journal article·2012-12

Submerged Friction-Stir Welding (SFSW) Underwater and Under Liquid Nitrogen: An Improved Method to Join Al Alloys to Mg Alloys

Mohammad Ammar Mofid, Amir Abdollah-Zadeh, Farshid Malek Ghaini, Cemil Hakan Gür

Publisher page

Abstract

Submerged friction-stir welding (SFSW) underwater and under liquid nitrogen is demonstrated as an alternative and improved method for creating fine-grained welds in dissimilar metals. Plates of AZ31 (Mg alloy) and AA5083 H34 were joined by friction-stir welding in three different environments, i.e., in air, water, and liquid nitrogen at 400 rpm and 50 mm/min. The temperature profile, microstructure, scanning electron microscopy (SEM)-energy-dispersive spectroscopy (EDS) analysis, X-ray diffraction (XRD), hardness, and tensile testing results were evaluated. In the stir zone of an air-welded specimen, formation of brittle intermetallic compounds of Al3Mg2, Al12Mg17, and Al2Mg3 contributed to cracking in the weld nugget. These phases were formed because of constitutional liquation. Friction-stir welding underwater and under liquid nitrogen significantly suppresses the formation of intermetallic compounds because of the lower peak temperature. Furthermore, the temperature profiles plotted during this investigation indicate that the largest amount of ∆T is generated by the weld under liquid nitrogen, which is performed at the lowest temperature. It is shown that in low-temperature FSW, the flow stress is higher, plastic contribution increases, and so adiabatic heating, a result of high strain and high strain-rate deformation, drives the recrystallization process beside frictional heat.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloys Composites Properties · Magnesium Alloys: Properties and Applications

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (29)

Show source-provided references
1. J.A. Esparza, E.A. Trillo, and L.E. Murr: J. Mater. Sci. Lett., 2002, vol. 21, pp. 917–20.10.1023/A:1016061303955 ↗
2. W.V. Vaidya, M. Horstmann, E. Seib, K. Toksoy, and M. Kocak: Adv. Eng. Mater., 2006, vol. 8, pp. 399–406.10.1002/adem.200600015 ↗
3. C. Liu, D.L. Chen, S. Bhole, X. Cao, and M. Jahazi: Mater. Charact., 2009, vol. 60, pp. 370–76.10.1016/j.matchar.2008.10.009 ↗
4. D. Dietrich, D. Nickel, and M. Krause: J. Mater. Sci., 2011, vol. 46, pp. 357–64.10.1007/s10853-010-4841-5 ↗
5. Y.C. Chen and K. Nakata: Scripta Mater., 2007, vol. 58, pp. 433–36.10.1016/j.scriptamat.2007.10.033 ↗
6. Y.S. Sato and C. Park: Scripta Mater., 2004, vol. 50, pp. 1233–36.10.1016/j.scriptamat.2004.02.002 ↗
7. A.A. McLean, G.L.F. Powell, I.H. Brown, and V.M. Linton: Sci. Tech. Weld. J., 2003, vol. 8, pp. 462–64.10.1179/136217103225009134 ↗
8. A.C. Somasekharan and L.E. Murr: Mater. Charact., 2004, vol. 52, pp. 49–64.10.1016/j.matchar.2004.03.005 ↗
9. A.C. Somasekharan and L.E. Murr: Microstructural Details of Friction-Stir Weld Interfaces, Friction Stir Welding and Processing, 3rd ed., K.V. Jata, eds., TMS, Warrendale, PA, 2005, pp. 261–68.
10. S. Hirano, K. Okamoto, M. Doi, H. Okamura, M. Inagaki, and Y. Aono: Q. J. Jpn. Weld. Soc., 2003, vol. 21, pp. 539–45.10.2207/qjjws.21.539 ↗
11. R. Zettler: Adv. Eng. Mater., 2006, vol. 8, pp. 415–21.10.1002/adem.200600030 ↗
12. L.E. Murr: Mater. Res. Inn., 1998, vol. 2, pp. 150–63.10.1007/s100190050078 ↗
13. Y.S. Sato: Mater. Sci. Eng. A, 2004, vol. A369, pp. 138–43.10.1016/j.msea.2003.11.035 ↗
14. X. Cao and M. Jahazi: Adv. Manuf. Technol., 2009, vol. 56, pp. 370–76.
15. V. Firouzdor and S. Kou: Metall. Mater. Trans. A, 2010, vol. 41A, pp. 2914–35.10.1007/s11661-010-0340-1 ↗
16. Y.J. Kwon, I. Shigematsu, and N. Saito: Mater. Lett., 2008, vol. 62, pp. 3827–29.10.1016/j.matlet.2008.04.080 ↗
17. A.K. Kostka, R.S. Coelho, J. dos Santos, and A.R. Pyzalla: Scripta Mater., 2009, vol. 60, pp. 953–56.10.1016/j.scriptamat.2009.02.020 ↗
18. J. Yan, Z. Xu, Z. Li, L. Li, and S. Yang: Scripta Mater., 2005, vol. 53, pp. 585–89.10.1016/j.scriptamat.2005.04.022 ↗
19. F.U. Rui-dong, S. Zeng-qiang, S. Rui-cheng, L. Ying, L. Hui-jie, and L. Lei: Mater Des., 2011, vol. 32, pp. 4825–31.10.1016/j.matdes.2011.06.021 ↗
20. D. Sakurada, K. Katoh, and H. Tokisue: J. Jpn. Inst. Light Met., 2002, vol. 52, pp. 22–29.10.2464/jilm.52.2 ↗
21. T. Bloodworth: Master’s Thesis, Vanderbilt University, Nashville, TN, 2009.
22. D.C. Hofmann and S. Kennesh: Mater. Sci. Eng. A, 2005, vol. 402, pp. 234–41.10.1016/j.msea.2005.04.032 ↗
23. ASTM A1038-10, “Standard Practice for Portable Hardness Testing by the Ultrasonic Contact Impedance Method,” 2010.
24. R.E. Reed-Hill: Physical Metallurgy Principles, PWS-Kent, Boston, MA, 1973.
25. P. Greenfield and M.B. Bever: Acta Metall., 1957, vol. 5, pp. 125–30.10.1016/0001-6160(57)90016-0 ↗
26. P. Heurtier, M.J. Jones, and C. Desrayaud: Mater. Process. Tech., 2006, vol. 171, pp. 348–57.10.1016/j.jmatprotec.2005.07.014 ↗
27. ASM International: ASM Handbook, vol. 3: Alloy Phase Diagrams, ASM International, Materials Park, OH, 1998.
28. X. Cao and M. Jahazi: Mater. Des., 2011, vol. 32, pp. 1–11.10.1016/j.matdes.2010.06.048 ↗
29. G.M. Cantin, S.A. David, L. Curzio, and S.S. Babu: Proc. 7 th Int. Conf. on Trends in Welding Research, Callaway Gardens Resort, Pine Mountains, GA, 2005, pp. 185–190.