Ultrasonic-assisted hot pressing of Bi2Te3-based thermoelectric materials
Source abstract
Abstract
Abstract In this study, n-type Bi2Te3-based bulk materials were prepared using the ultrasonic-assisted hot pressing. The effects of ultrasonic vibration on the mechanical and thermoelectric properties of the prepared samples were investigated. Field-emission scanning electron microscope (FESEM) tests revealed that the ultrasonic vibration refined the grain size to the submicron level. The grain size became smaller as the ultrasonic vibration duration is extended. The results showed that the sample with an ultrasonic vibration duration of 20 min (namely, Ultra 20) has a hardness of 64 HV0.3 and a flexural strength of 22.4 MPa, which represents an 82.9% and 50.2% improvement, respectively, over the untreated hot-pressed sample (namely, Ultra 0). As the ultrasonic vibration duration increased, the absolute value of the Seebeck coefficient was found to increase, whereas the electrical conductivity and the thermal conductivity decreased. The maximum dimensionless figure of merit (ZTmax) was 0.78 at 480 K for the Ultra 20 sample, which was 10.9% and 16.4% higher than the Ultra 10 and Ultra 0 samples, respectively. The results proved that both the mechanical properties and the thermoelectric properties of the Bi2Te2.7Se0.3 bulk materials are improved by ultrasonic vibration.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Thermoelectric Materials and Devices · Thermal properties of materials · Thermodynamic and Structural Properties of Metals and Alloys
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (38)
Show source-provided references
1. Enhanced thermoelectric performance in n-type Bi2Te2.95Se0.05 bulks fabricated by high pressure sintering technique10.1016/j.materresbull.2014.09.057 ↗
2. Point defect engineering of high-performance Bismuth-Telluride-based thermoelectric materials10.1002/adfm.201400474 ↗
3. High thermoelectric performance of Bi-Te alloy: defect engineering strategy10.1016/j.cap.2016.03.028 ↗
4. Mechanical properties of bismuth telluride based alloys with embedded MoS2 nano-particles10.1016/j.matdes.2016.04.042 ↗
5. The effect of texture degree on the anisotropic thermoelectric properties of (Bi,Sb)2(Te,Se)3 based solid solutions10.1039/C6RA21897K ↗
6. High-temperature mechanical and thermoelectric properties of p-Type Bi0.5Sb1.5Te3 commercial zone melting ingots10.1007/s11664-013-2938-8 ↗
7. Thermoelectric properties of 25% Bi2Te3-75% Sb2Te3 solid solution prepared by hot-pressing method10.1016/S0022-3697(96)00049-2 ↗
8. Thermoelectric and mechanical properties of the Bi0.5Sb1.5Te3 solid solution prepared by melt spinning10.1134/S0020168513020106 ↗
9. Spark plasma sintered bismuth telluride-based thermoelectric materials incorporating dispersed boron carbide10.1016/j.jallcom.2014.12.010 ↗
10. Preferential scattering by interfacial charged defects for enhanced thermoelectric performance in few-layered n-type Bi2Te310.1038/srep03212 ↗
11. Experimental investigation of ultrasonic assisted equal channel angular pressing process10.1016/j.acme.2015.10.001 ↗
12. Microstructure of the pure copper produced by upsetting with ultrasonic vibration10.1016/j.matlet.2011.08.086 ↗
13. Hypereutectic Al-Si based alloys with a thixotropic microstructure produced by ultrasonic treatment10.1016/S0261-3069(97)00072-1 ↗
14. Tuning multiscale microstructures to enhance thermoelectric performance of n-type Bismuth-Telluride-based solid solutions10.1002/aenm.201500411 ↗
15. Ordered structure and high thermoelectric properties of Bi2(Te,Se)3 nanowire array10.1016/j.nanoen.2013.07.009 ↗
16. A novel chemical process of Bi2Te2.7Se0.3 nanocompound for effective adjustment in transport properties resulting in remarkable n-type thermoelectric performance10.1016/j.scriptamat.2016.03.010 ↗
17. Electronic transport in semimetallic cerium sulfide10.1103/PhysRev.133.A1143 ↗
18. Microstructure and mechanical properties of AZ61 alloys with large cross-sectional size fabricated by multi-pass ECAP10.1016/j.msea.2012.09.092 ↗
19. Mechanically enhanced p-and n-type Bi2Te3-based thermoelectric materials reprocessed from commercial ingots by ball milling and spark plasma sintering10.1016/j.mseb.2015.03.011 ↗
20. Enhanced grain refinement and microhardness of Ti-Al-V alloy by electropulsing ultrasonic shock10.1016/j.jallcom.2014.09.192 ↗
21. Modified constitutive equation for use in modeling the ultrasonic vibration enhanced friction stir welding process10.1016/j.scriptamat.2016.03.023 ↗
22. Effects of superimposed ultrasonic vibration on compressive deformation of metals10.2320/matertrans1960.7.162 ↗
23. Microstructure of the pure copper produced by upsetting with ultrasonic vibration10.1016/j.matlet.2011.08.086 ↗
24. A comparative study of mechanical and microstructural characteristics of aluminium and titanium undergoing ultrasonic assisted compression testing10.1016/j.msea.2016.11.021 ↗
25. Microstructural evolution and nanocrystal formation during deformation of Fe-C alloys10.1016/j.msea.2003.10.136 ↗
26. Acoustic softening and residual hardening in aluminum: modeling and experiments10.1016/j.ijplas.2012.06.003 ↗
27. Effects of superimposed high-frequency vibration on deformation of aluminum in micro/meso-scale upsetting10.1016/j.jmatprotec.2011.10.017 ↗
28. Mechanical metallization of alumina substrate through shot impact treatment10.1016/j.jeurceramsoc.2013.08.022 ↗
29. A study on non-isothermal static recrystallization during hot rolling of carbon steels10.1080/10426914.2012.675535 ↗
30. Dynamic recrystallization behavior of Ti–5Al–5Mo–5V–1Cr–1Fe alloy10.1016/j.matdes.2014.06.064 ↗
31. Microstructural evolution of a nickel-based superalloy during hot deformation10.1016/j.matdes.2015.04.004 ↗
32. Thermoelectric property studies on Cu-doped n-type CuxBi2Te2.7Se0.3 nanocomposites10.1002/aenm.201100149 ↗
33. Effect of ball milling and post treatment on crystal defects and transport properties of Bi2(Se,Te)3 compounds10.1063/1.3658256 ↗
34. Effects of Cu incorporation as an acceptor on the thermoelectric transport properties of CuxBi2Te2.7Se0.3 compounds10.1016/j.jallcom.2016.11.257 ↗
35. Combined effect of nanoscale grain size and porosity on lattice thermal conductivity of bismuth-telluride-based bulk alloys10.1063/1.4759326 ↗
36. Dames · 2006 · 421
37. Enhanced thermoelectric performance of nanostructured Bi2Te3 through significant phonon scattering10.1021/acsami.5b07596 ↗
38. Experimental studies on anisotropic thermoelectric properties and structures of n-type Bi2Te2.7Se0.310.1021/nl101156v ↗