Influence of binder-to-sand ratio on mechanical and durability properties of ultra-high-performance concrete reinforced with novel polyoxymethylene fiber
Source abstract
Abstract
Abstract Ultra-high performance concrete (UHPC) faces cost and shrinkage challenges due to high binder contents. This study systematically investigates the influence of varying binder-to-sand (B/S) ratios (0.8, 0.9, 1.0, and 1.2) coupled with novel polyoxymethylene fibers (POMFs, 0 and 2% dosages) on UHPC properties. A fixed water-to-binder ratio (0.17) and 50% ground granulated blast-furnace slag replacement were used. Freshness, mechanical properties, durability, and microstructural properties were evaluated. Results indicate that the B/S ratio critically governs UHPC performance. Contrary to the assumption that higher binder content is always superior, an optimal balance emerged at a B/S ratio of 0.9. This ratio yielded the highest 28-day compressive and splitting tensile strengths, the lowest water absorption, and exceptional sulfate resistance, with no strength degradation after 180 days. A low B/S ratio (0.8) caused insufficient aggregate coating, increasing porosity, and reducing strength. Conversely, an excessive B/S ratio (1.2) induced severe autogenous shrinkage and microcracking, impairing durability and strength. While a 2% POMF addition provided limited gains in compressive strength, it significantly improved splitting tensile strength and shifted the failure mode from brittle to ductile. Scanning electron microscopy confirmed that POMF’s hydrophilic nature ensures excellent interfacial bonding with the matrix. Ultimately, a B/S ratio of 0.9 provides the optimal eco-efficient mix design, balancing high performance with material economy for UHPC engineering applications.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Innovative concrete reinforcement materials · Concrete and Cement Materials Research · Concrete Properties and Behavior
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Civil Engineering, National Kaohsiung University of Science and Technology , No. 415 Jiangong Road, Sanmin District , Kaohsiung City , Taiwan
References (50)
Show source-provided references
1. Bajaber, M.A., Hakeem, I.Y., UHPC evolution, development, and utilization in construction: A review, J. Mater. Res. Technol., 2021; 10: 105810.1016/j.jmrt.2020.12.051 ↗
2. Yoo, D.-Y., Banthia, N., Mechanical properties of ultra-high-performance fiber-reinforced concrete: A review, Cem. Concr. Compos., 2016; 73: 26710.1016/j.cemconcomp.2016.08.001 ↗
3. Xu, D., Tang, J., Hu, X., Yu, C., Han, F., Sun, S., et al., The influence of curing regimes on hydration, microstructure and compressive strength of ultra-high performance concrete: A review, J. Build. Eng., 2023; 76: 10740110.1016/j.jobe.2023.107401 ↗
4. Yoo, D.-Y., Oh, T., Banthia, N., Nanomaterials in ultra-high-performance concrete (UHPC) – A review, Cem. Concr. Compos., 2022; 134: 10473010.1016/j.cemconcomp.2022.104730 ↗
5. Shi, C., Wu, Z., Xiao, J., Wang, D., Huang, Z., Fang, Z., Genetic and biochemical mechanisms of pollen wall development, Constr. Build. Mater., 2015; 101: 74110.1016/j.tplants.2015.07.010 ↗
6. Ghafari, E., Costa, H., Júlio, E., Statistical mixture design approach for eco-efficient UHPC, Cem. Concr. Compos., 2015; 55: 1710.1016/j.cemconcomp.2014.07.016 ↗
7. Yu, R., Spiesz, P., Brouwers, H.J.H., Mix design and properties assessment of ultra-high performance fibre reinforced concrete (UHPFRC, Cem. Concr. Res., 2014; 56: 2910.1016/j.cemconres.2013.11.002 ↗
8. Sharma, R., Jang, J.G., Bansal, P.P., A comprehensive review on effects of mineral admixtures and fibers on engineering properties of ultra-high-performance concrete, J. Build. Eng., 2022; 45: 10331410.1016/j.jobe.2021.103314 ↗
9. Song, J., Banthia, N., Yoo, D.-Y., Effect of supplementary cementitious materials on durability of ultra-high-performance concrete: A review, Cem. Concr. Compos., 2025; 163: 10619810.1016/j.cemconcomp.2025.106198 ↗
10. Khan, I., Yong, G., Role of supplementary cementiteous materials in mitigating heat of hydration in mass concrete elements, Constr. Build. Mater., 2024; 431: 13648210.1016/j.conbuildmat.2024.136482 ↗
11. Bellum, R.R., Muniraj, K., Madduru, S.R.C., Exploration of mechanical and durability characteristics of fly ash-GGBFS based green geopolymer concrete, SN Appl. Sci., 2020; 2: 91910.1007/s42452-020-2720-5 ↗
12. Zaki, A., Kusumawijaya, A.M., Rosyidi, S.A.P., Abdullah, M.Z., Mahbubi, K., Ibrahim, Z., Non-destructive based performance analysis of eco-friendly concrete mixes against corrosion and structural degradation, Structures, 2025; 81: 11023310.1016/j.istruc.2025.110233 ↗
13. Zhang, Z., Ahmad, N., Shrestha, A., Tang, Z., Cai, Z., Ergashev, R., et al., Investigation of fresh, shrinkage, and mechanical properties in iron sand high-strength engineered cementitious composites: Effects of water-to-binder ratio and fiber volume fraction, Case Stud. Constr. Mater., 2025; 22: e0413810.1016/j.cscm.2024.e04138 ↗
14. Kim, H., Koh, T., Pyo, S., Enhancing flowability and sustainability of ultra high performance concrete incorporating high replacement levels of industrial slags, Constr. Build. Mater., 2016; 123: 15310.1016/j.conbuildmat.2016.06.134 ↗
15. Wei, X., Zhu, H., Chen, Q., Ju, J.W., Cai, W., Yan, Z., et al., Microstructure-based prediction of UHPC’s tensile behavior considering the effects of interface bonding, matrix spalling and fiber distribution, Cem. Concr. Compos., 2023; 139: 10501510.1016/j.cemconcomp.2023.105015 ↗
16. Wang, Y., Qiao, P., Sun, J., Chen, A., Influence of fibers on tensile behavior of ultra-high performance concrete: A review, Constr. Build. Mater., 2024; 430; 13643210.1016/j.conbuildmat.2024.136432 ↗
17. Yao, Z., Xu, T., Dong, M., Huang, H., Zeng, Q., Xu, H., et al., Engineered cementitious composites with 100% coral sand aggregate: Effect of water-to-binder and sand-to-binder ratios on mechanical properties and cracking behavior, J. Build. Eng., 2025; 115: 11458910.1016/j.jobe.2025.114589 ↗
18. Zailani, W.W., Apandi, N.M., Adesina, A., Alengaram, U.J., Faris, M.A., Tahir, M.F., Physico-mechanical properties of geopolymer mortars for repair applications: Impact of binder to sand ratio, Constr. Build. Mater., 2024; 412: 13472110.1016/j.conbuildmat.2023.134721 ↗
19. Paul, A., John, E., Study on the optimisation of cement and binder content to develop a sustainable high-performance concrete, Mater. Today: Proc., 2023. In Press, 10.1016/j.matpr.2023.12.012
20. Wahab, S., Abbasi, A.M., Ahmed, A., Khan, I.U., Influence of acetic acid treated recycled concrete aggregates on the rheological and mechanical properties of self-compacting concrete: Experiments and machine learning, Constr. Build. Mater., 2025; 491: 14277010.1016/j.conbuildmat.2025.142770 ↗
21. Zhao, S., Liu, R., Liu, J., Yang, L., Comparative study on the effect of steel and plastic synthetic fibers on the dynamic compression properties and microstructure of ultra-high-performance concrete (UHPC), Compos. Struct., 2023; 324: 11757010.1016/j.compstruct.2023.117570 ↗
22. Shen, D., Liu, C., Luo, Y., Shao, H., Zhou, X., Bai, S., Early-age autogenous shrinkage, tensile creep, and restrained cracking behavior of ultra-high-performance concrete incorporating polypropylene fibers, Cem. Concr. Compos., 2023; 138: 10494810.1016/j.cemconcomp.2023.104948 ↗
23. Pakravan, H.R., Ozbakkaloglu, T., Synthetic fibers for cementitious composites: A critical and in-depth review of recent advances, Constr. Build. Mater., 2019; 207: 49110.1016/j.conbuildmat.2019.02.078 ↗
24. Deng, Z., Chen, P., Liu, X., Du, L., Tan, J., Liang, N., Study on the tensile and compressive mechanical properties of multi-scale fiber-reinforced concrete: Laboratory test and mesoscopic numerical simulation, J. Build. Eng., 2024; 86: 10885210.1016/j.jobe.2024.108852 ↗
25. Shen, C., Tang, D., Lyu, Z., Yang, C., Yu, L., Distribution of coarse aggregate and steel fibers in ultra-high performance concrete containing coarse aggregate (UHPC-CA) and their effect on the flexural performance, Constr. Build. Mater., 2024; 421: 13566610.1016/j.conbuildmat.2024.135666 ↗
26. Zhang, W., Xu, X., Wang, H., Wei, F., Zhang, Y., Experimental and numerical analysis of interfacial bonding strength of polyoxymethylene reinforced cement composites, Constr. Build. Mater., 2019: 207: 110.1016/j.conbuildmat.2019.02.122 ↗
27. Rui, Y., Li, K., Yang, T., Tang, L., Dong, M., Shi, Z., Comparative study on the effect of steel and polyoxymethylene fibers on the characteristics of ultra-high performance concrete (UHPC), Cem. Concr. Compos., 2022; 127: 10441810.1016/j.cemconcomp.2022.104418 ↗
28. Lin, J.-X., Luo, R.-H., Su, J.-Y., Guo, Y.-C., Chen, W.-S., Coarse synthetic fibers (PP and POM) as a replacement to steel fibers in UHPC: Tensile behavior, environmental and economic assessment, Constr. Build. Mater., 2024; 412: 13465410.1016/j.conbuildmat.2023.134654 ↗
29. Shen, D., Shao, H., Huang, Y., Liu, C., Huang, Q., Zhao, C., Influence of polyoxymethylene fibers on autogenous shrinkage, tensile creep, and cracking resistance of ultra-high performance concrete, Cem. Concr. Compos., 2025; 154: 105766.10.1016/j.cemconcomp.2025.106090 ↗
30. ACI Committee 239, Ultra-high-performance concrete: An emerging technology report (ACI 239R-18), American Concrete Institute, Farmington Hills, 2018
31. Ramakrishnan, K., Pugazhmani, G., Sripragadeesh, R., Muthu, D., Venkatasubramani, C., Experimental study on the mechanical and durability properties of concrete with waste glass powder and ground granulated blast furnace slag as supplementary cementitious materials, Constr. Build. Mater., 2017; 156: 73910.1016/j.conbuildmat.2017.08.183 ↗
32. Xu, D., Tang, J., Hu, X., Zhou, Y., Yu, C., Han, F., et al., Influence of silica fume and thermal curing on long-term hydration, microstructure and compressive strength of ultra-high performance concrete (UHPC), Constr. Build. Mater., 2023; 395: 13237010.1016/j.conbuildmat.2023.132370 ↗
33. Zhang, Q., Shu, X., Yang, Y., Wang, X., Liu, J., Ran, Q., Preferential adsorption of superplasticizer on cement/silica fume and its effect on rheological properties of UHPC, Constr. Build. Mater., 2022; 359: 12951910.1016/j.conbuildmat.2022.129519 ↗
34. Huang, H., Gao, X., Khayat, K.H., Su, A., Influence of fiber alignment and length on flexural properties of UHPC, Constr. Build. Mater., 2021; 290: 12286310.1016/j.conbuildmat.2021.122863 ↗
35. Wen, K.-W., Su, Y.-F., Mo, K.H., Hung, C.-C., Time-dependent rheology, green strength, and buildability of 3D-printed ultra-high performance concrete incorporating various fiber types and contents, J. Build. Eng., 2026; 117: 11491910.1016/j.jobe.2025.114919 ↗
36. Graybeal, B.A., The performance of ultra-high performance concrete, US Department of Transportation, Federal Highway Administration, Washington, DC, 2014
37. Moula, S., Fraj, A.B., Trauchessec, R., Wattez, T., Bouasker, M., Ali, N.B.H., New approach for developing an eco-friendly ultra-high performance concrete making efficient use of ground granulated blast-furnace slag, Constr. Build. Mater., 2025; 503: 14451210.1016/j.conbuildmat.2025.144512 ↗
38. Zheng, Z., Tan, H., Zeng, J., Yang, J., Zheng, G., Zhu, M., et al., Ecological ultra-high performance concrete incorporating multi-scale and multi-source solid wastes as nano-micron filler, ultrafine binder and fine aggregate, Constr. Build. Mater., 2025; 463: 14000210.1016/j.conbuildmat.2025.140002 ↗
39. Zhang, J.C., Li, B.J., Chen, W.Y., Guo, R.X., Experimental investigations on tensile strength and fracture toughness of a polyoxymethylene fiber reinforced concrete, Theor. Appl. Fract. Mech., 2024; 130: 10425010.1016/j.tafmec.2023.104250 ↗
40. Zhang, G., Zhang, W., Li, Y., Chen, H., Ge, J., Pan, P., et al., The effect of curing regimes on the hydration products of lightweight ultra-high performance concrete: From experiments to MD simulations, Constr. Build. Mater., 2024; 412: 13486510.1016/j.conbuildmat.2024.134865 ↗
41. Anunike, G.S., Tarabin, M., Hisseine, O.A., Assessment of the mechanical, radiation shielding, and durability of ultra-high-performance concrete for radiation shielding: A review, Constr. Build. Mater., 2025; 474: 14089610.1016/j.conbuildmat.2025.140896 ↗
42. Tanimura, M., Sato, R., Influence of autogenous shrinkage on the microstructure and permeability of high-strength concrete, Cem. Concr. Res., 2017; 99: 119
43. Fonseka, N.H.I.C., Nanayakkara, S.M.A., Assessment of Concrete Durability by Surface Resistivity and Initial Surface Absorption in 12th International Conference on Structural Engineering and Construction Management, Springer, Singapore, 2022, p. 60310.1007/978-981-19-2886-4_43 ↗
44. Ou, Y., Ji, X., Pan, J., Su, A., Gao, X., Sun, M., et al., Long-term performance and microstructure evolution of UHPC with exposure to seawater immersion, J. Build. Eng., 2025; 111: 11364010.1016/j.jobe.2025.113640 ↗
45. Turgeon-Malette, V., Chen, X., Bah, A.S., Conciatori, D., Sanchez, T., Teguedy, M.C., et al., Chloride ion permeability of ultra-high-performance fiber-reinforced concrete under sustained load, J. Build. Eng., 2023; 66: 10584210.1016/j.jobe.2023.105842 ↗
46. Zhang, H., Ji, T., Liu, H., Performance evolution of recycled aggregate concrete (RAC) exposed to external sulfate attacks under full-soaking and dry-wet cycling conditions, Constr. Build. Mater., 2020; 248: 11867510.1016/j.conbuildmat.2020.118675 ↗
47. Gu, Y., Martin, R.-P., Metalssi, O.O., Fen-Chong, T., Dangla, P., Pore size analyses of cement paste exposed to external sulfate attack and delayed ettringite formation, Cem. Concr. Res., 2019; 123: 105766.10.1016/j.cemconres.2019.05.011 ↗
48. Pham, T.M., Fibre-reinforced concrete: State-of-the-art-review on bridging mechanism, mechanical properties, durability, and eco-economic analysis, Case Stud. Constr. Mater., 2025; 22: e0457410.1016/j.cscm.2025.e04574 ↗
49. Chen, T., Gao, X., Ren, M., Effects of autoclave curing and fly ash on mechanical properties of ultra-high performance concrete, Constr. Build. Mater., 2018; 158: 86410.1016/j.conbuildmat.2017.10.074 ↗
50. Yazıcı, H., Deniz, E., Baradan, B., The effect of autoclave pressure, temperature and duration time on mechanical properties of reactive powder concrete, Constr. Build. Mater., 2013; 42: 5310.1016/j.conbuildmat.2013.01.003 ↗