journal article·2010-08

Effect of Heat Input Conditions on Microstructure and Mechanical Properties of Friction-Stir-Welded Pure Copper

P. Xue, G.M. Xie, B.L. Xiao, Z.Y. Ma, L. Geng

Publisher page

Abstract

Defect-free friction stir welds of 5-mm-thick pure copper plates were produced in relatively low heat input conditions. The characteristics of the microstructure and mechanical properties of the welded joints were investigated. The stir zone (SZ) exhibited equiaxed recrystallized grains, whose size decreased as the heat input was decreased. The percentage of high-angle grain boundaries (grain boundary misorientation angle >15 deg) in the SZ was quite high (90.2 to 94.5 pct) and increased as the heat input was increased. When the heat input was decreased, the percentage of the twin boundaries (TBs) dropped, and the number of the twin lamellas was reduced. Under a very low heat input condition, the typical characteristics of thermomechanically affected zone (TMAZ) were discernible; however, the TMAZ was characterized by a recrystallized grain structure at higher heat input conditions. The grains in the heat-affected zone (HAZ) were slightly coarsened compared to those in the parent material (PM), but the grain size varied a little under different parameters. The hardness of the SZ increased as the heat input was increased, and the lowest hardness appeared at the HAZs where the welds failed. The ultimate tensile strength (UTS) was similar to that of the PM under various heat input conditions, but the yield strength (YS) and elongation were lower. The YS increased as the lowest hardness value increased, and the elongation decreased due to the enhanced strain localization.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloys Composites Properties · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (27)

Show source-provided references
1. Chinese Welding Society: Welding Handbook, 2nd ed., China Machine Press, Beijing, 2001, vol. 2, pp. 608–43.
2. S.A. Fabritsiev, A.S. Pokrovsky, M. Nakamichi, and H. Kawamura: J. Nucl. Mater., 1998, vol. 2030, pp. 258–63.
3. T.D. Uzunov, S.P. Stojanov, and S.I. Lambov: Vacuum, 1999, vol. 52, pp. 365–68.10.1016/S0042-207X(98)00310-8 ↗
4. W.M. Thomas, E.D. Nicholas, J.C. Needham, M.G. Murch, P. Templesmith, and C.J. Dawes: G.B. Patent Application No. 9125978.8, Dec. 1991.
5. R.S. Mishra and Z.Y. Ma: Mater. Sci. Eng. R, 2005, vol. 50, pp. 1–78.10.1016/j.mser.2005.07.001 ↗
6. C.G. Andersson and R.E. Andrews: Proc. 1st Int. Symp. on Friction Stir Welding, Thousand Oaks, CA, 1999.
7. C.G. Andersson, R.E. Andrews, B.G.I. Dance, M.J. Russell, E.J. Olden, and R.M. Sanderson: Proc. 2nd Int. Symp. on Friction Stir Welding, Gothenburg, Sweden, 2000.
8. K. Okamoto, M. Doi, S. Hirano, K. Aota, H. Okamura, Y. Aono, and T.C. Ping: Proc. 3rd Int. Symp. on Friction Stir Welding, Kobe, Japan, 2001.
9. W.B. Lee and S.B. Jung: Mater. Lett., 2004, vol. 58, pp. 1041–46.10.1016/j.matlet.2003.08.014 ↗
10. T. Hautala and T. Tiainen: Proc. 6th Int. Conf. on Trends in Welding Research, Pine Mountain, GA, 2003, ASM INTERNATIONAL, Materials Park, OH, 2003, pp. 324–28.
11. G.M. Xie, Z.Y. Ma, and L. Geng: Scripta Mater., 2007, vol. 57, pp. 73–76.10.1016/j.scriptamat.2007.03.048 ↗
12. H.J. Liu, J.J. Shen, Y.X. Huang, L.Y. Kuang, C. Liu, and C. Li: Sci. Technol. Weld. Join., 2009, vol. 14, pp. 577–83.10.1179/136217109X456951 ↗
13. T. Sakthivel and J. Mukhopadhyay: J. Mater. Sci., 2007, vol. 42, pp. 8126–29.10.1007/s10853-007-1666-y ↗
14. T.R. McNelley, S. Swaminathan, and J.Q. Su: Scripta Mater., 2008, vol. 58, pp. 349–54.10.1016/j.scriptamat.2007.09.064 ↗
15. A.P. Reynolds: Mater. Sci. Forum, 2007, vols. 539–543, pp. 207–14.10.4028/www.scientific.net/MSF.539-543.207 ↗
16. A.P. Reynolds, W. Tang, Z. Khandkar, J.A. Khan, and K. Lindner: Sci. Technol. Weld. Join., 2005, vol. 10, pp. 190–99.10.1179/174329305X37024 ↗
17. Y.S. Sato, M. Urata, and H. Kokawa: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 625–35.10.1007/s11661-002-0124-3 ↗
18. Z.Y. Ma, R.S. Mishra, M.W. Mahoney, and R. Grimes: Metall. Mater. Trans. A, 2005, vol. 36A, pp. 1447–58.10.1007/s11661-005-0237-6 ↗
19. L. Liu, H. Nakayama, S. Fukumoto, A. Yamamoto, and H. Tsubakino: Mater. Trans. JIM, 2004, vol. 8, pp. 2665–68.10.2320/matertrans.45.2665 ↗
20. R.S. Mishra and M.W. Mahoney: Mater. Sci. Forum, 2001, vols. 357–359, pp. 507–12.10.4028/www.scientific.net/MSF.357-359.507 ↗
21. A.F. Norman, I. Brough, and P.B. Prangnell: Mater. Sci. Forum, 2000, vols. 331–337, pp. 1713–18.10.4028/www.scientific.net/MSF.331-337.1713 ↗
22. F.C. Liu, Z.Y. Ma, and L.Q. Chen: Scripta Mater., 2009, vol. 60, pp. 968–71.10.1016/j.scriptamat.2009.02.021 ↗
23. A. Vinogradov, T. Suzuki, S. Hashimoto, K. Kitagawa, A. Kuznetsov, and S. Dobatkin: Mater. Sci. Forum, 2006, vols. 503–504, pp. 971–76.10.4028/www.scientific.net/MSF.503-504.971 ↗
24. Y.S. Sato, H. Kokawa, M. Enomoto, and S. Jogan: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 2429–37.10.1007/s11661-999-0251-1 ↗
25. F.J. Humphreys and M. Hatherly: Recrystallization and Related Annealing Phenomena, 2nd ed., Elsevier Ltd., New York, NY, 2004, pp. 261–67.
26. L.E. Murr: Interfacial Phenomena in Metals and Alloys, Addison-Wesley, Reading, MA, 1975, p. 131.
27. Y.S. Sato and H. Kokawa: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 3023–31.10.1007/s11661-001-0177-8 ↗