journal article·2021-03

Study on nano silicon carbide water-based cutting fluid in polysilicon cutting

Chunyan Yao, Dongdong Chen, Kaixiang Xu, Zhongli Zheng, Qiangsheng Wang, Yunfeng Liu

Publisher page

Abstract

Abstract Diamond wire sawing technology is widely used in polysilicon cutting. The poor lubrication performance of the common water-based cutting fluid results in many cutting grooves and kerfs on wafer surface, which increases the difficulty of subsequent processing. In this paper, the application of nanoparticles water-based cutting fluid in polysilicon diamond wire sawing was proposed to further improve surface quality of wafers. A novel water-based cutting fluid was prepared with nano silicon carbide (N–SiC), polyethylene glycol (PEG2000) and sodium carboxymethylcellulose (CMC-Na). The dispersibility and friction performance of N–SiC cutting fluid were studied. And then the cutting performance of cutting fluid with different N–SiC content was investigated. Research results show that the dispersibility and friction performance of cutting fluid with 0.2 wt% N–SiC, 0.5 wt% CMC-Na and 6 wt% PEG2000 are the best. N–SiC particles can effectively reduce the width of edge breakage and the surface roughness of polysilicon wafers. The width of edge breakage and the surface roughness reach the lowest value when the N–SiC content in the cutting fluid is 0.2 wt%.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Surface Polishing Techniques · Diamond and Carbon-based Materials Research · Advanced machining processes and optimization

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (25)

Show source-provided references
1. Study of the effect of experimental conditions on polysilicon solar cells10.1016/j.ijhydene.2017.08.070 ↗
2. Study on the subsurface microcrack damage depth in electroplated diamond wire saw slicing SiC crystal10.1016/j.ceramint.2018.09.088 ↗
3. Development status of solar crystalline silicon wafer and its technical standards, Chin
4. Wire sawing technology: a state-of-the-art review10.1016/j.precisioneng.2015.08.008 ↗
5. Next-generation multi-crystalline silicon solar cells: diamond-wire sawing, nano-texture and high efficiency10.1016/j.solmat.2015.05.030 ↗
6. Diamond wire sawing of solar silicon wafers: a sustainable manufacturing alternative to loose abrasive slurry sawing10.1016/j.promfg.2018.02.156 ↗
7. A study on surface grinding of 300 mm silicon wafers10.1016/S0890-6955(01)00122-5 ↗
8. Basic Mechanisms and models of multi-wire sawing10.1002/adem.200400578 ↗
9. A simple approach to fabricate amorphous silicon pattern on single crystal silicon10.1016/j.triboint.2005.09.022 ↗
10. The chemo-mechanical effect of cutting fluid on material removal in diamond scribing of silicon10.1063/1.4991536 ↗
11. Research on influence of cutting fluid on slicing single-crystal silicon wafers quality using electroplated diamond wire saw
12. Assessment of water-based fluids with additives in grinding disc cutting process10.1016/j.jclepro.2018.12.066 ↗
13. A finite element analysis of temperature variation in silicon wafers during wire saw slicing10.1016/j.ijmachtools.2007.07.009 ↗
14. A basic study on the behavior of slurry action at multi-wire saw10.4028/www.scientific.net/KEM.238-239.89 ↗
15. Deep eutectic solvents (DES) based on sulfur as alternative lubricants for silicon surfaces10.1016/j.molliq.2019.111728 ↗
16. A study of the tribological behaviour of TiO2 nano-additive water-based lubricants10.1016/j.triboint.2017.01.013 ↗
17. Enhancing of the tribological characteristics of the lubricant oils using Ni-promoted MoS2 nanosheets as nano-additives10.1016/j.triboint.2017.10.001 ↗
18. Morphology modulation of SiC nano-additives for mechanical robust high thermoelectric performance Mg2Si1− xSnx/SiC nano-composites10.1016/j.scriptamat.2016.08.010 ↗
19. Highly porous nano-SiC with very low thermal conductivity and excellent high temperature behavior10.1016/j.jeurceramsoc.2017.09.037 ↗
20. Development of SiO2 nanolubrication system to be used in sliding bearings10.1007/s00170-013-5566-9 ↗
21. The aggregation and deposition of carbon nanotubes in aquatic environment
22. Highly concentrated aqueous suspension containing fine SiC particles10.1016/j.ceramint.2019.07.188 ↗
23. Ductile mode behavior of silicon during scribing by spherical abrasive particles10.1016/j.procir.2016.02.341 ↗
24. Studies of the ductile mode of cutting brittle materials (A review)10.3103/S1063457613050018 ↗
25. Research on cutting force of high speed milling TB6 in different cooling lubricating conditions