journal article·2025-09-01Open access

Experimental accuracy verification of the common practice analysis of doubly reinforced shallow concrete beams reinforced by steel grade 500

Hassan M. Magbool, Ahmed A. El-Abbasy

Materials Science-Poland· Volume 43· Issue 3

Abstract

Abstract Beam designers typically use only tension reinforcement. A beam’s moment strength can be increased either by increasing the tension reinforcement area or by increasing the beam depth. However, when architectural or functional constraints limit the beam’s cross-section, a compression reinforcement is added to enhance moment strength. This study aims to assess the validity of the accuracy analysis and design methods for doubly reinforced sections as suggested by various provisions and codes. The study conducted an experimental investigation involving three beams, each with a compression steel to tension steel ratio of 0.2, 0.3, and 1. Furthermore, this study aims to develop a proposed analytical method for the design of doubly reinforced shallow beams utilizing grade 500 steel. The experimental results showed that all beams failed at a compression strain in concrete approximately equal to 0.0015, which is almost one-half of that recommended in most codes. It was clear that using steel grade 500 in doubly reinforced beams of shallow depths requires a high percentage of compression reinforcement to avoid compression-controlled failure, which is uneconomic compared with increasing concrete dimensions. The conventional analysis of such sections is not reasonable; therefore, the proposed analytical method effectively predicted the experimental values of the ultimate load and maximum bending moment of the beam with acceptable accuracy, exhibiting an error of approximately 11%.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Structural Behavior of Reinforced Concrete · Structural Load-Bearing Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Civil and Architectural Engineering Department, College of Engineering and Computer Science, Jazan University , Jazan , Saudi Arabia

References (37)

Show source-provided references
1. Shariat, M., Shariati, M., Madadi, A., Wakil, K., Computational Lagrangian Multiplier Method by using for optimization and sensitivity analysis of rectangular reinforced concrete beams, Steel Compos. Struct., 2018, 29: 243–256
2. Reynolds, C.E., Steedman, J.C., Threlfall, A.J., Reinforced concrete designer’s handbook, CRC Press, USA, 2007
3. ACI 318M-14, Building code requirements for structural concrete (ACI 318M-14): an ACI Standard: Commentary on building code requirements for structural concrete (ACI 318M-14), American Concrete Institute, USA, 2015
4. Saini, B., Sehgal, V.K., Gambhir, M.L., Genetically optimized artificial neural network based optimum design of singly and doubly reinforced concrete beams, Asian J. Civ. Eng., 2006, 7(6): 603–619
5. Jabbar, A.M., Hasan, Q.A., Abdul-Husain, Z.A., A theoretical study to predict the flexural strength of singly and doubly reinforced ultra-high performance concrete beams, J. Eng. Sci. Technol. Rev., 2022, 15: 91–10110.25103/jestr.152.13 ↗
6. Bhalchandra, S.A., Adsul, P.K., Cost optimization of doubly reinforced rectangular beam section, Int. J. Mod. Eng. Res., 2012, 2: 3939–3942
7. Manjunath, H.R., Kavya, K.R., Rao, K., Prakash, M.R., Prabhakara, R., Analysis of flexural behaviour of singly and doubly reinforced high strength concrete beams using ANSYS, In Proceedings of International Conference on Advances in Architecture and Civil Engineering (AARCV 2012), 2012, p. 179
8. Galeb, A.C., Optimum design of doubly reinforced concrete beams using simulated annealing, Int. J. Civ. Eng. Technol. (IJCIET), 2018, 9: 61–70
9. Wight, J.K., Reinforced concrete: Mechanics and design, 8th ed., Prentice Hall, Upper Saddle River, NJ, 2022
10. Tahwia, A.M., Noshi, A., Abdellatief, M., Matthana, M.H., Experimental investigation of rubberized concrete slab-on-grade containing tire-recycled steel fibers, Innovative Infrastruct. Solut., 2024, 9: 4610.1007/s41062-023-01354-9 ↗
11. Handousa, A.M., Abdellatief, M., Salem, F.A., Mahmoud, N., Ghannam, M., Experimental and analytical study on axial behaviour of square corrugated concrete filled single and double skin tube stub columns, Sci. Rep., 2025, 15: 216710.1038/s41598-025-85585-z ↗
12. Eurocode 2: Design of concrete structures–part 1, Eurocode 2: Design of concrete structures-part 1–1: General rules and rules for buildings, Eur. Comm. Standard. Bruss., 2004, 668: 668
13. CSA, Design of concrete structures, A23.3-04, Canadian Standards Association, Canada, 2004
14. SBC, The Saudi Building Code for concrete structures and commentary, The Saudi Building Code National Committee (SBCNC), Riyadh, KSA, 2018
15. ECP (Egyptian Code of Practice), The Egyptian Code for the Design and Construction of Concrete Structures, Housing and Building National Research Center, Giza, Egypt, 2020
16. Hassoun, M.N., Al-Manaseer, A., Structural concrete: theory and design, John Wiley & Sons, USA, 2020
17. Darwin, D., Dolan, C.W., Nilson, A.H., Design of concrete structures, McGraw-Hill Education, New York, NY, USA, 2016
18. Ghoneim, M., EI-Mihilmy, M., Design of reinforced concrete structures, 2nd ed., Cairo University, Giza, Egypt, 2008
19. Bhatt, P., MacGinley, T., Choo, B., Reinforced concrete design to Eurocodes, CRC Press, USA, 201410.1201/b15266 ↗
20. Toniolo, G., Di Prisco, M., Reinforced concrete design to eurocode 2, Springer, Switzerland, 201710.1007/978-3-319-52033-9 ↗
21. Issa, M.S., El-Abbasy, A.A., Examples oriented reinforced concrete text book according to ACI318, Dar Elmaarefa, Cairo, Egypt, 2019
22. Al Hazmi, H.S.J., El-Abbasy, A.A., Abou Elmal, H.S., Applying Saudi Building Code (SBC 304) in teaching reinforced concrete courses in Jazan University, International Conference on Engineering Education (ICEE), Madinah, Kingdom of Saudi Arabia, 2011
23. Nirusha, D.S., Prasad, R., Prediction of percentage of steel for singly and doubly reinforced beam sections using artificial neural network, Glob. J. Eng. Appl. Sci., 2011, 1: 127–129
24. Yousif, S.T., ALsaffar, I.S., Ahmed, S.M., Optimum design of singly and doubly reinforced concrete rectangular beam sections: Artificial neural networks application, Iraqi J. Civ. Eng., 2010, 6: 1–1910.37650/ijce.2010.14126 ↗
25. Panjehpour, P., Sorooshian, S., Deepak, T.J., The threshold for under-reinforced concrete sections proposed by ACI 318, EC 2 and BS 8110, Civ. Eng. Archit., 2021, 9: 1754–1758. 10.13189/cea.2021.09060910.13189/cea.2021.090609 ↗
26. El-Abbasy, A.A., Integrated interaction diagrams for sections subjected to axial force and bending moment according to the American Concrete Institute and the Saudi Building Code, Arab. J. Sci. Eng., 2021, 46: 4577–459210.1007/s13369-020-04976-8 ↗
27. ASTM C39, Test method for compressive strength of cylindrical concrete specimens, ASTM International, USA, 2017. 10.1520/C0039_C0039M-17B
28. S.-E. CEN, Cement-Part 1: Composition, specifications and conformity criteria for common cements, European Commitee for Standarization, Brussels, 2011
29. S.E. CEN, Methods of testing cement – Part 1: Determination of strength, Vol. 169, European Commitee for Standarization, Brussels, 2005, p. 36
30. ASTM A572, Specification for high-strength low-alloy Columbium-Vanadium structural steel, ASTM International, USA, 2015. 10.1520/A0572_A0572M-15
31. ASTM C31, Practice for making and curing concrete test specimens in the field, ASTM International, USA, 2017. 10.1520/C0031_C0031M-17
32. ACI 308R-01 R08, Guide to curing concrete, American Concrete Institute, Farmington Hills, MI, USA, 2008
33. Pauw, A., Static modulus of elasticity of concrete as affected by density, ACI J. Proc., 1960, 57(6): 679–68310.14359/8040 ↗
34. American Concrete Institute, Report on high-strength concrete (ACI 363R-10), ACI Committee 363, Farmington Hills, Michigan, USA, 2010
35. Kaar, P.H., Hanson, N.W., Capell, H.T., Stress–strain characteristics of high-strength concrete, Spec. Publ., 1978, 55: 161–186
36. Hognestad, E., Hanson, N.W., McHenry, D., Concrete stress distribution in ultimate strength design, In Journal Proceedings, 1955, pp. 455–480
37. Popovics, S., A review of stress–strain relationships for concrete, In Journal Proceedings, 1970, pp. 243–248