Study of subsurface damage during nano-grinding of B3-GaN using molecular dynamics simulations
Source abstract
Abstract
The mechanism of subsurface damage formation during zinc blende gallium nitride (B3-GaN) nano-grinding was investigated using molecular dynamics (MD). The effects of grinding depth and abrasive radius on the grinding force, temperature, potential energy, phase transition, dislocations, the average coefficient of friction (COF), material removal rate (MRR) and subsurface damage were systematically investigated. The results show that dislocations, amorphization and wurtzite (B4) phase transitions are the primary defects present in the subsurface damage layer. Dislocation nucleation and proliferation are the main mechanisms aggravating the subsurface damage, and the 1/2<110> perfect dislocation along the <110> slip direction predominates in the dislocation. Grinding forces, temperature, potential energy, amorphous atoms, B4 phase atoms and dislocations increase with increasing grinding depth, exacerbating the subsurface damage of B3-GaN. As the abrasive radius increases, the amorphous atoms increase and then decrease, with the B4 phase atoms gradually reducing. The rest of the above parameters increase gradually, exacerbating the subsurface damage of B3-GaN. Furthermore, a smaller grinding depth and abrasive radius result in better machining accuracy, but decrease MRR. A technical reference for the ultra-precise and low-damage processing of B3-GaN can be provided by this study.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metal and Thin Film Mechanics · Diamond and Carbon-based Materials Research · Semiconductor materials and devices
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (53)
Show source-provided references
1. A survey of wide bandgap power semiconductor devices10.1109/TPEL.2013.2268900 ↗
2. An overview of normally-off GaN-based high el Roccaforte ectron mobility transistors10.3390/ma12101599 ↗
3. A survey of gallium nitride HEMT for RF and high power applications10.1016/j.spmi.2017.05.042 ↗
4. GaN-based RF power devices and amplifiers10.1109/JPROC.2007.911060 ↗
5. Group III nitride and SiC based MEMS and NEMS: materials properties, technology and applications10.1088/0022-3727/40/20/S19 ↗
6. Off-state electrical breakdown of AlGaN/GaN/Ga(Al)N HEMT heterostructure grown on Si(111)
7. Highly efficient GaN-based high-power flip-chip light-emitting diodes10.1364/OE.27.00A669 ↗
8. Towards atomic and close-to-atomic scale manufacturing10.1088/2631-7990/ab0dfc ↗
9. Evaluation of subsurface damage in GaN substrate induced by mechanical polishing with diamond abrasives10.1016/j.apsusc.2013.12.005 ↗
10. Phase transition and plastic deformation mechanisms induced by self-rotating grinding of GaN single crystals10.1016/j.ijmachtools.2021.103827 ↗
11. Molecular dynamics study on deformation behaviour of monocrystalline GaN during nano abrasive machining10.1016/j.apsusc.2020.145492 ↗
12. Study on subsurface damage mechanism of gallium nitride in nano-grinding10.1016/j.mssp.2021.105760 ↗
13. Growth of cubic phase gallium nitride by modified molecular‐beam epitaxy10.1116/1.575869 ↗
14. Epitaxial growth of cubic and hexagonal GaN on GaAs by gas‐source molecular‐beam epitaxy10.1063/1.106344 ↗
15. Chemical mechanical polishing of gallium nitride with colloidal silica10.1149/2.024112jes ↗
16. Atomically smooth gallium nitride surface prepared by chemical-mechanical polishing with S2O82−-Fe2+ based slurry10.1016/j.triboint.2016.09.037 ↗
17. Effect of polishing parameters on chemical mechanical planarization of C-plane (0001) gallium nitride surface using SiO2 and Al2O3 abrasives10.1149/2.0181407jss ↗
18. Photo-electrochemical etching of free-standing GaN wafer surfaces grown by hydride vapor phase epitaxy10.1016/j.electacta.2015.04.166 ↗
19. Structural, morphological, optical, and gas sensing characteristics of ultraviolet-assisted photoelectrochemical etching derived AlInGaN nano-spikes10.1016/j.jmrt.2019.03.011 ↗
20. Photoelectrochemical mechanical polishing method for n-type gallium nitride10.1016/j.cirp.2019.04.121 ↗
21. Molecular simulation of the plastic deformation and crack formation in single grit grinding of 4H-SiC single crystal10.1016/j.ijmecsci.2023.108147 ↗
22. Research on the effects of machining-induced subsurface damages on mono-crystalline silicon via molecular dynamics simulation10.1016/j.apsusc.2012.06.087 ↗
23. Brittle-ductile transition and nano-surface generation in diamond turning of single-crystal germanium10.1016/j.jmapro.2022.08.028 ↗
24. Deformation and machining mechanism of nanocrystalline NiCoCrFe high entropy alloys10.1016/j.jallcom.2022.166525 ↗
25. Molecular dynamics simulation of SiC removal mechanism in a fixed abrasive polishing process10.1016/j.ceramint.2019.04.180 ↗
26. Coupling of double grains enforces the grinding process in vibration-assisted scratch: insights from molecular dynamics10.1016/j.jmatprotec.2022.117551 ↗
27. Nanotribological simulations of multi-grit polishing and grinding10.1016/j.wear.2015.03.006 ↗
28. The deformation mechanism of gallium-faces and nitrogen-faces gallium nitride during nanogrinding10.1016/j.ijmecsci.2021.106888 ↗
29. Investigation on gallium nitride with N-vacancy defect nano-grinding by molecular dynamics10.1016/j.jmapro.2020.06.018 ↗
30. Material removal mechanism and deformation characteristics of GaN surface at the nanoscale10.1016/j.spmi.2022.107159 ↗
31. Indenter radius effect on mechanical response of a-(11–20), c-(0001), and m-(-1100) plane GaN single crystals in nanoindentation: a molecular dynamics study10.1016/j.mssp.2022.106648 ↗
32. Molecular dynamics simulation on B3-GaN thin films under nanoindentation10.3390/nano8100856 ↗
33. Computer simulation of local order in condensed phases of silicon10.1103/PhysRevB.31.5262 ↗
34. Dislocation mobility and Peierls stress of c-type screw dislocations in GaN from molecular dynamics10.1016/j.commatsci.2018.07.014 ↗
35. An empirical potential for the calculation of the atomic structure of extended defects in wurtzite GaN10.1016/S0927-0256(00)00056-2 ↗
36. Effect of indenter radius on mechanical properties of B3-GaN in nanoindentation based on molecular dynamics
37. Effect of abrasive size on nano abrasive machining for wurtzite GaN single crystal via molecular dynamics study10.1016/j.mssp.2020.105439 ↗
38. Effects of surface texturing on nanotribological properties and subsurface damage of monocrystalline GaN subjected to scratching investigated using molecular dynamics simulation10.1016/j.apsusc.2020.148277 ↗
39. Hardness and fracture toughness of bulk single crystal gallium nitride10.1063/1.117865 ↗
40. Fast parallel algorithms for short-range molecular dynamics10.1006/jcph.1995.1039 ↗
41. Visualization and analysis of atomistic simulation data with OVITO - the open visualization tool10.1088/0965-0393/18/1/015012 ↗
42. Automated identification and indexing of dislocations in crystal interfaces10.1088/0965-0393/20/8/085007 ↗
43. Characterization of diamond thin films: diamond phase identification, surface morphology, and defect structures10.1557/JMR.1989.0373 ↗
44. A simple expression for radial distribution functions of pure fluids and mixtures10.1063/1.470654 ↗
45. Isothermal molecular dynamics calculations for liquid salts10.1016/0009-2614(71)80281-6 ↗
46. Nanomachining characteristics of textured polycrystalline NiFeCo alloy using molecular dynamics10.1016/j.jmapro.2021.12.039 ↗
47. Research on material removal mechanism and radial cracks during scribing single crystal gallium nitride10.1016/j.ceramint.2021.02.074 ↗
48. Study on subsurface layer of nano-cutting single crystal tungsten in different crystal orientations10.1016/j.apsusc.2020.146608 ↗
49. A molecular dynamics investigation into the mechanisms of subsurface damage and material removal of monocrystalline copper subjected to nanoscale high speed grinding10.1016/j.apsusc.2014.02.178 ↗
50. Effects of initial temperature on the damage of GaN during nanogrinding10.1016/j.apsusc.2021.149771 ↗
51. Temperature effect on mechanical response of c-plane monocrystalline gallium nitride in nanoindentation: a molecular dynamics study10.1016/j.ceramint.2020.02.035 ↗
52. Mechanical removal of SiC by multi-abrasive particles in fixed abrasive polishing using molecular dynamics simulation10.1016/j.commatsci.2021.110311 ↗
53. Influence of grinding parameters on Inconel 625 surface grinding10.1016/j.jmapro.2020.04.002 ↗