journal article·2021-08

Finite element analysis on processing stress of polysilicon cut by diamond multi-wire saw

Dameng Cheng, Yufei Gao, Runtao Liu

Publisher page

Abstract

Abstract At present, diamond multi-wire sawing technology has been applied to the slicing of polysilicon wafers. The residual microcracks on the surface and subsurface of the silicon wafer due to material brittle removal are prone to expand and interfere under the sawing stress, which reduces the fracture strength of the silicon wafer and leads to breakage. However, the dynamic change and distribution of sawing stress is still difficult to measure by experiment. In this paper, the two ways of ductile and brittle material removal of abrasives at different azimuth angles on the saw wire surface were considered, the sawing force model of diamond wire sawing was established. Then based on the sawing force model, a finite element model of multi-wire sawing polysilicon was established. The distribution and coupling characteristics of sawing stress and the influence of process parameters and silicon wafer size characteristics on the stress value and distribution were studied. The research results show that the mechanical stress value during the sawing process is relatively small and accounts for a small proportion of the coupling stress, but it will affect the distribution of the coupling stress, and the thermal stress is dominant. The coupling stress increases with the increase of saw wire speed and feed speed. When the ratio of saw wire speed to feed speed is constant, the larger the value of saw wire speed and feed speed is, the larger the coupling stress is. The increase in the size and thickness of the silicon wafer will increase the coupling stress, while the change in the thickness of the silicon wafer has little effect on the value of the coupling stress. The research results of the paper provide a theoretical reference for understanding the changes and distribution of sawing stress, optimizing process parameters and improving the quality of sawing.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Surface Polishing Techniques · Tunneling and Rock Mechanics · Diamond and Carbon-based Materials Research

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (42)

Show source-provided references
1. Silicon solar cells: toward the efficiency limits
2. Effect of growth rate and wafering on residual stress of diamond wire sawn silicon wafers
3. General trends about photovoltaics based on crystalline silicon10.1016/S0927-0248(01)00145-3 ↗
4. Diamond wire sawing of solar silicon wafers: a sustainable manufacturing alternative to loose abrasive slurry sawing
5. Research on the machinability of A-plane sapphire under diamond wire sawing in different sawing directions10.1016/j.ceramint.2019.02.086 ↗
6. H. Li, Y. Gao, P. Ge, W. Bi, L. Zhang, Study on process parameters of fabrication fine diameter electroplated diamond wire for slicing crystalline silicon solar cell, Int. J. Adv. Manuf. Technol. 106 (7–8) (2 020) 3153-3175.10.1007/s00170-019-04860-2 ↗
7. Mechanisms of material removal and subsurface damage in fixed-abrasive diamond wire slicing of single-crystalline silicon10.1016/j.precisioneng.2017.04.011 ↗
8. Nucleation location and propagation direction of radial and median cracks for brittle material in scratching10.1016/j.ceramint.2019.01.046 ↗
9. Analytical prediction of subsurface microcrack damage depth in diamond wire sawing silicon crystal10.1016/j.mssp.2020.105015 ↗
10. The impact of subsurface damage on the fracture strength of diamond-wire-sawn monocrystalline silicon wafers
11. Study on mechanism of crack propagation of sapphire single crystals of four different orientations under impact load and static load10.1016/j.ceramint.2019.01.021 ↗
12. Experimental study on slicing photovoltaic polycrystalline silicon with diamond wire saw10.1016/j.mssp.2019.104779 ↗
13. Roughness damage evolution due to wire saw process10.1007/s12541-011-0126-4 ↗
14. Mechanisms of material removal and subsurface damage in fixed-abrasive diamond wire slicing of single-crystalline silicon10.1016/j.precisioneng.2017.04.011 ↗
15. Surface characteristics and damage distributions of diamond wire sawn wafers for silicon solar cells10.3934/matersci.2016.2.669 ↗
16. Analytical force modeling of fixed abrasive diamond wire saw machining with application to sic monocrystal wafer processing10.1115/1.4034792 ↗
17. Force modeling of silicon monocrystal wire saw machining
18. Experimental research on monocrystalline Si high-speed wire sawing force based on RSM
19. Prediction of sawing force for single-crystal silicon carbide with fixed abrasive diamond wire saw10.1016/j.mssp.2017.01.014 ↗
20. Depth of cut for single abrasive and cutting force in resin bonded diamond wire sawing10.1007/s00170-016-8896-6 ↗
21. Experiment and theoretical prediction for surface roughness of PV polycrystalline silicon wafer in electroplated diamond wire sawing
22. Finite element investigation on the evolution of wear and stresses in brazed CBN grits during grinding10.1007/s00170-015-7262-4 ↗
23. Finite element simulation study on pre-stress multi-step cutting of Ti-6Al-4V titanium alloy10.1007/s00170-019-04122-1 ↗
24. Meso-scale tool breakage prediction based on finite element stress analysis for shoulder milling of hardened steel10.1016/j.jmapro.2020.03.044 ↗
25. Finite element analysis of tool stresses, temperature and prediction of cutting forces in turning process10.4028/www.scientific.net/SSP.261.354 ↗
26. Coupling stress caused by thermal and slicing force in KDP crystal slicing with fixed abrasive wire saw10.1007/s00170-018-1893-1 ↗
27. A finite element analysis of sawing stress in fixed-abrasive wire saw slicing KDP crystal10.1007/s00170-016-9916-2 ↗
28. Study on the subsurface microcrack damage depth in electroplated diamond wire saw slicing SiC crystal10.1016/j.ceramint.2018.09.088 ↗
29. Finite element analysis of multi-wire saw silicon rods with consolidated abrasive diamonds10.1007/s00170-016-9321-x ↗
30. A finite element analysis of temperature variation in silicon wafers during wiresaw slicing10.1016/j.ijmachtools.2007.07.009 ↗
31. Heat transfer during multiwire sawing of silicon wafers10.1115/1.4006591 ↗
32. Three-dimensional shape modeling of diamond abrasive grains measured by a scanning laser microscope10.4028/www.scientific.net/KEM.238-239.131 ↗
33. Durability studies of micro/nanoelectromechanical systems materials, coatings and lubricants at high sliding velocities (up to 10 mm/s) using a modified atomic force microscope10.1116/1.1843821 ↗
34. The response of solids to elastic/plastic indentation. I. Stresses and residual stresses10.1063/1.329930 ↗
35. Elastic-plastic indentation damage in ceramics-the median-radial crack system10.1111/j.1151-2916.1980.tb10768.x ↗
36. A new method of determining the slicing parameters for fixed diamond10.1016/j.mssp.2020.105252 ↗
37. Prediction of warping in silicon wafer slicing with wire-saw machine
38. Temperature distributions and thermal deformations of mirror substrates in laser resonators10.1364/AO.40.004824 ↗
39. Jiao · 2014
40. Theoretical research on temperature in diamond wire sawing
41. Experimental investigation of temperatures in diamond wire sawing granite10.4028/www.scientific.net/KEM.404.185 ↗
42. Material removal and surface generation mechanisms in diamond wire sawing of silicon crystal10.1016/j.mssp.2019.104642 ↗