Chemical-mechanical polishing improvements and subsurface damage elimination for Cz grown (010) β-Ga2O3 substrates
Source abstract
Abstract
An “Optimized Low pH Chemical-Mechanical Polishing (CMP) Process” was developed for manufacturing epi-ready 50 mm (010) gallium oxide (β-Ga 2O 3) substrates from Czochralski (Cz) grown boules. Using a “Pre-Epi Surface Evaluation” method, high-resolution x-ray diffraction (HRXRD), and microscopy, the baseline CMP steps previously reported for (010) β-Ga 2O 3 substrates were observed to induce significant subsurface damage (SSD). With careful selection of the polishing pad, slurry, and pressure to balance the chemical and mechanical components of the CMP process, SSD is effectively eliminated. In particular, reducing the colloidal silica slurry pH to ∼4 on a poromeric pad enables the use of higher pressures up to 3.0 psi (20.68 kPa) while maintaining a balanced CMP process. From a manufacturing perspective, this reduces cycle time by increasing the material removal rate (MRR) and helps to improve flatness and uniformity for large-area substrates. This CMP process was implemented for sets of full 50 mm Fe-doped (010) β-Ga 2O 3 substrates. These improvements resulted in an increased MRR with corresponding 1.5-2x reductions in average surface roughness (Sa/Sq) and x-ray rocking curve (XRRC) (020) full-width at half-maximum (FWHM) values. Elimination of virtually all SSD was also observed while achieving the lowest average surface roughness values (Sq ∼0.1 nm) reported for epi-ready β-Ga 2O 3 substrates to date.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Ga2O3 and related materials · ZnO doping and properties · Electronic and Structural Properties of Oxides
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (37)
Show source-provided references
1. "Recent progress in Ga2O3 power devices," Semicond. Sci
2. A review of Ga2O3 materials, processing, and devices
3. β-Gallium oxide power electronics
4. Manufacturing challenges of Czochralski growth and fabrication of 2-inch Semi-insulating β-Ga2O3 substrates
5. "Growth and fundamentals of bulk β-Ga2O3 single crystals," J
6. "High-quality β-Ga2O3 single crystals grown by edge-defined film-fed growth," Jpn
7. "Step-flow growth in homoepitaxy of β-Ga2O3 (100) - the influence of the miscut direction and faceting,"
8. Lateral β-Ga2O3 field effect transistors
9. Substrate-orientation dependence of β-Ga2O3 (100), (010), (001), and (-201) homoepitaxy by indium-mediated metal exchange catalyzed molecular beam epitaxy (MEXCAT-MBE)
10. "Towards smooth (010) β-Ga2O3 films homoepitaxially grown by plasma assisted molecular beam epitaxy: the impact of substrate offcut and metal-to-oxygen flux ratio,"
11. "Optimization of chemical mechanical polishing of (010) β-Ga2O3,"10.1116/6.0002241 ↗
12. "Close atomic surface on aluminum alloy using green chemical mechanical polishing with synergistic effect between yttria and silica abrasives," Appl. Surf
13. "Atomic surface on fused silica induced by novel green photochemical mechanical polishing," Surf
14. "Atomic level surface on aspheric quartz crucible with large sizes induced by developed green chemical mechanical polishing with composite rare earth oxides," Surf
15. "Angstrom surface on copper induced by novel green chemical mechanical polishing using ceria and silica composite abrasives," Appl. Surf
16. "Chemical mechanical polishing for sapphire wafers using a developed slurry," J. Manuf
17. "Development of mesoporous abrasives and its unprecedented polishing performance elucidated by a novel atomic model," Mater
18. "Atomic-scale planarization surface of quartz glass induced by novel green chemical mechanical polishing using three ingredients," Mater
19. "A novel slurry for chemical mechanical polishing of single crystal diamond," Appl. Surf
20. "Atomic surface of silicon wafers induced by grafted silica nanoparticles and sodium carbonate," Appl. Surf
21. "Review on chemical mechanical polishing for atomic surfaces using advanced rare earth abrasives," J. Phys. D: appl
22. "Novel full-scale model verified by atomic surface and developed composite microfiber and slurry polishing system," Compos
23. "Fabrication of hexagonal GaN on the surface of β-Ga2O3 single crystal by nitridation with NH3," Thin Solid Films,
24. Fabrication and characterization of transparent conductive Sn-doped β-Ga2O3 single crystal10.1002/pssc.200674884 ↗
25. "Atomically controlled surfaces with step and terrace of β-Ga2O3 single crystal substrates for thin film growth," Appl. Surf
26. "Effect of OH- on chemical mechanical polishing of β-Ga2O3 (100) substrate using an alkaline slurry," RSC Adv.,
27. "Effect of chemical action on the chemical mechanical polishing of β-Ga2O3(100) substrate," Precision Engineering,
28. "Effect of abrasive grit shape on polishing of β-Ga2O3(100) substrate," Precision Engineering,
29. "Development of large diameter semi-insulating gallium oxide (Ga2O3) substrates,"10.1109/TSM.2019.2944526 ↗
30. "Subsurface damage evolution of β-Ga2O3 (010) substrates during lapping and chemical mechanical polishing," J
31. "Subsurface-damaged layer in (010)-oriented β-Ga2O3 substrates," Jpn10.1007/978-3-030-47098-2 ↗
32. The effect of 4H-SiC substrate surface scratches on chemical vapor deposition grown homo-epitaxial layer quality
33. "A review of recent progress in β-Ga2O3 epitaxial growth: effect of substrate orientation and precursors in metal–organic chemical vapor deposition," phys
34. "Recent advances in the growth of gallium oxide thin films employing various growth techniques - a review," J. Phys. D: appl
35. "Slip system analysis and X-ray topographic study on β-Ga2O3," Superlattices Microstruct.,
36. "Slip planes in monoclinic β-Ga2O3 revealed from its {010} face via synchrotron X-ray diffraction and X-ray topography," Jpn
37. "Multimodal microscopy of extended defects in β-Ga2O3 (010) EFG crystals,"