Dopant, composition and carrier profiling for 3D structures
Source abstract
Abstract
Abstract With the transition from planar to three-dimensional device architectures, devices such as FinFETs, TFETs and nanowires etc. become omnipresent. This requires the dopant atom positioning relative to the gate edges and contacts with controlled 3D distribution, adequate conformality, appropriate concentrations and activation, all of which are important challenges which need to be resolved since they determine the device performance. Developing an appropriate doping technology for the next technology generation requires a concurrent effort in establishing adequate metrology such that appropriate feedback on process steps and the underlying physics can be generated in a timely manner and with sufficient resolution and accuracy. When assessing performance of such metrology tools and concepts for 3D devices and structures, one needs to address not only the ability to achieve 3D spatial resolution, but also the physical property which is probed, i.e. dopants versus carriers, as well as the complexity of the method used because this impacts on success rate, turn-around time, throughput, automation etc. An evaluation in terms of time to data is as important as the technical capabilities. Although techniques with inherently good 3D resolution (e.g. atom probe tomography) might appear to offer the ideal solution for these applications, routine application is still hampered by localization problems during sample preparation, reconstruction artefacts due to inhomogeneous evaporation and differential laser light absorption, limited sensitivity due to the reduced counting statistics, poor tip yield, small throughput, etc. Hence, complementary analysis using 1D methods like secondary ion mass spectrometry (SIMS) are being explored to provide dopant or composition analysis in 3D structures given its high degree of reproducibility, ease of application and industrial acceptance. Targeting carrier profiling in 3D structures and confined volumes as a complement to atom probe (or SIMS) dopant profiles, has led to the extension of scanning probe microscopy (SPM) methods (which are inherently 2D) toward 3D metrology by exploiting either dedicated test structures or through novel approaches such as Scalpel SPM. The application of these SPM methods for 3D structures and confined volumes has demonstrated that the changing surface/volume ratio in confined devices leads to various phenomena (e.g. dopant deactivation, enhanced diffusion,..) which are not observed in blanket sample experiments. More emphasis should therefore be placed on the analysis of devices and structures with the relevant dimensions relative to the exploration of blanket experiments. Thus, the metrology concepts addressed in this paper may be very useful for such investigations.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Materials Characterization Techniques · Force Microscopy Techniques and Applications · Electronic and Structural Properties of Oxides
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (94)
Show source-provided references
1. D. Hisamoto, J. Kedzierski, E. Anderson, H. Takeuchi, K. Asano, J. Bokor, A folded-channel MOSFET for deep-sub-tenth micron era, in: Proceedings of the International Electron Devices Meet. 1998. Tech. Dig. (Cat. No.98CH36217), IEEE, 1998, pp. 1032–1034. doi:10.1109/IEDM.1998.746531.10.1109/IEDM.1998.746531 ↗
2. Low-voltage tunnel transistors for beyond cmos logic10.1109/JPROC.2010.2070470 ↗
3. Intel 22nm 3-D Tri-Gate Transistor Technology | Intel Newsroom. 〈http://newsroom.intel.com/docs/DOC-2032#pressmaterials〉, 2011 (accessed 08.09.16).
4. Complementary silicon-based heterostructure tunnel-FETs with high tunnel rates10.1109/LED.2008.2007599 ↗
5. W. Vandervorst, J.L. Everaert, E. Rosseel, M. Jurczak, T. Hoffman, P. Eyben, J. Mody, G. Zschätzsch, S. Koelling, M. Gilbert, T. Poon, J. del Agua Borniquel, M. Foad, R. Duffy, B.J. Pawlak, E.G. Seebauer, S.B. Felch, A. Jain, Y. V. Kondratenko, Conformal doping of FINFETs: a Fabrication and Metrology Challenge, in: AIP Conference Proceedings, AIP, 2008: pp. 449–456. doi:10.1063/1.3033660.10.1063/1.3033660 ↗
6. Observation of diameter dependent carrier distribution in nanowire-based transistors10.1088/0957-4484/22/18/185701 ↗
7. Diameter-dependent boron diffusion in silicon nanowire-based transistors10.1063/1.4790438 ↗
8. 2011 ITRS - International Technology Roadmap for Semiconductors, Metrology Report, 2011. 〈http://www.itrs2.net/2011-itrs.html〉.
9. Toward atom probe tomography of microelectronic devices10.1088/1742-6596/326/1/012030 ↗
10. Experimental studies of dose retention and activation in fin field-effect-transistor-based structures10.1116/1.3269755 ↗
11. Wilson · 1989
12. van der Heide · 2014
13. Stevie · 2015
14. Dopant/carrier profiling for 3d-structures10.1002/pssc.201300329 ↗
15. SIMS Analysis on the transistor scale: probing composition and dopants in non-planar, confined 3d-volumes
16. Self Focusing SIMS: probing thin film composition in very confined volumes10.1016/j.apsusc.2016.01.056 ↗
17. A.K. Kambham, G. Zschaetzsch, Y. Sasaki, M. Togo, N. Horiguchi, J. Mody, A. Florakis, D.R. Gajula, A. Kumar, M. Gilbert, W. Vandervorst, Atom Probe Tomography for 3D-dopant analysis in FinFET devices, in: Proceedings of the 2012 Symposium on VLSI Technology, IEEE, 2012, pp. 77–78. doi:10.1109/VLSIT.2012.6242469.10.1109/VLSIT.2012.6242469 ↗
18. Probing doping conformality in fin shaped field effect transistor structures using resistors10.1116/1.2789439 ↗
19. Composition analysis of III–V materials grown in nanostructures: the self-focusing-SIMS approach
20. Investigation of the formation of M2+-molecular ions in sputtering processes10.1016/S1044-0305(98)00143-3 ↗
21. Gault · 2012
22. Larson · 2013
23. Miller · 2014
24. Advances in atom probe tomography instrumentation: implications for materials research10.1557/mrs.2015.311 ↗
25. Atom probe tomography—A cornerstone in materials characterization10.1557/mrs.2015.313 ↗
26. Atom probe tomography of nanoscale electronic materials10.1557/mrs.2015.308 ↗
27. Atom-probe tomography of semiconductor materials and device structures10.1557/mrs2009.248 ↗
28. Atom probe tomography of electronic materials10.1146/annurev.matsci.37.052506.084239 ↗
29. Advanced volume reconstruction and data mining methods in atom probe tomography10.1557/mrs.2015.312 ↗
30. In situ site-specific specimen preparation for atom probe tomography10.1016/j.ultramic.2006.06.008 ↗
31. Atom-probe for FinFET dopant characterization10.1016/j.ultramic.2011.01.017 ↗
32. A reproducible method for damage-free site-specific preparation of atom probe tips from interfaces10.1002/jemt.21081 ↗
33. Review of atom probe FIB-based specimen preparation methods10.1017/S1431927607070845 ↗
34. Atom Probe Tomography 201210.1146/annurev-matsci-070511-155007 ↗
35. Atom probe tomography of SRAM transistors: specimen preparation methods and analysis10.1016/j.mee.2012.12.021 ↗
36. 3D site specific sample preparation and analysis of 3D devices (FinFETs) by atom probe tomography10.1016/j.ultramic.2012.09.013 ↗
37. Lift-out procedures for atom probe tomography targeting nanoscale features in core-shell nanowire heterostructures10.1002/pssc.201300489 ↗
38. Preparation of nanowire specimens for laser-assisted atom probe tomography10.1088/0957-4484/25/43/435704 ↗
39. Atom probe analysis of a 3D finFET with high-k metal gate10.1016/j.ultramic.2010.12.025 ↗
40. Three-dimensional doping and diffusion in nano scaled devices as studied by atom probe tomography10.1088/0957-4484/24/27/275705 ↗
41. Dopant characterization in self-regulatory plasma doped fin field-effect transistors by atom probe tomography10.1063/1.3690864 ↗
42. Characterization of 3D dopant distribution in State of the art FinFET structures10.1017/S143192761300679X ↗
43. Identification of an intrinsic source of doping inhomogeneity in vapor–liquid–solid-grown nanowires10.1021/nl3038695 ↗
44. Direct measurement of dopant distribution in an individual vapour–liquid–solid nanowire10.1038/nnano.2009.51 ↗
45. Quantitative dopant distributions in GaAs nanowires using atom probe tomography10.1016/j.ultramic.2013.02.012 ↗
46. Demonstration of confined electron gas and steep-slope behavior in delta-doped GaAs-AlGaAs core–shell nanowire transistors10.1021/acs.nanolett.5b00518 ↗
47. Boron distribution in the core of Si nanowire grown by chemical vapor deposition10.1063/1.4714364 ↗
48. Jeon · 2015
49. Relative influence of surface states and bulk impurities on the electrical properties of Ge nanowires10.1021/nl901548u ↗
50. D. Melkonyan, C. Fleischmann, L. Arnoldi, J. Bogdanowicz, A. Kumar, A. Veloso, W. Vandervorst, 3D dopant profiling in silicon nanowires, 2016, Unpublished results.
51. Advance in multi-hit detection and quantization in atom probe tomography10.1063/1.4770120 ↗
52. Effects of detector dead-time on quantitative analyses involving boron and multi-hit detection events in atom probe tomography10.1016/j.ultramic.2015.07.009 ↗
53. Analysis of implanted silicon dopant profiles10.1016/j.ultramic.2012.10.005 ↗
54. Characterizing atomic composition and dopant distribution in wide band gap semiconductor nanowires using laser-assisted atom probe tomography10.1021/jp2047823 ↗
55. Atom probe tomography in nanoelectronics10.1051/epjap/2014140060 ↗
56. 3D analysis of advanced nano-devices using electron and atom probe tomography10.1016/j.ultramic.2013.10.001 ↗
57. Three dimensional imaging and analysis of a single nano-device at the ultimate scale using correlative microscopy techniques10.1063/1.4921352 ↗
58. D. Melkonyan, C. Fleischmann, L. Arnoldi, J. Demeulemeester, A. Kumar, J. Bogdanowicz, F. Vurpillot, W. Vandervorst, Atom Probe Tomography Analysis of SiGe Fins embedded in SiO2: Facts and Artefacts, 2016, Unpublished results.10.1016/j.ultramic.2017.04.006 ↗
59. Emitter shape evolution during field evaporation and its impact on the reconstructed data of SiGe fins embedded in SiO2
60. On the Use of simulated field-evaporated specimen apex shapes in atom probe tomography data reconstruction10.1017/S1431927612001523 ↗
61. Towards an accurate volume reconstruction in atom probe tomography10.1016/j.ultramic.2016.03.008 ↗
62. A. Kumar, J. Bogdanowicz, M. Gilbert, F. Moyon, C. Fleischmann, D. Melkonyan, L. Arnoldi, J. Houard, A. Vella, W. Vandervorst, Wavelength dependence of the apex shape of a semiconducting field emitter in laser-assisted Atom Probe Tomography, 2016, Unpublished results.
63. Quantitative depth profiling of SiGe-multilayers with the Atom Probe10.1002/sia.3544 ↗
64. A. Kumar, Qualitative and quantitative analysis of compound semiconductors using Atom Probe Tomography, KULeuven, 2016.
65. W. Vandervorst, M. Meuris, Method for resistance measurements on a semiconductor element with controlled probe pressure, 1994.
66. Characterization of a point-contact on silicon using force microscopy-supported resistance measurements10.1063/1.113636 ↗
67. Crystal data for high-pressure phases of silicon10.1103/PhysRevB.34.4679 ↗
68. Evolution of metastable phases in silicon during nanoindentation: mechanism analysis and experimental verification10.1088/0957-4484/20/30/305705 ↗
69. Analysis and modeling of the high vacuum scanning spreading resistance microscopy nanocontact on silicon10.1116/1.3273895 ↗
70. Conductive diamond tips with sub-nanometer electrical resolution for characterization of nanoelectronics device structures10.1002/pssa.200982212 ↗
71. Subnanometer Characterization of Nanoelectronic Devices
72. Diamond scanning probes with sub-nanometer resolution for advanced nanoelectronics device characterization10.1016/j.mee.2016.02.053 ↗
73. Bhushan · 2008
74. A. Schulze, Two- and three-dimensional dopant and conductivity profiling in confined volumes, 2013.
75. J. Mody, G. Zschatzsch, S. Kolling, A. De Keersgieter, G. Eneman, A.K. Kambham, C. Drijbooms, A. Schulze, T. Chiarella, N. Horiguchi, T.-Y. Hoffmann, P. Eyben, W. Vandervorst, 3D-carrier profiling in FinFETs using scanning spreading resistance microscopy, in: Proceedings of the 2011 IEEE International Electron Devices Meeting, 2011, pp. 119–122. 10.1109/IEDM.2011.6131498.10.1109/IEDM.2011.6131498 ↗
76. Quantitative three-dimensional carrier mapping in nanowire-based transistors using scanning spreading resistance microscopy10.1016/j.ultramic.2012.10.008 ↗
77. U. Celano, L. Goux, A. Belmonte, A. Schulze, K. Opsomer, C. Detavernier, O. Richard, H. Bender, M. Jurczak, W. Vandervorst, Conductive-AFM tomography for 3D filament observation in resistive switching devices, in: Proceedings of the 2013 IEEE International Electron Devices Meeting, 2013, pp. 21.6.1–21.6.4. 10.1109/IEDM.2013.6724679.10.1109/IEDM.2013.6724679 ↗
78. Insights into the nanoscale lateral and vertical phase separation in organic bulk heterojunctions via scanning probe microscopy10.1039/C5NR08765A ↗
79. Atomic scale friction and wear of mica10.1016/0039-6028(94)00846-9 ↗
80. Three-dimensional carrier profiling of InP-based devices using scanning spreading resistance microscopy10.1063/1.1490399 ↗
81. Three-dimensional carrier profiling of individual Si nanowires by scanning spreading resistance microscopy10.1002/adma.201001086 ↗
82. Electrical tomography using atomic force microscopy and its application towards carbon nanotube-based interconnects10.1088/0957-4484/23/30/305707 ↗
83. U. Celano, L. Goux, A. Belmonte, G. Giammaria, K. Opsomer, C. Detavernier, O. Richard, H. Bender, F. Irrera, M. Jurczak, W. Vandervorst, Progressive vs. abrupt reset behavior in conductive bridging devices: A C-AFM tomography study, in: Proceedings of the 2014 IEEE International Electron Devices Meeting, 2014, pp. 14.1.1–14.1.4. doi:10.1109/IEDM.2014.7047048.10.1109/IEDM.2014.7047048 ↗
84. Three-dimensional observation of the conductive filament in nanoscaled resistive memory devices10.1021/nl500049g ↗
85. J. Mody, Dopant and Carrier Profiling in FinFET - Based Structures, KULeuven, 2013.
86. Outwitting the series resistance in scanning spreading resistance microscopy10.1016/j.ultramic.2015.10.029 ↗
87. A. Nazir, Scanning Spreading Resistance Microscopy for TCAD calibration in CMOS technologies, KULeuven, 2015.
88. Fast Fourier transform scanning spreading resistance microscopy: a novel technique to overcome the limitations of classical conductive AFM techniques10.1088/0957-4484/26/35/355702 ↗
89. Fast Fourier transform scanning spreading resistance microscopy: a novel technique to overcome the limitations of classical conductive AFM techniques10.1088/0957-4484/26/35/355702 ↗
90. A comprehensive model for the electrical nanocontact on germanium for scanning spreading resistance microscopy applications10.1063/1.4795141 ↗
91. M.W. Xu, Applications of Scanning Spreading Resistance Microscopy on InP-Based Materials and Devices, KULeuven, 2005.
92. Calibrated scanning spreading resistance microscopy profiling of carriers in III–V structures10.1116/1.1387458 ↗
93. Access to residual carrier concentration in ZnO nanowires by calibrated scanning spreading resistance microscopy10.1063/1.4945100 ↗
94. Scanning capacitance and spreading resistance microscopy of SiC multiple-pn-junction structure10.1143/JJAP.41.L40 ↗