journal article·2024-03

Investigation on effects of thermo-mechanical coupling on residual stress in lithium niobate in surface acoustic wave device

Peng Yu, Shenghua Huang, Zhaoyong Ren, Jiantao Liu, Yijie Liu

Publisher page

Abstract

Surface acoustic w ave (SAW) devices are subject to thermomechanical coupling during operation, and when the temperature rises sharply to 180 °C, the surface of the lithium niobate crystal substrate generates nonuniform thermal stresses, thus leaving large residual stresses after complete cooling, which seriously influences its service performance and life. In this study, the thermal residual stresses of lithium niobate wafers were tested by nanoindentation tests, and the nanoindentation test process was simulated. The inverse calculation of the parameters of the lithium niobate constitutive model was carried out by comparing the load-displacement curves obtained from the finite element calculations with the experimental results. A multiscale model of the SAW device was established, its operation process was simulated, and then the generation law of residual stress was further discussed. The nanoindentation test results show that the thermal residual stress is positively correlated with the heating time under the effect of the same temperature; however, at the heating temperature up to about 180 °C, the lithium niobate crystal enters the high-temperature hyperelastic interval, and the yield stress of the crystal increases significantly at this stage. The constitutive model curves obtained by finite element calculations are in good agreement with the experimental results, and the thermal residual stress value of lithium niobate can reach 2/3 of its yield stress outside the high-temperature hyperelastic interval by comparison tests. The calculation results of the multi-scale model of the SAW device indicate that excessive thermal stress is the main cause of damage during the thermo-mechanical coupling of the SAW device. The polarization direction of lithium niobate crystals may cause the development of damage cracks, increasing the heat dissipation can effectively reduce the thermal stress to which it is subjected, and better extend the service life of the SAW device.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metal and Thin Film Mechanics · Surface Treatment and Residual Stress · Advanced Surface Polishing Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (30)

Show source-provided references
1. Pan · 2018
2. Stoichiometric lithium niobate crystals: towards Identifiable Wireless surface acoustic wave sensors operable up to 600 °C10.1109/LSENS.2019.2908691 ↗
3. Innovative NiAl electrodes for long-Term, Intermediate high-temperature SAW sensing applications using LiNbO3 substrates10.1109/JSEN.2023.3289008 ↗
4. Residual stress measurement in veneering ceramic by hole-drilling10.1016/j.dental.2010.12.002 ↗
5. Applications of the strain gauge for determination of residual stresses using Ring-core method10.1016/j.proeng.2012.09.531 ↗
6. Investigation of through thickness residual stress distribution in equal channel angular rolled Al 5083 alloy by layer removal technique and X-ray diffraction10.1016/j.matdes.2012.03.029 ↗
7. X-ray diffraction analysis of three-dimensional residual stress fields reveals origins of thermal fatigue in uncoated and coated steel10.1016/j.scriptamat.2010.02.006 ↗
8. Neutron diffraction and finite element modeling to study the weld residual stress relaxation induced by cutting10.1016/j.matdes.2013.04.053 ↗
9. Residual stress characterization of Al/SiC nanoscale multilayers using X-ray synchrotron radiation10.1016/j.tsf.2010.08.148 ↗
10. Using finite element and ultrasonic method to evaluate welding longitudinal residual stress through the thickness in austenitic stainless steel plates10.1016/j.matdes.2012.09.038 ↗
11. Determination of welding residual stress distribution in API X65 pipeline using a modified magnetic Barkhausen noise method10.1016/S0308-0161(03)00131-5 ↗
12. An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments10.1557/JMR.1992.1564 ↗
13. A new method for estimating residual stresses by instrumented sharp indentation10.1016/S1359-6454(98)00226-2 ↗
14. Plastic deformation of LiNbO3 single crystals10.1051/rphysap:0198700220110135300 ↗
15. Nanoindentation of lithium niobate: hardness anisotropy and pop-in phenomenon10.1016/j.msea.2004.11.027 ↗
16. Strength distribution and fracture analyses of LiNbO3 and LiTaO3 single crystals under biaxial loading10.1016/j.jeurceramsoc.2017.02.002 ↗
17. Ramli · 2011 · 1
18. Finite element simulation of 128°YX-LiNbO3 surface acoustic wave resonator
19. A package-less SAW RFID sensor concept for structural health monitoring10.1080/15376494.2019.1579397 ↗
20. Growth of piezoelectric and ferroelectric materials by the CzochraIski technique10.1111/j.1151-2916.1965.tb11814.x ↗
21. Application of Czochralski method for growth of LiNbO 3, LiTaO 3, and NaNbO 3 single crystals
22. Deformation and stress at pop-in of lithium niobate induced by nanoindentation10.1016/j.scriptamat.2014.01.018 ↗
23. 3D finite element simulation of the nanoindentation process
24. An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments10.1557/JMR.1992.1564 ↗
25. Behavior of Al/Cu/Ti electrodes in surface acoustic wave filter at high power10.1016/j.cap.2019.01.001 ↗
26. Computational modeling of the forward and reverse problems in instrumented sharp indentation10.1016/S1359-6454(01)00295-6 ↗
27. High-temperature superelasticity in CoNiGa, CoNiAl, NiFeGa, and TiNi monocrystals10.1007/s11182-009-9143-5 ↗
28. Shape memory effect and high-temperature superelasticity in high-strength single crystals10.1016/j.jallcom.2012.02.003 ↗
29. Indentation modulus of elastically anisotropic half spaces10.1080/01418619308224756 ↗
30. Single crystal elastic constants and calculated aggregate properties