Transient Heat and Material Flow Modeling of Friction Stir Processing of Magnesium Alloy using Threaded Tool
Source abstract
Abstract
A three-dimensional transient computational fluid dynamics (CFD) model was developed to investigate the material flow and heat transfer during friction stir processing (FSP) in an AZ31B magnesium alloy. The material was assumed to be a non-Newtonian viscoplastic fluid, and the Zener-Hollomon parameter was used to describe the dependence of material viscosity on temperature and strain rate. The material constants used in the constitutive equation were determined experimentally from compression tests of the AZ31B Mg alloy under a wide range of strain rates and temperatures. A dynamic mesh method, combining both Lagrangian and Eulerian formulations, was used to capture the material flow induced by the movement of the threaded tool pin. Massless inert particles were embedded in the simulation domain to track the detailed history of material flow. The actual FSP was also carried out on a wrought Mg plate where temperature profiles were recorded by embedding thermocouples. The predicted transient temperature history was found to be consistent with that measured during FSP. Finally, the influence of the thread on the simulated results of thermal history and material flow was studied by comparing two models: one with threaded pin and the other with smooth pin surface.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloys Composites Properties · Metal Forming Simulation Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (48)
Show source-provided references
1. H. Watanabe, T. Mukai, M. Kohzu, S. Tanabe, and K. Higashi: Acta Mater., 1999, vol. 47, pp. 3753-58.10.1016/S1359-6454(99)00253-0 ↗
2. C.I. Chang, C.J. Lee, and J.C. Huang: Scripta Mater., 2004, vol. 51, pp. 509-14.10.1016/j.scriptamat.2004.05.043 ↗
3. N.V.R. Kumar, J.J. Blandin, C. Desrayaud, F. Montheillet, and M. Suery: Mater. Sci. Eng. A-Struct., 2003, vol. 359, pp. 150-57.10.1016/S0921-5093(03)00334-4 ↗
4. V.N. Chuvil’deev, A.V. Schavleva, M.Y. Gryaznov, and A.V. Nokhrin: Dokl. Phys., 2006, vol. 51, pp. 500-04.10.1134/S1028335806090114 ↗
5. Y.S. Sato, S.H.C. Park, A. Matsunaga, A. Honda, and H. Kokawa: J. Mater. Sci., 2005, vol. 40, pp. 637-42.10.1007/s10853-005-6301-1 ↗
6. P. Cavaliere and P.P. De Marco: Mater. Sci. Eng. A-Struct., 2007, vol. 462, pp. 393-97.10.1016/j.msea.2006.04.150 ↗
7. C.I. Chang, X.H. Du, and J.C. Huang: Scripta Mater., 2007, vol. 57, pp. 209-12.10.1016/j.scriptamat.2007.04.007 ↗
8. R.S. Mishra and Z.Y. Ma: Mater. Sci. Eng. R, 2005, vol. 50, pp. 1-78.10.1016/j.mser.2005.07.001 ↗
9. Z. Yu, H. Choo, Z. Feng, and S. Vogel: Scripta Mater., 2010, vol. 63, pp. 1112-15.10.1016/j.scriptamat.2010.08.016 ↗
10. W. Woo, Z. Feng, X.L. Wang, D.W. Brown, B. Clausen, K. An, H. Choo, C.R. Hubbard, and S.A. David: Sci. Technol. Weld Joi., 2007, vol. 12, pp. 298-303.10.1179/174329307X197548 ↗
11. O. Frigaard, O. Grong, and O.T. Midling: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 1189-1200.10.1007/s11661-001-0128-4 ↗
12. A. Bastier, M.H. Maitournam, K.D. Van, and F. Roger: Sci. Technol. Weld Joi., 2006, vol. 11, pp. 278-88.10.1179/174329306X102093 ↗
13. H.W. Zhang, Z. Zhang, and J.T. Chen: J. Mater. Process. Tech., 2007, vol. 183, pp. 62-70.10.1016/j.jmatprotec.2006.09.027 ↗
14. H.N.B. Schmidt and J. Hattel: Int. J. Offshore Polar Eng., 2004, vol. 14, pp. 296-304.
15. P. Ulysse: Int. J. Mach. Tool Manufact., 2002, vol. 42, pp. 1549-57.10.1016/S0890-6955(02)00114-1 ↗
16. P.A. Colegrove and H.R. Shercliff: Sci. Technol. Weld Joi., 2004, vol. 9, pp. 345-51.10.1179/136217104225021670 ↗
17. R. Crawford, G.E. Cook, A.M. Strauss, D.A. Hartman, and M.A. Stremler: Sci. Technol. Weld Joi., 2006, vol. 11, pp. 657-65.10.1179/174329306X147742 ↗
18. H. Schmidt and J. Hattel: Model. Simul. Mater. Sci., 2005, vol. 13, pp. 77-93.10.1088/0965-0393/13/1/006 ↗
19. S. Guerdoux and L. Fourment: Model. Simul. Mater. Sci., 2009, vol. 17, pp. 1-32.10.1088/0965-0393/17/7/075001 ↗
20. A. Arora, Z. Zhang, A. De, and T. DebRoy: Scripta Mater., 2009, vol. 61, pp. 863-66.10.1016/j.scriptamat.2009.07.015 ↗
21. B.C. Liechty and B.W. Webb: Int. J. Mach. Tool Manufact., 2008, vol. 48, pp. 1474-85.10.1016/j.ijmachtools.2008.04.005 ↗
22. R. Nandan, G.G. Roy, T.J. Lienert, and T. DebRoy: Acta Mater., 2007, vol. 55, pp. 883-95.10.1016/j.actamat.2006.09.009 ↗
23. P.A. Colegrove and H.R. Shercliff: Sci. Technol. Weld Joi., 2004, vol. 9, pp. 352-61.10.1179/136217104225021661 ↗
24. J.J. Spurk and N. Aksel: Fluid Mechanics, 2nd ed., Springer-Verlag, Berlin, Germany, 2008.
25. R. Nandan, T. DebRoy, and H.K.D.H. Bhadeshia: Prog. Mater. Sci., 2008, vol. 53, pp. 980-1023.10.1016/j.pmatsci.2008.05.001 ↗
26. W. Zhang, G.G. Roy, J.W. Elmer, and T. DebRoy: J. Appl. Phys., 2003, vol. 93, pp. 3022-33.10.1063/1.1540744 ↗
27. FLUENT online manual: http://www.ansys.com/products/fluid-dynamics/fluent.
28. P.A. Colegrove and H.R. Shercliff: J. Mater. Process. Tech., 2005, vol. 169, pp. 320-27.10.1016/j.jmatprotec.2005.03.015 ↗
29. A. Mwembela, E.B. Konopleva, and H.J. McQueen: Scripta Mater., 1997, vol. 37, pp. 1789-95.10.1016/S1359-6462(97)00344-8 ↗
30. S.X. Song, J.A. Horton, N.J. Kim, and T.G. Nieh: Scripta Mater., 2007, vol. 56, pp. 393-95.10.1016/j.scriptamat.2006.10.040 ↗
31. Z. Yu and H. Choo: Scripta Mater., 2010, vol. 64, pp. 434-37.10.1016/j.scriptamat.2010.11.009 ↗
32. M.M. Myshlyaev, H.J. McQueen, A. Mwembela, and E. Konopleva: Mater. Sci. Eng. A-Struct., 2002, vol. 337, pp. 121-33.10.1016/S0921-5093(02)00007-2 ↗
33. S. Spigarelli, M. El Mehtedi, M. Cabibbo, E. Evangelista, J. Kaneko, A. Jager, and V. Gartnerova: Mater. Sci. Eng. A-Struct., 2007, vol. 462, pp. 197-201.10.1016/j.msea.2006.03.155 ↗
34. Q. Guo, H.G. Yan, Z.H. Chen, and H. Zhang: Mater. Sci. Tech. Lond., 2006, vol. 22, pp. 725-29.10.1179/174328406X100680 ↗
35. J.H. Guo, L.Q. Chen, B. Xu, and Z. Lian: Mater. Sci. Eng. A-Struct., 2007, vol. 443, pp. 66-70.10.1016/j.msea.2006.09.040 ↗
36. S.S. Vagarali and T.G. Langdon: Acta Metall. Mater., 1982, vol. 30, pp. 1157-70.10.1016/0001-6160(82)90009-8 ↗
37. A. Galiyev, R. Kaibyshev, and G. Gottstein: Acta Mater., 2001, vol. 49, pp. 1199-1207.10.1016/S1359-6454(01)00020-9 ↗
38. Q. Guo, H.G. Yan, H. Zhang, Z.H. Chen, and Z.F. Wang: Mater. Sci. Tech. Lond., 2005, vol. 21, pp. 1349-54.10.1179/174328405X62387 ↗
39. Z. Feng, X.L. Wang, S.A. David, and P.S. Sklad: Sci. Technol. Weld Joi., 2007, vol. 12, pp. 348-56.10.1179/174329307X197610 ↗
40. T.J. Lienert, W.L. Stellwag, and L.R. Lehman: Proc. 4th Int. Symp. on Friction Stir Welding, TWI Ltd, Park City, UT, 2003, pp. S03A-P01.
41. M. Avedesian and H. Baker: ASM Specialty Handbook: Magnesium and Magnesium Alloys, ASM International, Materials Park, OH, 1999.
42. H. Palaniswamy, G. Ngaile, and T. Altan: J. Mater. Process. Tech., 2004, vol. 146, pp. 52-60.10.1016/S0924-0136(03)00844-6 ↗
43. Y.J. Chao and X.H. Qi: J. Mater. Process. Manufact., 1999, vol. 7, pp. 215-33.10.1106/LTKR-JFBM-RGMV-WVCF ↗
44. W.J. Arbegast and P.J. Hartley: Proc. 5th Int. Conf. on Trends in Welding Research, Pine Mountain, GA, 1998, pp. 541–6.
45. M.R. Barnett, D. Atwell, and A.G. Beer: Mater. Sci. Forum, 2004, vols. 467-70, pp. 435-40.10.4028/www.scientific.net/MSF.467-470.435 ↗
46. Y.S. Sato, H. Kokawa, K. Ikeda, M. Enomoto, S. Jogan, and T. Hashimoto: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 941-48.10.1007/s11661-001-0351-z ↗
47. B.C. Liechty and B.W. Webb: J. Mater. Process. Tech., 2008, vol. 208, pp. 431-43.10.1016/j.jmatprotec.2008.01.008 ↗
48. J.H. Adams, M. Ammons, and H.S. Avery: Properties and Selection: Nonferrous Alloys and Special-Purpose Materials, ASM International, Materials Park, OH, 1992.