journal article·2022-11

Effect of radial grooves pads on copper chemical mechanical polishing

Chulwoo Bae, Shinil Oh, Juhwan Kim, Donggeon Kwak, Seungjun Oh, Taesung Kim

Publisher page

Abstract

In this study, the effect of radial grooves (RG) pads employed in the copper chemical mechanical polishing/planarization (CMP) process was investigated, to improve the copper CMP performance. To this end, four types of pads were selected according to the number of RGs; the numbers of RGs were 0, 8, 16, and 32. The amount of slurry inflow/outflow was calculated for the selected number of RGs over the same duration, and the change in the slurry inflow/outflow according to the rotational speed of the head/platen was determined using a numerical method. The simulation results thus obtained demonstrated the differences in the amount of slurry inflow/outflow according to the number of RGs and the rotational speed of head/platen. At 90 rpm, the new slurry mass fractions of the circular groove (CG) pad and the RG-32 pad were 0.52754 and 0.67606, respectively, and the new slurry mass fraction of the RG-32 pad increased by about 22% compared to the result of the CG pad. Subsequently, the CMP process was performed using four types of pads at different head/platen rotational speed, and Cu removal rates were compared. According to the CMP evaluation results, the Cu removal rates improved with an increase in the number of RGs. At 90 rpm, the Cu wafer removal rates of the CG pad and the RG-32 pad were 4051.3 Å/min and 5047.2 Å/min, respectively, and when the RG-32 pad was used, the Cu wafer removal rate was increased by about 24.6%. Furthermore, the roughness of the Cu wafers was improved by increasing the number of RGs. Therefore, supplying new slurry and releasing the old slurry can affect the performance Cu CMP process.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Surface Polishing Techniques · Advanced machining processes and optimization · Integrated Circuits and Semiconductor Failure Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (22)

Show source-provided references
1. Chemical‐mechanical polishing for fabricating patterned W metal features as chip interconnects10.1149/1.2085434 ↗
2. Application of chemical mechanical polishing to the fabrication of VLSI circuit interconnections10.1149/1.2085872 ↗
3. A variable-size shallow trench isolation (STL) technology with diffused sidewall doping for submicron CMOS
4. Advances in characterization of CMP consumables10.1557/mrs2002.247 ↗
5. Material removal mechanism in chemical mechanical polishing: theory and modeling10.1109/66.920723 ↗
6. Effects of abrasive size distribution in chemical mechanical planarization: modeling and verification10.1109/TSM.2003.815199 ↗
7. Investigating slurry transport beneath a wafer during chemical mechanical polishing processes10.1149/1.1393455 ↗
8. Effect of slurry injection position on slurry mixing, friction, removal rate, and temperature in copper CMP10.1149/1.2048207 ↗
9. Characterizing slurry flow during CMP using laser induced fluorescence
10. Effect of pad groove width on slurry mean residence time and slurry utilization efficiency in CMP10.1016/j.mee.2016.02.035 ↗
11. Design and evaluation of pad grooves for copper CMP
12. Generation of pad debris during oxide CMP process and its role in scratch formation10.1149/1.3551507 ↗
13. Green chemical mechanical polishing of sapphire wafers using a novel slurry10.1039/D0NR04705H ↗
14. Development of a novel chemical mechanical polishing slurry and its polishing mechanisms on a nickel alloy10.1016/j.apsusc.2019.144670 ↗
15. A novel slurry for chemical mechanical polishing of single crystal diamond10.1016/j.apsusc.2021.150431 ↗
16. A computational study on slurry flow between a wafer and CMP pad with grooves
17. A numerical study on slurry flow with CMP pad grooves10.1016/j.mee.2020.111437 ↗
18. Modeling and simulation for the distribution of slurry particles in chemical mechanical polishing10.1007/s00170-014-6132-9 ↗
19. Analysis of flow between a wafer and pad during CMP processes10.1007/s11664-998-0141-0 ↗
20. In situ investigation of slurry flow fields during CMP10.1149/1.3223562 ↗
21. The theory and design of plate glass polishing machines
22. Effects of the polishing variables on the wafer-pad interfacial fluid pressure in chemical mechanical polishing of 12-inch wafer10.1149/2.063203jes ↗