On the nature and removal of saw marks on diamond wire sawn multicrystalline silicon wafers
Source abstract
Abstract
Abstract Clearly visible saw marks are a significant barrier to commercial use of diamond wire sawn multicrystalline silicon wafers for solar cells. Two types of saw marks on the diamond-cut multicrystalline silicon wafers are identified—the millimeter scale round-run fringes caused by round-running of the saw wires, and the micron scale scratches caused by scribing of the diamond tips. The latter consists of smooth and shiny grooves covered by a thin layer of amorphous phase. The micro-roughness of diamond-cut wafers is actually ~25% less than that of the conventional slurry-cut wafers. The reason for the visibility of the round-run fringes to naked eyes, and for the relatively rough appearance of diamond-cut wafers, is the visual enhancement from the shiny scratches. Therefore, the key to remove the round-run fringes is to roughen the smooth grooves, as flattening the very slightly sloped fringe zones is very difficult due to lack of chemical contrast over them. Acid-etching texturization cannot remove the saw marks on the diamond-cut silicon wafers. Alkaline-etching can only remove the saw marks on grains near (0 0 1) orientation. A vapor blast etching method has been attempted. The preliminary result is encouraging—complete removal of the saw marks has been achieved, along with a good surface texture, which reduces the light reflectivity to 19%.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Surface Polishing Techniques · Diamond and Carbon-based Materials Research · Integrated Circuits and Semiconductor Failure Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (16)
Show source-provided references
1. Y. Kondo, N. Watanabe, D. Ide, T. Matsuki, H. Takato, I. Sakata, in: Proceedings of the 23rd European Photovoltaic Solar Energy Conference and Exhibition, Valencia, Spain, September 2008, pp. 1297–1300.
2. Watanabe · Prog. Photovoltaics Res. Appl. · 2010 · 18 · 48510.1002/pip.923 ↗
3. A. Holt, A. Thogersen, C. Rohr et al., in: Proceedings of the Photovoltaic Specialists Conference (PVSC), 2010 35th IEEE. Honolulu, HI, USA, 2010, pp. 003501–003504.10.1109/PVSC.2010.5614103 ↗
4. E. Cai, B. Tang, W. Fahrner, L. Zhou, in: Proceedings of the 26th European Photovoltaic Solar Energy Conference and Exhibition. Hamburg, Germany, 2011, pp. 1884–1886.
5. M. Radet, P. Jaffrennou, N. Habka, C. Takchi, E. Abric, J. Penaud, B. Lombardet, in: Proceedings of the 27th European Photovoltaic Solar Energy Conference and Exhibition. Frankfurt, Germany, September 2012, pp. 794–797.
6. Lippold · Sol. Energy Mater. Sol. Cells · 2014 · 127 · 10410.1016/j.solmat.2014.04.006 ↗
7. Yu · Sol. Energy Mater. Sol. Cells · 2012 · 98 · 33710.1016/j.solmat.2011.11.028 ↗
8. S. Patzig-Klein, M. Schumann, R. Dechant-Wagner, S. Xu, L. Zanger, J. Wu, F. Delahaye, J. Schweckendiek, A. Heeren, H. Nussbaumer, in: Proceedings of the 28th European Photovoltaic Solar Energy Conference and Exhibition. Paris, 2013, pp. 1761–1764.
9. A. Bidiville, K. Wasmer, R. Kraft et al., in: Proceedings of the 24th European Photovolatic Solar Energy Conference and Exhibition. Hamburg, Germany, 2009.
10. A. Bidiville, J. Heiber, K. Wasmer et al., in: Proceedings of the 25th European Photovoltaic Solar Energy Conference and Exhibition. Valencia, Spain, 2010, pp. 1673–1676.
11. Tang · J. Phys. D: Appl. Phys. · 2006 · 39 · 367410.1088/0022-3727/39/16/022 ↗
12. Cheong · Nanotechnology · 2000 · 11 · 17310.1088/0957-4484/11/3/307 ↗
13. H. Wu, C. Yang, S. Melkote, S. Danyluk, in: Proceedings of the 28th European Photovoltaic Solar Energy Conference and Exhibition. Paris, 2013, pp. 1470–1473
14. Meinel · Energy Procedia · 2012 · 27 · 33010.1016/j.egypro.2012.07.072 ↗
15. Meinel · Mater. Sci. Semicond. Process. · 2014 · 26 · 9310.1016/j.mssp.2014.03.046 ↗
16. Takato H., Sakata I., Mase K., Ishibashi S., Harada T., Kondo Y., Asai Y. Method for fabricating substrate for solar cell and solar cell, US Patent 20130306148 A1, Nov., 2013.