journal article·2001-09

Influence of tempering on the microstructure and mechanical properties of HSLA-100 steel plates

S. K. Dhua, D. Mukerjee, D. S. Sarma

Publisher page

Abstract

The influence of tempering on the microstructure and mechanical properties of HSLA-100 steel (with C-0.04, Mn-0.87, Cu-1.77, Cr-0.58, Mo-0.57, Ni-3.54, and Nb-.038 pct) has been studied. The plate samples were tempered from 300 °C to 700 °C for 1 hour after austenitizing and water quenching. The transmission electron microscopy (TEM) studies of the as-quenched steel revealed a predominantly lath martensite structure along with fine precipitates of Cu and Nb(C, N). A very small amount of retained austenite could be seen in the lath boundaries in the quenched condition. Profuse precipitation of Cu could be noticed on tempering at 450 °C, which enhanced the strength of the steel significantly (yield strength (YS)—1168 MPa, and ultimate tensile strength (UTS)—1219 MPa), though at the cost of its notch toughness, which dropped to 37 and 14 J at 25 °C and −85 °C, respectively. The precipitates became considerably coarsened and elongated on tempering at 650 °C, resulting in a phenomenal rise in impact toughness (Charpy V-notch (CVN) of 196 and 149 J, respectively, at 25 °C and −85 °C) at the expense of YS and UTS. The best combination of strength and toughness has been obtained on tempering at 600 °C for 1 hour (YS-1015 MPa and UTS-1068 MPa, with 88 J at −85 °C).
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Hydrogen embrittlement and corrosion behaviors in metals

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (23)

Show source-provided references
1. E.J. Czyryca: Key Engineering Materials, Trans Tech Publications, Aedermannsdorf, Switzerland, 1993, vols. 84–85, pp. 491–520.
2. B.A. Graville: Proc. Int. Conf. on Welding of HSLA (Microalloyed) Structural Steels, ASM INTERNATIONAL, Metals Park, OH, 1978, pp. 85–101.
3. A.D. Wilson, E.G. Hamburg, D.J. Colvin, S.W. Thompson, G. Krauss: Proc. Int. Conf. on Microalloyed HSLA Steel, Microalloying’88, ASM INTERNATIONAL, Metals Park, OH, 1988, pp. 259–75.
4. A.K. Lis, M. Mujahid, C.I. Garcia, and A.J. DeArdo: Speich Symp. Proc., ISS, Warrendale, PA, 1992, pp. 129–38.
5. R.H. Philips, J.G. Williams, and J.E. Croll: Proc. Int. Conf. on Microalloyed HSLA Steels, Microalloying’88, ASM INTERNATIONAL, Metals Parrk, OH, 1988, pp. 235–47.
6. M.T. Miglin, J.P. Hirth, A.R. Rosenfield, and W.A.T. Clark: Metall. Trans. A, 1986, vol. 17A, pp. 791–98.10.1007/BF02643854 ↗
7. S.S. Banadkouki Ghasemi, D. Yu, and D.P. Dunne: Iron Steel Inst. Jpn., 1996, vol. 36, pp. 61–67.10.2355/isijinternational.36.61 ↗
8. G.E. Hicho, C.H. Brady, L.C. Smith, and R.J. Fields: J. Heat Treating, 1987, vol. 5, pp. 7–19.10.1007/BF02831616 ↗
9. G.E. Hicho, S. Singhal, L.C. Smith, and R.J. Fields: Proc. Int. Conf. on HSLA Steels, Technology and Applications, ASM INTERNATIONAL, Metals Park, OH, 1984, pp. 705–13.
10. Takashi Abe, Masayoshi Kurihara, and Histoshi Tagawa: Trans. Iron Steel Inst. Jpn., 1987, vol. 27, pp. 478–84.10.2355/isijinternational1966.27.478 ↗
11. S.W. Thompson and G. Krauss: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 1573–88.10.1007/BF02649816 ↗
12. A.D. Wilson: J. Met., 1987, vol. 29, pp. 39–48.
13. S.W. Thompson, D.J. Colvin, and G. Krauss: Metall. Mater. Trans. A, 1990, vol. 21A, pp. 1493–1507.10.1007/BF02672564 ↗
14. S.W. Thompson, D.J. Colvin, and G. Krauss: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 1554–68.
15. A.G. Fox, S. Mikalac, and M.G. Vassilaros: Speich Symp. Proc., ISS, Warrendale, PA, 1992, pp. 155–61.
16. M. Mujahid, A.K. Lis, C.I. Garcia, and A.J. DeArdo: J. Mater. Eng. Performance, 1998, vol. 7, pp. 247–57.10.1361/105994998770347981 ↗
17. R.P. Foley and M.E. Fine: Proc. Int. Conf. on Processing, Microstructure and Properties of Microalloyed and Other Modern HSLA Steels, ISS, Warrendale, PA, 1991, pp. 315–30.
18. M.A. Cooke, B.H. Chapman, and S.W. Thompson: Scripta Metall., 1992, vol. 26, pp. 1553–58.10.1016/0956-716X(92)90255-D ↗
19. R.P. Foley and M.E. Fine: Speich Symp. Proc., ISS, Warrendale, PA, 1992, pp. 139–54.
20. S.R. Goodman, S.S. Brenner, and J.R. Low: Metall. Trans. A, 1973, vol. 4, pp. 2363–78.10.1007/BF02669376 ↗
21. P.J. Othen, M.L. Jenkins, G.D.W. Smith, and W.J. Phythian: Phil. Mag. Lett., 1991, vol. 64, pp. 383–91.10.1080/09500839108215121 ↗
22. I. LeMay and M.R. Krishnadev: in Copper in Iron and Steel, I. LeMay and L.M. Schetky, eds., John Wiley and Sons, New York, NY, 1982, pp. 5–43.
23. S.J. Mikalac and M.G. Vassilaros: Proc. Int. Conf. on Processing, Microstructure and Properties of Microalloyed and Other Modern HSLA Steels, ISS, Warrendale, PA, 1991, pp. 331–43.