journal article·2025-03

Optimization of picosecond laser machining parameters for monocrystalline silicon based on Box-Behnken Design

Zhe Li, Chuanzhen Huang, Zhen Wang, Zhenyu Shi, Longhua Xu, Shuiquan Huang, Meina Qu, Zhengkai Xu, Dijia Zhang, Baosu Guo, Hanlian Liu, Dun Liu, Peng Yao

Publisher page

Abstract

The aim of the study was to utilize the “cold machining” characteristic of picosecond laser for low-damage and high-efficiency machining of monocrystalline silicon cavities. Box-Behnken Design (BBD) was employed to systematically analyze the impact of four significant machining parameters including laser energy, hatch width, repetition frequency and scan speed on the machining results. Statistical models and response plots were generated for four response variables including surface roughness ( Sa), heat-affected zone width ( HAZ), degree of oxidation ( DOO) and material removal rate ( MRR). Furthermore, the optimal machining parameters based on four different low-damage and high-efficiency objectives were predicted. The simulation results of the temperature distribution under single pulse laser ablation and laser scanning ablation on silicon were obtained. The results demonstrate that the regression models can accurately predict Sa, HAZ, and MRR with errors below 10 %. The optimized machining parameters can enable highly efficient, characterized by an MRR exceeding 0.899 mm 3/min, and nearly thermal damage-free machining of silicon cavities, characterized by a Sa of 0.564 μm, a HAZ of 16.71 μm, a DOO of 8.4 %, a submicron damage depth, and no evident phase transition. Additionally, the removal mechanisms of monocrystalline silicon machining by picosecond laser were primarily spallation at both low and high energy and phase explosion at high energy. These results validate the reliability and feasibility of employing BBD for modeling, predicting, and optimizing laser machining parameters. Overall, this study offers a reliable approach and a solid theoretical basis in optimizing machining parameters in the picosecond laser machining of monocrystalline silicon.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Laser Material Processing Techniques · Advanced Surface Polishing Techniques · Ocular and Laser Science Research

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (40)

Show source-provided references
1. Laser-ablated silicon in the frequency range from 0.1 to 4.7 THz10.1109/TTHZ.2019.2939554 ↗
2. Two-step femtosecond laser etching for bulk micromachining of 4H–SiC membrane applied in pressure sensing10.1016/j.ceramint.2022.01.100 ↗
3. Micromachined membrane structures for pressure sensors based on AlGaN/GaN circular HEMT sensing device10.1016/j.mee.2012.06.014 ↗
4. Silicon kinoform cylindrical lens with low surface roughness for high-power terahertz radiation10.1016/j.optlastec.2019.105953 ↗
5. Large-area femtosecond laser milling of silicon employing trench analysis10.1016/j.optlastec.2020.106866 ↗
6. Anti-reflection silicon with self-cleaning processed by femtosecond laser10.1016/j.optlastec.2020.106790 ↗
7. Picosecond laser ablation for silicon micro fuel cell fabrication10.1088/0960-1317/23/5/055021 ↗
8. Research on microhole processing technology based on the femtosecond-laser spiral trepanning method10.3390/app10217508 ↗
9. Surface modeling and component analysis of picosecond laser ablation of CVD diamond10.1016/j.diamond.2020.108191 ↗
10. One-step femtosecond laser irradiation of single-crystal silicon: evolution of micro-nano structures and damage investigation10.1016/j.matdes.2022.111443 ↗
11. Femtosecond laser single step, full depth cutting of thick silicon sheets with low surface roughness10.1016/j.optlastec.2020.106899 ↗
12. High-quality high-throughput silicon laser milling using a 1 kW sub-picosecond laser10.1364/OL.411412 ↗
13. Optimization strategy for high-quality laser milling of silicon10.1016/j.optlastec.2022.107921 ↗
14. Picosecond laser micromachining of silicon wafer: characterizations and electrical properties10.1142/S0218625X19501427 ↗
15. Precise drilling of steel with ultrashort pulsed solid state lasers10.1117/12.515612 ↗
16. Fabrication of high-aspect-ratio grooves with high surface quality by using femtosecond laser10.1108/ILT-11-2020-0432 ↗
17. The preliminary study based on milling dental glass ceramics with visible and infrared picosecond laser pulse10.1007/s00170-019-04601-5 ↗
18. Investigations on 355 nm picosecond laser machining of carbon fiber reinforced polymer composites10.1016/j.jmapro.2023.06.036 ↗
19. Experimental investigation and optimization on trepanning drilling in K24 superalloy by femtosecond laser via orthogonal experiment10.1007/s00170-023-12157-8 ↗
20. Optimization of operating conditions to maximize PEMFC performance by orthogonal test method and RSM
21. Enhanced production of an Anti-Cancer pigment from Bacillus endophyticus JUPR15: single factor system vs RSM10.5958/0974-360X.2021.00027.5 ↗
22. Simulation analysis and optimization of laser preheating SiC ceramics based on RSM10.1016/j.ijthermalsci.2022.108070 ↗
23. Modeling and optimizing femtosecond laser process parameters for high-efficient and near damage-free micromachining of single-crystal GaN substrate10.1016/j.mssp.2022.107123 ↗
24. Predictive models based on RSM and ANN for roughness and wettability achieved by laser texturing of S275 carbon steel alloy10.1016/j.optlastec.2023.109963 ↗
25. Parametric optimization of hole taper control in ultraviolet nanosecond laser micro-drilling of copper foil10.1016/j.optlastec.2023.109706 ↗
26. Self-organized fractal-like structures formation on the silicon wafer surface using the femtosecond laser pulses10.1016/j.optlaseng.2020.106008 ↗
27. Low surface damage laser processing of silicon by laser-induced plasma etching (LIPE)10.1016/j.apsusc.2022.153712 ↗
28. Electron emission from metal surfaces exposed to ultrashort laser pulses
29. Electric field analysis coupled with the two-temperature model to elucidate the generation process of laser-induced periodic surface structure10.1016/j.jmatprotec.2022.117601 ↗
30. Theoretical and experimental investigations of ultra-short pulse laser interaction on Ti6Al4V alloy10.1016/j.jmatprotec.2018.08.028 ↗
31. Laser damage in silicon: energy absorption, relaxation, and transport10.1063/1.4891633 ↗
32. The preliminary study based on milling dental glass ceramics with visible and infrared picosecond laser pulse10.1007/s00170-019-04601-5 ↗
33. Large-area femtosecond laser milling of silicon employing trench analysis10.1016/j.optlastec.2020.106866 ↗
34. Photomechanical spallation of molecular and metal targets: molecular dynamics study10.1007/s00339-004-2682-2 ↗
35. Limit of overheating and the threshold behavior in laser ablation10.1103/PhysRevE.68.041501 ↗
36. Numerical simulation and experimental study on picosecond laser ablation of stainless steel10.1016/j.optlastec.2020.106150 ↗
37. Raman microspectroscopy study of processing-induced phase transformations and residual stress in silicon10.1088/0268-1242/14/10/310 ↗
38. Effects of deep subsurface damages on surface nanostructure formation in laser recovery of grinded single-crystal silicon wafers10.1016/j.precisioneng.2019.12.005 ↗
39. Physical insight in the fluence-dependent distributions of Au nanoparticles produced by sub-picosecond UV pulsed laser ablation of a solid target in vacuum environment10.1016/j.apsusc.2019.02.022 ↗
40. Short-pulse laser ablation of solids: from phase explosion to fragmentation10.1103/PhysRevLett.91.225502 ↗