journal article·2025-12-01Open access

Physical modelling and analytical evaluation of deformation zones in the extrusion of non-axisymmetric profiles

Beata Pawłowska

Materials Science-Poland· Volume 43· Issue 4

Abstract

Abstract This study investigates the effect of deformation zones on the extrusion load during the forming of non-axisymmetric profiles. Physical modelling using lead and analytical evaluation were performed for circular, square, triangular, and rectangular cross-sections at extrusion ratios ( λ ) of 3, 12, and 60. The results show that the maximum extrusion force ( F max ) increases significantly with both the depth of the plastic zone ( L pz ) and its volume ( V pz ), reaching up to 35–40% higher loads in non-axisymmetric sections than in circular ones at λ = 60. The dead zone height ( L dz ) and dead zone angle ( α dz ) also strongly influence the extrusion load, with F max increasing as L dz decreases and αdz increases. The study quantitatively relates these parameters to die geometry and demonstrates that optimising the deformation zone configuration can reduce extrusion force by up to 20%, leading to improved process efficiency and product quality. The developed analytical assessment provides a practical framework for integration into commercial extrusion simulation software to aid in process design and parameter selection.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Metallurgy and Material Forming · Metal Forming Simulation Techniques · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Materials Forming and Processing, Rzeszow University of Technology: Politechnika Rzeszowska im Ignacego Lukasiewicza , Rzeszow , Poland

References (36)

Show source-provided references
1. Liu, Z., Li, L., Fu, C., He, H., Li, B., Defects formation mechanism and precision control of exit flow, velocity in porthole die extrusion of hollow thin-walled aluminum profile, Chin. J. Nonferrous Met., 2021, 31(4): 917–930
2. Ma, Z., Shu, X., Xu, H., Wang, G., Tong, F., Li, Z., et al., Optimization of porthole extrusion die for 6063 aluminum alloy profile with thin-walled multicavity complex section and analysis of profile performance, Arch. Civ. Mech. Eng., 2024, 24(2): 85. 10.1007/s43452-024-00912-x10.1007/s43452-024-00912-x ↗
3. Nguyen, T.C., Truong, T.T., Wang, J.W.,·Sheu, J.J., Hsu, C.L., Hsu, Q.C., Analyzing and enhancing the porthole die design for extruding a complicated AA7005 profile, Int. J. Adv. Manuf. Technol., 2024, 134: 4803–4820. 10.1007/s00170-024-14439-110.1007/s00170-024-14439-1 ↗
4. Qian, D., Li, G., Deng, J., Wang, F., Effect of die structure on extrusion forming of thin-walled component with I-type longitudinal ribs, Int. J. Adv. Manuf. Technol., 2020, 108: 1959–1971. 10.1007/s00170-020-05490-910.1007/s00170-020-05490-9 ↗
5. Zhang, C., Zhao, G., Guan, Y., Gao, A., Wang, L., Li, P., Virtual tryout and optimization of the extrusion die for an aluminum profile with complex cross-sections, Int. J. Adv. Manuf. Technol., 2014, 78(5–8): 927–937. 10.1007/s00170-014-6691-910.1007/s00170-014-6691-9 ↗
6. Chen, H., Numerical simulation of extrusion process and die structure optimization for a hollow aluminum profile with thin wall, J. Mech. Eng., 2010, 46: 3410.3901/JME.2010.24.034 ↗
7. Liu, H., Liu, T., Chen, Z., Wang, H., Gao, K., Zhou, Z., et al., Optimization on extrusion process for large reinforced thin-walled aluminum profile based on experimental design and response surface method, Forg. Stamp. Technol., 2022, 47: 144–152
8. Kathirgamanathan, P., Neitzert, T., Optimization of pocket design to produce a thin shape complex profile, Prod. Eng., 2009, 3: 231–241. 10.1007/s11740-009-0161-510.1007/s11740-009-0161-5 ↗
9. Ji, H., Nie, H., Chen, W., Ruan, X., Pan, P., Zhang, J., Optimization of the extrusion die and microstructure analysis for a hollow aluminum alloy profile, Int. J. Adv. Manuf. Technol., 2017, 93: 3461–3471. 10.1007/s00170-017-0720-410.1007/s00170-017-0720-4 ↗
10. Jo, H.H., Lee, S.K., Jung, C.S., Kim, B.M., A non-steady state FE analysis of Al tubes hot extrusion by a porthole die, J. Mater. Process. Technol., 2006, 173: 223–231. 10.1016/j.jmatprotec.2005.03.03910.1016/j.jmatprotec.2005.03.039 ↗
11. Zhang, C., Zhao, G., Chen, Z., Chen, H., Kou, F., Effect of extrusion stem speed on extrusion process for a hollow aluminum profile, Mater. Sci. Eng., 2012, 177: 1691–1697. 10.1016/j.mseb.2011.09.04110.1016/j.mseb.2011.09.041 ↗
12. Chen, L., Zhao, G., Yu, J., Effects of ram velocity on pyramid die extrusion of hollow aluminum profile, Int. J. Adv. Manuf. Technol., 2015, 79: 2117–2125. 10.1007/s00170-015-7059-510.1007/s00170-015-7059-5 ↗
13. Gordon, W.A., Van Tyne, C.J., Moon, Y.H., Axisymmetric extrusion through adaptable dies – Part 1: flexible velocity fields and power terms, Int. J. Mech. Sci., 2007, 49: 104–115. 10.1016/j.ijmecsci.2006.07.01110.1016/j.ijmecsci.2006.07.013 ↗
14. Kar, P.K., Sahoo, S.K., Das, N.S., Upper bound analysis for extrusion of t-section bar from square billet through square dies, Meccanica, 2000, 35: 399–410. 10.1023/A:101036171157910.1023/A:1010361711579 ↗
15. Mohammed, R.J., Effect of die angle on stress distribution in extrusion process of aluminum rod, Basrah J. Eng. Sci., 2014, 14(2): 43–50. http://un.uobasrah.edu.iq/papers/4080.pdf.
16. Yang, D.Y., Park, K., Kang, Y.S., Integrated finite element simulation for the hot extrusion of complicated Al alloy profiles, J. Mater. Process. Technol., 2001, 111: 25–30. 10.1016/S0924-0136(01)00513-110.1016/S0924-0136(01)00513-1 ↗
17. Qamar, S.Z., Arif, A.F.M., Sheikh, A.K., A new definition of shape complexity for metal extrusion, J. Mater. Process. Technol., 2004, 155–156: 1734–1739. 10.1016/j.jmatprotec.2004.04.16310.1016/j.jmatprotec.2004.04.163 ↗
18. Xu, X., Jiang, F., Li, J., Huang, H., Jiang, C., Multi-objective optimization of a multi-cavity, significant wall thickness difference extrusion profile mold design for new energy vehicles, Materials, 2024, 17: 2126. 10.3390/ma1709212610.3390/ma17092126 ↗
19. Zhang, C., Wen, M., Zhao, G., Chen, L., Sun, W., Bai, K., One-time determination of 20 material parameters in a strain-compensated constitutive model and its application in extrusion for an Al-Zn-Mg thin-walled profile, Thin-Walled Struct., 2019, 135: 65–77. 10.1016/j.tws.2018.10.03410.1016/j.tws.2018.10.034 ↗
20. Zhao, H., Wang, H.N., Wang, M.J., Li, G.Y., Simulation of extrusion process of complicated aluminium profile and die trial, Trans. Nonferrous Met. Soc. China, 2012, 22(7): 1732–1737. 10.1016/S1003-6326(11)6138010.1016/S1003-6326(11)61380-0 ↗
21. Zhang, C., Zhao, G., Chen, H., Guan, Y., Cai, H., Gao, B., Investigation on effects of die orifice layout on three-hole porthole extrusion of aluminum alloy 6063 tubes, J. Mater. Eng. Perform., 2012, 22: 1223–1232. 10.1007/s11665-012-0405-y10.1007/s11665-012-0405-y ↗
22. Selvaggio, A., Donati, L., Reggiani, B., Haase, M., Dahnke, C., Schwane, M., et al., Scientific Benchmark 2015: Effect of choking and bearing length on metal flow balancing in extrusion dies, Mater. Today: Proc., 2015, 2: 4704–4713. 10.1016/j.matpr.2015.10.00310.1016/j.matpr.2015.10.003 ↗
23. Karami, P., Abrinia, K., Saghafi, B., A new analytical definition of the dead material zone for forward extrusion of shaped sections, Meccanica, 2014, 49: 295–304. 10.1007/s11012-013-9794-810.1007/s11012-013-9794-8 ↗
24. Eivani, A.R., Karimi Taheri, A., The effect of dead metal zone formation on strain and extrusion force during equal channel angular extrusion, Compos. Mater. Sci., 2008, 42: 14–20. 10.1016/j.commatsci.2007.06.00110.1016/j.commatsci.2007.06.001 ↗
25. Qamar, S.Z. FEM study of extrusion complexity and dead metal zone, Arch. Mater. Sci. Eng., 2009, 36(2): 110–117
26. Li, S., Bourke, M.A.M., Beyerlein, I.J., Alexander, D.J., Clausen, B., Finite element analysis of the plastic deformation zone and working load in equal channel angular extrusion, Mater. Sci. Eng. A, 2004, 382: 217–236. 10.1016/j.msea.2004.04.06710.1016/j.msea.2004.04.067 ↗
27. Zhang, D., Xu, H., Xu, S., Tong, F., Chen, K., Li, Z., et al., Metal flow behavior and energy consumption model during the extrusion process of a 6063 aluminum alloy profile with complex cross-section, J. Mater. Res. Technol., 2024, 33: 9911–9925. 10.1016/j.jmrt.2024.12.02910.1016/j.jmrt.2024.12.029 ↗
28. Qamar, S.Z., Pervez, T., Effect of process parameters on metal flow and dead metal zone in extrusion, Arch. Mater. Sci., 2007, 28(1–4): 118–123
29. Qamar, S.Z., Chekotu, J.C.H., Qamar, S.B., Effect of shape complexity on ram pressure and metal flow in aluminum extrusion the minerals, Met. & Mater. Soc., 2019, 71: 12. 10.1007/s11837-019-03748-610.1007/s11837-019-03748-6 ↗
30. Lof, J., Blokhuis, Y., FEM simulations of the extrusion of complex thin-walled aluminum sections, J. Mater. Process. Technol., 2002, 122: 344–354. 10.1016/S0924-0136(01)01266-310.1016/S0924-0136(01)01266-3 ↗
31. Abrinia, K., Ghorbani, M., Theoretical and experimental analyses for the forward extrusion of nonsymmetric sections, Mater. Manuf. Process., 2012, 27: 420–429. 10.1080/10426914.2011.57786910.1080/10426914.2011.577869 ↗
32. Qamar, S.Z., Shape complexity, metal flow, and dead metal zone in cold extrusion, Mater. Manuf. Process., 2010, 25: 1454–1461. 10.1080/10426914.2010.51265010.1080/10426914.2010.512650 ↗
33. Liu, Y., Wang, T., Wang, Z., Huang, Q., Mathematical modeling and analysis of the tailor rolled blank manufacturing process, Int. J. Mech. Sci., 2024, 266: 108991. 10.1016/j.ijmecsci.2024.10899110.1016/j.ijmecsci.2024.108991 ↗
34. Wang, Z., Li, J., Liu, X., Zhang, S., Lin, Y., Tan, J., Diameter-adjustable mandrel for thin-wall tube bending and domain knowledge-integrated optimization, Eng. Appl. Artif. Intell., 2025, 139: 109634. 10.1016/j.engappai.2024.10963410.1016/j.engappai.2024.109634 ↗
35. Yao, S., Chen, Y., Sun, C., Zhao, N., Wang, Z., Zhang, D., Dynamic response mechanism of thin-walled plate under confined and unconfined blast loads, J. Mar. Sci. Eng., 2024, 12(2): 224. 10.3390/jmse1202022410.3390/jmse12020224 ↗
36. Zhang, Z., Wan, L., Wen, Q., Shi, Y., Feng, Z., Wire-based friction stir additive manufacturing of TiC reinforced Al-Cu-Mg composite: Particle refinement and dispersion, Compos. Part. A, 2025, 196: 109009. 10.1016/j.compositesa.2025.10900910.1016/j.compositesa.2025.109009 ↗