Multi-objective optimization for silicon wafer slicing using wire-EDM process
Source abstract
Abstract
Abstract The existing silicon ingot slicing methods adopt contact forces in slicing that could easily cause higher kerf loss and a larger variation in the thickness of the sliced wafers. Wire-EDM is a potential process for slicing of silicon ingots into wafers. This work therefore demonstrates capability of wire-EDM in silicon wafer slicing through a RSM based experimentation involving use of molybdenum wires of 40–120 μm in diameter. During the experiments wafers of various height ranging from 50 to 150 mm were fabricated and capability of the process was assessed in minimizing the kerf width. It was evident that the kerf width reduces from 250 μm to 50 μm, when sliced by a 40 μm diameter wire, which amounts to a reduction in kerf loss by 300%. The slicing speed on the other hand could be increased by 40–50% to 2.5 mm/min over the conventional abrasive slicing. A multi-objective optimization methodology adopted gives parametric conditions that give minimum kerf width at the highest slicing speed and the lowest surface roughness.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Surface Polishing Techniques · Advanced Machining and Optimization Techniques · Advanced machining processes and optimization
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (19)
Show source-provided references
1. P.D. Maycock, PV News, February 2000, March 2001, April 2002-10-14.
2. G.P. Willeke, The Fraunhofer ISE Roadmap for Crystalline Silicon Solar Cell Technology, in: Proceedings of the 29th IEEE Photovoltaic Specialists Conference, New Orleans, Louisiana, USA, May 20–24, 2002.10.1109/PVSC.2002.1190454 ↗
3. Optimization of fabrication process of high-efficiency and low-cost crystalline silicon solar cell for industrial applications10.1016/j.solmat.2008.10.013 ↗
4. Investigation of silicon wafering by wire EDM10.1007/BF01119742 ↗
5. Study of electrical discharge machining technology for slicing silicon ingots10.1016/S0924-0136(03)00718-0 ↗
6. B. Yu, H. Lee, Y. Lin, S. Qin, F. Huang, B. Yan, Study of wire electrical discharge machining for poly-silicon, Asian Symposium for Precision Engineering and Nanotechnology, 2009.
7. High efficiency slicing of low resistance silicon ingot by wire electrolytic–spark hybrid machining10.1016/j.jmatprotec.2008.07.029 ↗
8. Dongre · 2010
9. Improvement of wire electrical discharge machining efficiency in machining polycrystalline silicon with auxiliary-pulse voltage supply10.1007/s00170-011-3350-2 ↗
10. Response surface analysis of slicing of silicon ingots with focus on photovoltaic application10.1080/10910344.2012.731952 ↗
11. Modeling and analysis of the wire-tool vibration in wire-cut EDM10.1016/S0924-0136(03)00280-2 ↗
12. Evaluations of spark distribution and wire vibration in wire EDM by high-speed observation10.1016/j.cirp.2010.03.073 ↗
13. A. Desai, G.G. Dongre, S.S. Joshi, Modelling of wire vibrations in wire electrical discharge machining, in: Proceedings of the 8th International Conference on Precision, Meso, Micro and Nano Engineering (COPEN), National Institute of Technology Calicut, Kerala, India, December 13–15, 2013.
14. Corner error simulation of rough cutting in wire EDM10.1016/j.precisioneng.2007.01.005 ↗
15. A simplified post process for wire cut EDM10.1016/0924-0136(95)02212-0 ↗
16. B.H. Yu, H.K. Lee, Y.X. Lin, S.J. Qin, F.Y. Huang, B.H. Yan, Study of Wire Electrical Discharge Machining for Poly-silicon, in: Asian Symposium for Precision Engineering and Nanotechnology, 2009.
17. Slicing, cleaning and kerf analysis of germanium wafers, machined by wire electrical discharge machining10.1016/j.jmatprotec.2008.08.027 ↗
18. Simultaneous optimization of several response variables10.1080/00224065.1980.11980968 ↗
19. Multi-response optimization of EDM with Al–Cu–Si–TiC P/M composite electrode10.1007/s00170-008-1825-6 ↗