journal article·2018-08

Material removal of single crystal 4H-SiC wafers in hybrid laser-waterjet micromachining process

Shaochuan Feng, Chuanzhen Huang, Jun Wang, Hongtao Zhu

Publisher page

Abstract

Abstract Yield stress, as well as ultimate stress, decreases with an increased temperature. A much smaller cutting force can be applied to perform the machining at high temperatures. Material is considered “softened” when its yield and ultimate stresses decrease due to the increase of temperature. During the hybrid laser-waterjet micromachining process, the material is heated by laser. Once the critical resolved shear stress (CRSS), related to the yield stress, decreases to be equal to the applied resolved shear stress induced by the pressurized waterjet impingement, the material begins to be deformed and then removed plastically. The hybrid laser-waterjet micromachining technology shows a satisfying performance on almost damage-free and high-efficient micromachining of thermal-sensitive and hard-brittle materials at their “softened” status. The present study is focused on the material removal mechanism of single crystal 4H-SiC in the hybrid laser-waterjet micromachining process. The temperature-dependent CRSS on the primary slip system of 4H-SiC is formulated. It is shown that the CRSS of 4H-SiC is less than 5 MPa at 1650 K. The shear stress induced by pressurized waterjet impingement, laser heating effect under the laser-water interference and the waterjet cooling effect are respectively studied. The range of water pressure used in the machining process is from 4 MPa to 13 MPa. A 2-D numerical model is developed using the finite difference method (FDM). The simulations show that the material begins to be removed before the laser intensity reaches its maximum in a laser pulse cycle. The depth and width of the microgroove increase gradually in the following several cycles. The increments become gradually less until this increase stops. The material is removed before it’s heated to its melting temperature and at a softened but still solid status. Heat accumulation between laser pulses is not expected in the process. The machined surface quality and material removal mechanisms of the hybrid laser-waterjet micromachining and laser dry ablation are compared by 3D profiles and SEM photographs of the microgrooves obtained from these two machining methods. The surface quality obtained from hybrid laser-waterjet micromachining is better than that obtained from laser dry ablation. The protrusion strips along the cut edges of laser dry ablation are scaly and similar to welded junction. It indicates that the material is melted or vaporized by laser heating and re-solidified at cut edges to form a recast layer during laser dry ablation. There aren’t recast layers on the machined surface of hybrid laser-waterjet micromachining. Its surface texture is characterized as a typical feature of plastic slip.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Laser Material Processing Techniques · Diamond and Carbon-based Materials Research · Advanced Surface Polishing Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (30)

Show source-provided references
1. Laser micro machining of 3C-SiC single crystals10.1016/j.mee.2006.01.064 ↗
2. Waterjet-guided laser processing10.1117/12.486514 ↗
3. Laser ablation of titanium alloy under a thin and flowing water layer10.1016/j.ijmachtools.2014.10.013 ↗
4. Laser ablation at solid–liquid interfaces: an approach from optical emission spectra10.1063/1.481465 ↗
5. Fracture mechanics-based analysis for hybrid laser/waterjet (LWJ) machining of yttria-partially stabilized zirconia (Y-PSZ)10.1016/j.ijmachtools.2009.09.002 ↗
6. Transition from brittleness to ductility in SiC10.1088/0953-8984/14/48/335 ↗
7. S.R. Virkar, J.A. Patten, Numerical simulations and analysis of the thermal effects on silicon carbide during ductile mode micro-laser assisted machining, in: Proceedings ASME 2009 International Manuf. Sci. Eng. Conference, West Lafayette, pp. 409–416, 2009, 〈http://dx.doi.org/10.1115/MSEC.2009-84046〉.10.1115/MSEC2009-84046 ↗
8. J.A. Patten, M.K. Ghantasala, D. Ravindra, H.B. Poyraz, S. Virkar, The effects of laser heating on the material removal process in Si and SiC nanomachining, in: Proceedings 2011 NSF Eng. Res. Innov. Conference, Atlanta, 2011.
9. An investigation of hybrid laser – waterjet ablation of silicon substrates10.1016/j.ijmachtools.2012.01.002 ↗
10. Investigation and modelling of hybrid laser-waterjet micromachining of single crystal SiC wafers using response surface methodology10.1016/j.mssp.2017.05.029 ↗
11. An experimental investigation on laser assisted waterjet micro-milling of silicon nitride ceramics
12. The relationship between activation parameters and dislocation glide in 4H-SiC single crystals10.1002/1521-3951(200011)222:1<75::AID-PSSB75>3.0.CO;2-0 ↗
13. In: P. Villars, K. Cenzual (eds.), 4H-SiC (SiC 4H) Crystal Structure: Datasheet from “PAULING FILE Multinaries Edition – 2012” in SpringerMaterials, (n.d.), 〈http://materials.springer.com/isp/crystallographic/docs/sd_1628877〉.
14. Plastic behavior of 4H-SiC single crystals deformed at low strain rates10.1016/S1359-6462(00)00495-4 ↗
15. Plasticity and deformation microstructure of 4H-SiC below the brittle-to-ductile transition
16. Impinging circular turbulent jets10.1061/JYCEAJ.0004072 ↗
17. Plane turbulent impinging jets10.1080/00221687309499789 ↗
18. Oblique impingement of circular turbulent jets10.1080/00221687609499685 ↗
19. Oblique impingement of plane turbulent jets10.1061/JYCEAJ.0004605 ↗
20. Hirth · 1968
21. On temperature dependence of deformation mechanism and the brittle–ductile transition in semiconductors10.1557/JMR.1999.0372 ↗
22. Effect of test temperature and strain rate on the yield stress of monocrystalline 6H-SiC10.1002/(SICI)1521-396X(199803)166:1<155::AID-PSSA155>3.0.CO;2-V ↗
23. Mathematical modeling and experimental verification of stationary waterjet cleaning process10.1115/1.2830161 ↗
24. An analytical model for the prediction of temperature distribution and evolution in hybrid laser-waterjet micro-machining10.1016/j.precisioneng.2016.07.002 ↗
25. Meschede · 2007
26. Local heat transfer to impinging liquid jets in the initially laminar, transitional, and turbulent regimes10.1016/0017-9310(94)90206-2 ↗
27. Duffy · 2003
28. Thermal conductivity of 4H-SiC single crystals10.1063/1.4790134 ↗
29. Experimental and theoretical analysis of the high temperature thermal conductivity of monocrystalline SiC10.4028/www.scientific.net/MSF.264-268.623 ↗
30. A study of near-infrared nanosecond laser ablation of silicon carbide10.1016/j.ijheatmasstransfer.2013.06.050 ↗