kawamura, and A. Inoue: Philos. Mag. Lett., 2002, vol. 82, p. 543.10.1080/0950083021000018652 ↗
45. Z. Hildebrand, M. Qian, D. St. John, and M. Frost: Magnesium Technology, TMS, Warrendale, PA, 2004, pp. 241–45.
46. K. Löhberg and G. Schmidt: Giessereiforschung, 1975, vol. 27 (3), pp. 75–82.
47. S. Bhan and A. Lal: J. Phase Equilib., 1993, vol. 14, pp. 634–37.10.1007/BF02669156 ↗
48. R. Arroyave, A. van de Walle, and Z.-K. Liu: Acta Mater., 2006, vol. 54, pp. 473–82.10.1016/j.actamat.2005.09.018 ↗
49. N.F. Lashko and G.I. Morozova: Sov. Phys.-Cryst., 1969, vol. 14, pp. 143–45.
50. T. Chun-Hu, Z. Shao-Qing, and L. Li-Qi: J. Rare Earths, 1991, vol. 9 (2).
51. G.I. Morozova, V.V. Tikhonova, and N. F. Lashko: Met. Sci. Heat Treat. (Russia), 1978, vol. 20, pp. 657–60.10.1007/BF00780803 ↗
52. J. Hasegawa, S. Takeuchi, and A.P. Tsai: Philos. Mag. Lett., 2005, vol. 85 (6), pp. 289–97.10.1080/14786430500155536 ↗
53. P. Lyon, T. Wilks, and I. Syed: Magnesium Technology, TMS, Warrendale, PA, 2005, pp. 303–08.
54. M.E.Drits, L.L. Rohklin, E.M. Padeezhnova, I.I. Gurez, N.V. Miklina, T.V. Dobatkina, and A.A. Oreshkina: Magnesium Alloys with Yttrium, Nauka, Moscow, 1979 (in Russian).
55. M.E. Drits, Z.A. Sviderskaya, and L.L. Rokhlin: Izv. Vyss. Uchebn. Zaved. Tsvetn. Metall., 1962, vol. 3, pp. 117–21 (in Russian).
56. M.E. Drits, Z.A. Sviderskaya, and L.L. Rokhlin: Metallurgiya, Metallovedenie I Fiziko-Khimicheskie Metody Issledovaniya, Russian Academy of Science, Moscow, 1963, vol. 14, pp. 120–29 (in Russian).
57. P. Frankel: Elektron 21 Evaluation—Materials Science Investigation, Magnesium Elektron, Manchester, United Kingdom, 2003.
58. L. Gill, G.W. Lorimer, and P. Lyon: DGM Conf. on Microstructure and Property Relationships of Mg-RE-Zn-Zr Alloys, Germany, 2003.10.1002/3527603565.ch66 ↗
59. G. Bruzzone, M.L. Fornasini, and F. Merlo: JLCM, 1920, vol. 22, pp. 253–64.10.1016/0022-5088(70)90074-3 ↗
60. P. Manfrinetti and K.A. Gschneidner, Jr.: JLCM, 1986, vol. 123, pp. 267–75.10.1016/0022-5088(86)90135-9 ↗
61. H. Okamato: J. Phase Equilib., 1991, vol. 12, pp. 249–50.10.1007/BF02645728 ↗
62. S. Delfino, A. Saccone, and R. Ferro: Metall. Trans. A, 1990, vol. 21A, pp. 2109–14.10.1007/BF02647869 ↗
63. K.A. Gschneidner, Jr. and F.W. Calderwood: Bull. Alloy Phase Diagrams, 1982, vol. 3 (3), pp. 351–53.10.1007/BF02869309 ↗
64. P.J. Apps, H. Karimzadeh, J.F. King, and G.W. Lorimer: Scripta Mater., 2003, vol. 48, pp. 475–81.10.1016/S1359-6462(02)00509-2 ↗
65. Y.M. Riddle, L.P. Barber, and M.M. Makhlouf: Magnesium Technology, TMS, Warrendale, PA, 2004, pp. 203–08.
66. G.W. Lorimer, G. Cliff, P.E. Champness, C. Dickinson, F. Hasan, and P.B. Kenway: Analytical Electron Microscopy, San Francisco Press, 1984, p. 153.
67. G.W. Lorimer: Proc. Magnesium Technology, Institute of Metals, London, 1986, p. 47.
68. P. Vostry, I. Stulokova, B. Smola, M. Cieslar, and B.L. Mordike: Z. Metallkd., 1988, vol. 79, p. 340.
69. B. Smola and B.L. Mordike: 10th Eur. Crystallographic Meeting, Collected Abstracts, IUCr, Wroclaw, Poland, 1986, p. 411.
70. S. Kamado, Y. Kojima, S. Tanike, I. Seki, and S. Hama: in Mg Alloys and Their Applications, B.L. Mordike and K.U. Kainer, eds., Werkstoff-Informationsgesellschft, Frankfurt, Germany, 1998, p. 229.
71. J.F. Nie and B.C. Muddle: in Mg Alloys and Their Applications, B.L. Mordike and K.U. Kainer, eds., Werkstoff-Informationsgesellschft, Frankfurt, Germany, 1998, p. 229.
72. K.V. Jata and S.L. Semiatin: Scripta Mater., 2000, vol. 43, p. 743.10.1016/S1359-6462(00)00480-2 ↗
73. P. Heurtier, C. Desrayaud, and F. Montheillet: Mater. Sci. Forum, 2002, vols. 396–402, p. 1537.10.4028/www.scientific.net/MSF.396-402.1537 ↗
74. X. Xu and S. Deng: Proc. 4th Int. FSW Symp., TWI, Cambridge, United Kingdom, 2003 (CD-ROM).
75. W.B. Lee, Y.M. Yeon, and S.B. Jung: Mater. Sci. Technol., 2003, vol. 19, p. 785.10.1179/026708303225001867 ↗
76. S.H.C. Park, Y.S. Sato, and H. Kokawa: Proc. 6th Int. Conf. on Trends in Welding Research, S.A. David, T. DebRoy, J.C. Lippold, H.B. Smartt, and J.M. Vitek, eds., ASM INTERNATIONAL, Materials Park, OH, 2003, p. 267.
77. K.V. Jata and S.L. Semiatin: Scripta Mater., 2000, vol. 43, p. 743.10.1016/S1359-6462(00)00480-2 ↗
78. J.-Q. Su, T.W. Nelson, R. Mishra, and M. Mahoney: Acta Mater., 2003, vol. 51, p. 713.10.1016/S1359-6454(02)00449-4 ↗
79. K.V. Jata, K.K. Sankaran, and J.J. Rushau: Metall. Mater. Trans. A, 2000, vol. 31A, p. 2181.10.1007/s11661-000-0136-9 ↗
80. Y.S. Sato, M. Urata, and H. Kokawa: Metall. Mater. Trans. A, 2002, vol. 33A, p. 625.10.1007/s11661-002-0124-3 ↗
81. J.-Q. Su, T.W. Nelson, and C.J. Sterling: Mater. Sci. Eng., A, 2005, vol. 405, pp. 277–86.10.1016/j.msea.2005.06.009 ↗
82. P.B. Pragnell and C.P. Heason: Acta. Mater., 2005, vol. 53, pp. 3179–92.10.1016/j.actamat.2005.03.044 ↗
83. K.A.A. Hassan, B.P. Wynne, and P.B. Pragnell: 4th Int. Symp. on FSW, TWI, Cambridge, United Kingdom, 2003 (CD- ROM).
84. W. Blum, Q. Zhu, R. Merkel, and H.J. McQueen: Mater. Sci. Eng., A, 1996, vol. 205, p. 23.10.1016/0921-5093(95)09990-5 ↗
85. K.N. Krishnan: Mater. Sci. Eng., A, 2002, vol. 327, pp. 246–51.10.1016/S0921-5093(01)01474-5 ↗
86. H. Larsson, L. Karlsson, S. Stoltz, and E.-L. Bergqvist: 2nd Int. Conf. on Friction Stir Welds, Gothenburg, Sweden, 2000.
87. Z.Y. Ma, S.R. Sharma, and R.S. Mishra: Metall. Mater. Trans. A, 2006, vol. 37A, pp. 3323–36.10.1007/BF02586167 ↗
88. W.-J. Kim, S.W. Chung, C.S. Chung, and D. Kum: Acta Mater., 2001, vol. 49, pp. 3337–45.10.1016/S1359-6454(01)00008-8 ↗
89. G. Riontino, D. Lussana, and M. Massazza: J. Mater. Sci., 2006, vol. 41, pp. 3167–69.10.1007/s10853-006-6375-4 ↗