journal article·2023-11

3D-hexagonhelical TiO2-monoliths: Design, printing process and solar photoactivity

Fabiola Méndez-Arriaga, Mariel Rodríguez-Hernández, Rafael Almanza

Publisher page

Abstract

Solid 3D titanium dioxide (TiO 2 ) structures with hexagonhelical (3DHH) geometry were possible to achieve through additive printing technology. The monoliths acquired the shape and hydrodynamic requirements of a tubular solar CPC photoreactor. The optimum printing parameters were achieved with a 1.2 mm ∅ nozzle, and a dosing rate of 0.87 ml/min, with a duration of 10 min per complete manufactured piece. The heat treatment (T am⇨180°C 30 min ⇨250°C 30 min ⇨350°C 30 min ) applied to the printed pieces does not modify the active anatase/rutile weight ratio (82.9/17.1). On the contrary, the mechanical resistance improved remarkably after the heat treatment: a compressive stress 5 folds higher (307.81 ± 15.31 kPa) was observed in comparison with the pieces without heat treatment. The most important shrinkage in diameter and height are generated throughout the dehumidification process at room temperature of free drying for 24 h (Δ∅ = 3.86 ± 0.43 mm and Δ h = 3.78 ± 0.16 mm respectively). In contrast, the size changes were insignificant after heat treatment (Δ∅ = 0.075 ± 0.12 mm and Δ h = 0.15 ± 0.01 mm). The microscopic morphology shows changes on the surface of the monoliths with deagglomerated flat shapes after heat treatment. Persistent degradation of the IBP model compound was observed over 10 cycles under solar irradiation in a laboratory-scale photoreactor using twelve heat-pretreated 3DHH-TiO 2 monoliths. In addition, 10 cycles were compared for monoliths without thermal processing. Including both cases (monoliths with and without heat treatment), 90% of the solar experiments degraded between 50 and 95% of the initial IBP concentration per cycle (200 mg/L). The resistance to erosion acquired by heat treatment allows mechanical stability for photocatalytic purposes while maintaining significant solar activity. The commercial use of heterogeneous photocatalytic processes on an industrial scale could soon be achieved with the support of 3D additive manufacturing.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Additive Manufacturing and 3D Printing Technologies · TiO2 Photocatalysis and Solar Cells · Bone Tissue Engineering Materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (32)

Show source-provided references
1. Web · 2023
2. Engineering and modeling perspectives on photocatalytic reactors for water treatment10.1016/j.watres.2021.117421 ↗
3. A comprehensive review on reactive oxygen species (ros) in advanced oxidation processes (aops)
4. Antibiotics degradation by advanced oxidation process (aops): recent advances in ecotoxicity and antibiotic-resistance genes induction of degradation products10.1016/j.chemosphere.2022.136977 ↗
5. Tio2 3d structures for environmental purposes by additive manufacturing: photoactivity test and reuse10.1016/j.mssp.2019.04.034 ↗
6. Additive manufacturing: technology, applications and research needs10.1007/s11465-013-0248-8 ↗
7. Review of 3d printing in photocatalytic substrates and catalysts
8. Fabrication of zno periodic structures by 3d printing10.1016/j.jeurceramsoc.2016.05.025 ↗
9. Three-dimensional printing in catalysis: combining 3d heterogeneous copper and palladium catalysts for multicatalytic multicomponent reactions10.1021/acscatal.7b02592 ↗
10. Environmentally friendly engineering and three-dimensional printing of tio2 hierarchical mesoporous cellular architectures10.1021/acssuschemeng.7b02450 ↗
11. 3d structured nanocomposites by fdm process: a novel approach for large-scale photocatalytic applications
12. Additive manufacturing of polymer-derived titania for one-step solar water purification10.1016/j.mtcomm.2018.02.010 ↗
13. 3d printed hierarchical gyroid structure with embedded photocatalyst tio2 nanoparticles10.1089/3dp.2017.0033 ↗
14. 3d-printed grids with polymeric photocatalytic system as flexible air filter10.1016/j.apcatb.2019.118307 ↗
15. Solar photocatalytic disinfection using ink-jet printed composite tio2/sio2 thin films on flexible substrate: applicability to drinking and marine water10.1016/j.solener.2019.09.038 ↗
16. The chemical, mechanical, and physical properties of 3d printed materials composed of tio(2)-abs nanocomposites10.1080/14686996.2016.1152879 ↗
17. 3d printing of structured nanotitania catalysts: a novel binder-free and low-temperature chemical sintering method10.1089/3dp.2017.0164 ↗
18. High photocatalytic efficiency of inkjet printed patterns by formulation of eco-friendly tio2-based inks
19. Mendez-Arriaga · 2018
20. Tio2 photocatalyst for indoor air remediation: influence of crystallinity, crystal phase, and uv radiation intensity on trichloroethylene degradation10.1016/j.apcatb.2009.08.003 ↗
21. Novel ZnO photocatalysts for pollutants' abatement under solar radiation at pilot plant scale
22. 2023
23. Anatase/rutile tio2 composites: influence of the mixing ratio on the photocatalytic degradation of malachite green and orange ii inslurry10.1016/j.matchemphys.2007.05.035 ↗
24. 3d printed microstructured Au/TiO2 catalyst for hydrogen photoproduction10.1016/j.apmt.2019.06.007 ↗
25. Evaluation of the anatase/rutile phase composition influence on the photocatalytic performances of mesoporous TiO2 powders10.1016/j.ijhydene.2015.05.180 ↗
26. Enhanced photocatalytic performance of tio2 particles via effect of anatase–rutile ratio10.1016/j.physe.2014.11.006 ↗
27. What is degussa (evonik) P25? crystalline composition analysis, reconstruction from isolated pure particles and photocatalytic activity test10.1016/j.jphotochem.2010.07.024 ↗
28. Preparation and characterization of porous titania ceramic scaffolds
29. The influence of thermal treatment conditions on the properties of tio ceramics10.1260/1708-5284.11.2.131 ↗
30. Quantitative analysis of anatase-rutile mixtures with an x-ray diffractometer10.1021/ac60125a006 ↗
31. Oxygen vacancy induced structural phase transformation in tio2 nanoparticles10.1088/0022-3727/42/20/205101 ↗
32. Characteristics and properties of a novel in situ method of synthesizing mesoporous tio2 nanopowders by a simple coprecipitation process without adding surfactant10.1016/j.jallcom.2014.05.227 ↗