Molecular dynamics simulation of AFM tip-based hot scratching of nanocrystalline GaAs
Source abstract
Abstract
GaAs is a hard, brittle material and its cutting at room-temperature is rather difficult, so the work explored whether hot conditions improve its cutting performance or not. Atomic force microscope (AFM) tip-based hot machining of the (0 1 0) oriented single crystal GaAs was simulated using molecular dynamics (MD). Three representative temperatures 600 K, 900 K and 1200 K (below the melting temperature of ~1511 K) were used to cut GaAs to benchmark against the cutting performance at 300 K using indicators such as the cutting forces, kinetic coefficient of friction, cutting temperature, shear plane angle, sub-surface damage depth, shear strain in the cutting zone, and stress on the diamond tip. Hotter conditions resulted in the reduction of cutting forces by 25% however, the kinetic coefficient of friction went up by about 8%. While material removal rate was found to increase with the increase of the substrate temperature, it was accompanied by an increase of the sub-surface damage in the substrate. Simulations at 300 K showed four major types of dislocations with Burgers vector 1/2<110>, 1/6<112>, <0-11> and 1/2<1-12> underneath the cutting zone and these were found to cause ductile response in zinc-blende GaAs. Lastly, a phenomenon of chip densification was found to occur during hot cutting which referred to the fact that the amorphous cutting chips obtained from cutting at low temperature will have lower density than the chips obtained from cutting at higher temperatures.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Force Microscopy Techniques and Applications · Advanced Surface Polishing Techniques · Diamond and Carbon-based Materials Research
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (44)
Show source-provided references
1. 28 GHz GaAs pHEMT MMICs and RF front-end module for 5G communication systems10.1002/mop.31669 ↗
2. The interface states and series resistance analyzing of Au/SiO 2/n-GaAs at high temperatures10.1016/j.jallcom.2013.04.098 ↗
3. Stopping power of GaAs for swift protons: dielectric function and optical-data model calculations10.1016/j.nimb.2010.02.047 ↗
4. High efficiency and radiation resistant InGaP/GaAs//CIGS stacked solar cells for space applications
5. An enzymatic biosensor based on three-dimensional ZnO nanotetrapods spatial net modified AlGaAs/GaAs high electron mobility transistors10.1063/1.4902944 ↗
6. High magnetic field spin splitting of excitons in asymmetric GaAs quantum wells10.1103/PhysRevB.86.245401 ↗
7. Photoluminescence of GaAs nanowires at an energy larger than the zincblende band-gap: dependence on growth parameters10.1088/0268-1242/30/5/055020 ↗
8. Hardness and fracture toughness of semiconducting materials studied by indentation and erosion techniques10.1016/0025-5416(88)90489-2 ↗
9. Critique of materials-based models of ductile machining in brittle solids10.1111/jace.17344 ↗
10. Elastic recovery of monocrystalline silicon during ultra-fine rotational grinding10.1016/j.precisioneng.2020.05.004 ↗
11. Chavoshi · 2016
12. An atomistic investigation on the wear of diamond during atomic force microscope tip-based nanomachining of gallium arsenide10.1016/j.commatsci.2020.110115 ↗
13. A theoretical assessment of surface defect machining and hot machining of nanocrystalline silicon carbide10.1115/1.4026297 ↗
14. Horizons of modern molecular dynamics simulation in digitalized solid freeform fabrication with advanced materials10.1016/j.mtchem.2020.100356 ↗
15. Molecular dynamics simulation study of deformation mechanisms in 3C-SiC during nanometric cutting at elevated temperatures10.1016/j.msea.2015.11.100 ↗
16. Atomic-scale characterization of occurring phenomena during hot nanometric cutting of single crystal 3C-SiC10.1039/C6RA05830B ↗
17. Molecular dynamics simulation investigation on the plastic flow behaviour of silicon during nanometric cutting10.1088/0965-0393/24/1/015002 ↗
18. An atomistic simulation investigation on chip related phenomena in nanometric cutting of single crystal silicon at elevated temperatures10.1016/j.commatsci.2015.11.027 ↗
19. Influence of temperature on the anisotropic cutting behaviour of single crystal silicon: a molecular dynamics simulation investigation10.1016/j.jmapro.2016.06.009 ↗
20. Dislocation-mediated plasticity in silicon during nanometric cutting: a molecular dynamics simulation study10.1016/j.mssp.2016.05.003 ↗
21. Direct nanometer-scale patterning by the cantilever oscillation of an atomic force microscope10.1063/1.124351 ↗
22. Controlled mechanical AFM machining of two-dimensional electron systems: fabrication of a single-electron transistor10.1016/S1386-9477(99)00230-1 ↗
23. Nanoscale devices fabricated by direct machining of GaAs with an atomic force microscope10.1016/S0304-3991(99)00127-8 ↗
24. Fundamental study of diamond turning of single crystal gallium arsenide10.1016/j.precisioneng.2019.11.010 ↗
25. Fast parallel algorithms for short range molecular dynamics10.1006/jcph.1995.1039 ↗
26. A unified formulation of the constant temperature molecular-dynamics methods10.1063/1.447334 ↗
27. VMD - visual molecular dynamics10.1016/0263-7855(96)00018-5 ↗
28. Visualization and analysis of atomistic simulation data with OVITO-the Open Visualization Tool10.1088/0965-0393/18/1/015012 ↗
29. Analytic bond-order potential for the gallium arsenide system10.1103/PhysRevB.73.045206 ↗
30. Analytical bond-order potential for the cadmium telluride binary system10.1103/PhysRevB.85.115206 ↗
31. SRIM - the stopping and range of ions in matter (2010)10.1016/j.nimb.2010.02.091 ↗
32. Influence of microstructure on the cutting behaviour of silicon10.1016/j.actamat.2015.11.046 ↗
33. Peak effect versus skating in high temperature nanofriction10.1038/nmat1836 ↗
34. Nanotribology at high temperatures10.3762/bjnano.3.68 ↗
35. Effect of heat treatment on the properties of nano-diamond under oxygen and argon ambient10.1016/S0925-9635(01)00680-X ↗
36. Dieter · 1986
37. Mechanical behavior of undoped n-type GaAs under the indentation of berkovich and flat-tip indenters10.3390/ma12071192 ↗
38. Nanoindentation and nanoscratch characteristics of Si and GaAs10.1016/j.mee.2005.01.025 ↗
39. Automated identification and indexing of dislocations in crystal interfaces10.1088/0965-0393/20/8/085007 ↗
40. Ganchenkova · 2015
41. Theory of shear banding in metallic glasses and molecular dynamics calculations10.2320/matertrans.MJ200769 ↗
42. Dynamics of viscoplastic deformation in amorphous solids10.1103/PhysRevE.57.7192 ↗
43. Atomistic investigation on the structure-property relationship during thermal spray nanoparticle impact10.1016/j.commatsci.2013.12.011 ↗
44. Goel · 2013