journal article·2000-02

Characterization of Ti4AlN3

M. W. Barsoum, T. El-Raghy, A. Procopio

Publisher page

Abstract

Bulk samples of Ti4AIN3 were fabricated by reactive hot isostatic pressing (hipping) of TiH2, AlN, and TiN powders at 1275 °C for 24 hours under 70 MPa. Further annealing at 1325 °C for 168 hours under Ar resulted in dense, predominantly single-phase samples, with <1 vol pct of TiN as a secondary phase. This ternary nitride, with a grain size of ≈20 µm on average, is relatively soft (Vickers hardness 2.5 GPa), lightweight (4.6 g/cm3), and machinable. Its Young’s and shear moduli are 310 and 127 GPa, respectively. The compressive and flexural strengths at room temperature are 475 and 350 MPa, respectively. At 1000 °C, the deformation is plastic, with a maximum compressive stress of ≈450 MPa. Ti4AlN3 thermal shocks gradually, whereby the largest strength loss (50 pct) is seen at a ΔT of 1000 °C. Further increases in quench temperature, however, increase the retained strength before it ultimately decreases once again. This material is also damage tolerant; a 100 N-load diamond indentation, which produced an ≈0.4 mm defect, reduces the flexural strength by only ≈12 pct. The thermal-expansion coefficient in the 25 °C to 1100 °C temperature range is 9.7±0.2 × 10−6 °C−1. The room-temperature electrical conductivity is 0.5 × 106 (Θ · m)−1. The resistivity increases linearly with increasing temperature. Ti4AlN3 is stable up to 1500 °C in Ar, but decomposes in air to form TiN at ≈1400 °C.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: MXene and MAX Phase Materials · Metal and Thin Film Mechanics · Boron and Carbon Nanomaterials Research

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (24)

Show source-provided references
1. A.T. Procopio, T. El-Raghy, and M.W. Barsoum: Metall. Mater. Trans. A, 2000, vol. 31A, pp. 373–78.
2. J.C. Schuster and J. Bauer: J. Solid State Chem., 1984, vol. 53, pp. 260–65.10.1016/0022-4596(84)90100-2 ↗
3. H.D. Lee and W. Petuskey: J. Am. Cer. Soc., 1997, vol. 80, pp. 604–8.10.1111/j.1151-2916.1997.tb02874.x ↗
4. M.W. Barsoum, L. Farber, I. Levin, A.T. Procopio, T. El-Raghy, and A. Berner: J. Am. Cer. Soc., 1999, vol. 82, pp. 2545–47.10.1111/j.1151-2916.1999.tb02117.x ↗
5. C.J. Rawn, A.T. Procopio, T. El-Raghy, L. Farber, and M.W. Barsoum: Abstracts of the 1999 Annual Meeting of the American Ceramic Society, American Ceramic Society, 1999.
6. M.W. Barsoum and T. El-Raghy: J. Am. Cer. Soc., 1996, vol. 79, pp. 1953–56.10.1111/j.1151-2916.1996.tb08018.x ↗
7. M.W. Barsoum, D. Brodkin, and T. El-Raghy: Scripta Mater., 1997, vol. 36, pp. 535–41.10.1016/S1359-6462(96)00418-6 ↗
8. M.W. Barsoum and T. El-Raghy: J. Mater. Synth. Processing, 1997, vol. 5, pp. 197–216.
9. M.W. Barsoum, G. Yaroschuck, and S. Tyagi: Scripta Mater., 1997, vol. 37, pp. 1583–91.10.1016/S1359-6462(97)00288-1 ↗
10. A.T. Procopio: Master’s Thesis, Drexel University, Philadelphia, PA, 1999.
11. T. El-Raghy, A. Zavaliangos, M.W. Barsoum, and S.R. Kalidindi: J. Am. Cer. Soc., 1997, vol. 80, pp. 513–16.10.1111/j.1151-2916.1997.tb02861.x ↗
12. I.M. Low: J. Eur. Cer. Soc., 1998, vol. 18, pp. 709–13.10.1016/S0955-2219(97)00201-X ↗
13. I.M. Low, S.K. Lee, B. Lawn, and M.W. Barsoum: J. Am. Cer. Soc., 1998, vol. 81, pp. 225–28.10.1111/j.1151-2916.1998.tb02320.x ↗
14. M.W. Barsoum and T. El-Raghy: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 363–9.10.1007/s11661-999-0325-0 ↗
15. M.W. Barsoum, L. Farber, and T. El-Raghy: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 1722–38.
16. L. Farber, M.W. Barsoum, A. Zavaliangos, T. El-Raghy, and I. Levin: J. Am. Cer. Soc., 1998, vol. 81, pp. 1677–81.10.1111/j.1151-2916.1998.tb02532.x ↗
17. P. Finkel, M.W. Barsoum, and T. El-Raghy: J. Appl. Phys., 1999, in press.
18. R.F. Cook, B.R. Lawn, and C.J. Fairbanks: J. Am. Cer. Soc., 1985, vol. 68, pp. 604–15.10.1111/j.1151-2916.1985.tb16163.x ↗
19. T. El-Raghy, M.W. Barsoum, A. Zavaliangos, and S. Kalidindi: J. Am. Cer. Soc., 1999, vol. 82, pp. 2855–59.10.1111/j.1151-2916.1999.tb02167.x ↗
20. M. Radovic, M.W. Barsoum, T. El-Raghy, J. Seidensticker, and S. Wiederhorn: Acta Mater., in press.
21. M.W. Barsoum, T. El-Raghy, C.J. Rawn, W.D. Porter, A. Payzant, and C. Hubbard: J. Phys. Chem. Solids, 1999, vol. 60, pp. 429–39.10.1016/S0022-3697(98)00313-8 ↗
22. M. Ali: Master’s Thesis, Drexel University, Philadelphia, PA, 1999.
23. H.O. Pierson: Handbook of Refractory Carbides and Nitrides, Noyes Publications, Park Ridge, NJ, 1996.
24. W. Lengauer, S. Binder, K. Ainger, P. Ettmayer, A. Gillou, J. Debuigne, G. Groboth: J. Alloys Compounds, 1995, vol. 217, pp. 137–47.10.1016/0925-8388(94)01315-9 ↗