Influence of elevated temperature on bond performance of basalt FRP bars with steel fiber-reinforced concrete
Source abstract
Abstract
Abstract Basalt fiber-reinforced polymer (BFRP) rebars offer a cost-effective, high-temperature, chemical-resistant, and eco-friendly alternative to steel bars. However, their widespread adoption hinges on understanding their structural and mechanical performance, particularly bond with concrete at elevated temperatures. This research investigates the bond of BFRP rebars in plain and fiber-reinforced concretes after high-temperature exposure via beam-end tests, comparing them to steel bars. The parameters considered in the study include concrete type (plain and steel fiber-reinforced), the type of rebar (steel and BFRP), and exposure temperatures (ambient temperature, 100°C, and 200°C). Twenty-four beam-end test samples were prepared and tested. The observed bond performance was evaluated based on failure modes, bond stress-slip behavior, and average bond strength. Interestingly, the bond strength of BFRP rebars showed a slight increase under elevated temperatures, with gains of about 8–17% at 200°C depending on the concrete type. Although initially lower than steel at ambient conditions, BFRP exhibited comparable or slightly higher average bond indices at 200°C, while both showed similar bond strength at 100°C. Given n = 2 per condition, these trends are indicative rather than definitive. These trends suggest potential thermal resilience of BFRP at moderate temperatures; however, the observations are based on limited replicates, and the bonded regions experienced equivalent thermal exposure. To model the bond stress–slip relationship of BFRP bars at higher temperatures, an existing model for FRP bars was modified. Comparisons of bond strength are made with available models from different codes and researchers.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Structural Behavior of Reinforced Concrete · Masonry and Concrete Structural Analysis · Concrete Corrosion and Durability
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Chair of Research and Studies in Strengthening and Rehabilitation of Structures, Department of Civil Engineering, College of Engineering, King Saud University , 11421 , Riyadh , Saudi Arabia
References (40)
Show source-provided references
1. Abbas, H., Alanazi, M.A., Elsanadedy, H., Almusallam, T., Abadel, A., Al-Salloum, Y., Effect of tie spacing and GFRP rebar diameter on compression behavior of concrete columns, J. Build. Eng., 2023, 72: 10674010.1016/j.jobe.2023.106740 ↗
2. Auman, H., Stratford, C., Palermo, A., An overview of research and applications of FRP in New Zealand reinforced concrete structures, Struct. Eng. Int., 2020, 30(2): 201–20810.1080/10168664.2019.1699491 ↗
3. Elsanadedy, H.M., Abbas, H., Al-Salloum, Y.A., Almusallam, T.H., Prediction of intermediate crack debonding strain of externally bonded FRP laminates in RC beams and one-way slabs, J. Compos. Constr., 2014, 18(5): 0401400810.1061/(ASCE)CC.1943-5614.0000462 ↗
4. Li, T., Liu, T., Jin, C., Huang, J., Application of phenolic-based BFRP rebars adapted to high temperature in beam strengthened by NSM technique, Struct. Eng. Int., 2025, 35(2): 276–28510.1080/10168664.2024.2365822 ↗
5. Rizkalla, S., Hassan, T., Effectiveness of FRP for strengthening concrete bridges, Struct. Eng. Int., 2002, 12(2): 89–9510.2749/101686602777965577 ↗
6. Parvizi, M., Investigation of bond behaviour between GFRP reinforcing bars and concrete containing seawater (Doctoral dissertation, Université d’Ottawa/University of Ottawa); 2019
7. Henin, E., Tawadrous, R., Morcous, G., Effect of surface condition on the bond of basalt fiber-reinforcement polymer bars in concrete, Constr. Build. Mater., 2019, 226: 449–45810.1016/j.conbuildmat.2019.07.160 ↗
8. ACI Committee 440, Guide for the design and construction of structural concrete reinforced with fiber-reinforced polymer bars (ACI 440.1R-15R), American Concrete Institute; 2015
9. ACI Committee 440, Specification for carbon and glass fiber-reinforced polymer bar materials for concrete reinforcement (ACI 440.6M-08M), ACI: Farmington Hills, Michigan, USA; 2018
10. CSA (Canadian Standards Association), Design and construction of buildings components with fiber-reinforced polymers. CSA S806-12, Toronto, ON, Canada; 2012
11. CSA (Canadian Standards Association), Canadian highway bridge design code. CSA-S6-S19, Rexdale, ON, Canada; 2014
12. CSA (Canadian Standards Association), Annex E – Specification for fibre-reinforced polymers. S807:19. Toronto, ON, Canada; 2019
13. Adhikari, S., Mechanical properties and flexural applications of basalt fiber reinforced polymer (BFRP) bars (Doctoral dissertation, University of Akron); 2009
14. Wu, Z., Wang, X., Wu, G., Advancement of structural safety and sustainability with basalt fiber reinforced polymers, In Proceedings of the 6th International Conference on FRP Composites in Civil Engineering (CICE2012), Rome, Italy; 2012, June
15. Vincent, P., Ahmed, E., Benmokrane, B., Characterization of basalt fiber-reinforced polymer (BFRP) reinforcing bars for concrete structures, In Proceedings of the 3rd Specialty Conference on Material Engineering & Applied Mechanics, Canadian Society of Civil Engineers, Montreal, Canada. May, Vol. 29; 2013, January
16. Altalmas, A., El Refai, A., Abed, F., Bond degradation of basalt fiber-reinforced polymer (BFRP) bars exposed to accelerated aging conditions, Constr. Build. Mater., 2015, 81: 162–17110.1016/j.conbuildmat.2015.02.036 ↗
17. Benmokrane, B., Elgabbas, F., Ahmed, E.A., Cousin, P., Characterization and comparative durability study of glass/vinylester, basalt/vinylester, and basalt/epoxy FRP bars, J. Compos. Constr., 2015, 19(6): 0401500810.1061/(ASCE)CC.1943-5614.0000564 ↗
18. Wang, H., Sun, X., Peng, G., Luo, Y., Ying, Q., Experimental study on bond behaviour between BFRP bar and engineered cementitious composite, Constr. Build. Mater., 2015, 95: 448–45610.1016/j.conbuildmat.2015.07.135 ↗
19. Hassan, M., Benmokrane, B., ElSafty, A., Fam, A., Bond durability of basalt-fiber-reinforced-polymer (BFRP) bars embedded in concrete in aggressive environments, Composites, Part B, 2016, 106: 262–27210.1016/j.compositesb.2016.09.039 ↗
20. Li, C., Gao, D., Wang, Y., Tang, J., Effect of high temperature on the bond performance between basalt fibre reinforced polymer (BFRP) bars and concrete, Constr. Build. Mater., 2017, 141: 44–5110.1016/j.conbuildmat.2017.02.125 ↗
21. ISIS Canada, Reinforcing concrete structures with fibre reinforced polymers. Design manual no. 3. Sept. 2007, ISIS Canada Research Network; 2007
22. Liu, H., Yang, J., Wang, X., Bond behavior between BFRP bar and recycled aggregate concrete reinforced with basalt fiber, Constr. Build. Mater., 2017, 135: 477–48310.1016/j.conbuildmat.2016.12.161 ↗
23. Yi, Y., Wang, X., Liu, J., Liu, X., Yi, X., Chen, Z., et al., Effect of elevated temperature on tensile properties of thermoplastic FRP bars and thermoplastic FRP-concrete bond behavior, J. Build. Eng., 2025, 102: 11203210.1016/j.jobe.2025.112032 ↗
24. Liang, K., Chen, L., Su, R.K.L., Bond behavior of basalt fiber-reinforced polymer bars (BFRP) embedded in ultra-high-performance concrete after elevated temperature exposure, Constr. Build. Mater., 2025, 481: 14153110.1016/j.conbuildmat.2025.141531 ↗
25. Prakash, R.S., Parthasarathi, N., Experimental and numerical study on FRP-rehabilitated RC beam-column joints at high temperature with artificial neural network, Sci. Rep., 2025, 15(1): 3001610.1038/s41598-025-16055-9 ↗
26. ACI 408 Committee, Bond and development of straight reinforcing bars in tension (ACI 408R-03), American Concrete Institute: Detroit, Michigan, US, 2003, p. 49
27. ASTM A944, Standard test method for comparing bond strength of steel reinforcing bars to concrete using beam-end specimens, Annual book of ASTM standards; 2015
28. ASTM C39/C39M-18, Standard test method for compressive strength of cylindrical concrete specimens, ASTM International: West Conshohocken, PA; 2018
29. ASTM C496-17, Standard test method for splitting tensile strength of cylindrical concrete specimens, ASTM International: West Conshohocken, PA; 2017
30. Taha, A., Alnahhal, W., Bond durability and service life prediction of BFRP bars to steel FRC under aggressive environmental conditions, Compos. Struct., 2021, 269: 11403410.1016/j.compstruct.2021.114034 ↗
31. Liu, Z., Liu, H., Xu, W., Liu, B., Zhong, Y., Geng, J., et al., Investigation of the bond properties between hybrid fiber-reinforced concrete and BFRP bars after exposure to high temperature, Mater. Constr., 2024, 74(353): e334–e33410.3989/mc.2024.361123 ↗
32. Heshmat, M., El-Shafie, H., Elgabbas, F., Investigate the bond performance of basalt FRP bars under the effect of severe conditions, Sci. Rep., 2025, 15(1): 2014210.1038/s41598-025-04989-z ↗
33. Cosenza, E., Manfredi, G., Realfonzo, R., Behavior and modeling of bond of FRP rebars to concrete, J. Compos. Constr., 1997, 1(2): 40–5110.1061/(ASCE)1090-0268(1997)1:2(40) ↗
34. Comité Euro-International du Béton, CEB-FIP model code 1990: Design code, Thomas Telford Publishing; 1993
35. fédération internationale du béton/International Federation for Structural Concrete (fib), fib model code for concrete structures 2010, Ernst & Sohn Publishing; 2013
36. Huang, Z., Modelling the bond between concrete and reinforcing steel in a fire, Eng. Struct., 2010, 32(11): 3660–366910.1016/j.engstruct.2010.08.010 ↗
37. Lublóy, É., György, B.L., Temperature effects on bond between concrete and reinforcing steel, Zbornik radova Građevinskog fakulteta, Subotica, 2014, 30(26): 27–3510.14415/zbornikGFS26.03 ↗
38. Japan Society of Civil Engineers (JSCE), Recommendation for design and construction of concrete structures using continuous fibre reinforcing materials, Research Committee on Continuous Fiber Reinforcing Materials, Tokyo, Japan; 1997
39. El-Gamal, S., Bond strength of glass fiber-reinforced polymer bars in concrete after exposure to elevated temperatures, J. Reinf. Plast. Compos., 2014, 33(23): 2151–216310.1177/0731684414555408 ↗
40. Özkal, F.M., Polat, M., Yağan, M., Öztürk, M.O., Mechanical properties and bond strength degradation of GFRP and steel rebars at elevated temperatures, Constr. Build. Mater., 2018, 184: 45–5710.1016/j.conbuildmat.2018.06.203 ↗