Effect of grinding damage on cutting force and ductile machining during single grain scratching of monocrystalline silicon
Source abstract
Abstract
Understanding the initiating and suppression mechanisms of existing defects are the key to optimizing the ultra-precision grinding process of hard and brittle materials. This paper discusses the effects of grinding damage on material removal mechanism from the perspectives of residual scratch depth, scratch morphology and normal scratching force, through conducting the contrast variable-depth nano-scratch experiment on polished and ground monocrystalline silicon and establishing the single grain scratching Smoothed Particle Hydrodynamics (SPH) model. The experimental and simulation results show that radial crack on ground silicon surface is almost invisible due to the existence of grinding marks, which indicates that it is difficult to judge the ductile brittle transition (DBT) point by the traditional method of observing cracks. With the increase of penetration depth, pop-in will occur in the residual scratch depth of polished and ground silicon, indicating that the material removal mode has transformed, which provides an important basis for judging the DBT point. The DBT critical normal scratching force (38.93 mN) and residual scratch depth (−0.14 μm) of ground silicon are much higher than those of polished silicon, implying ground silicon is easier to achieve ductile processing. Meanwhile, when the penetration depth is the same, compared to polished silicon, the normal scratching force of ground silicon is generally larger. Finally, a single grain scratching SPH model of pre-stressed silicon is established. And the simulated phenomenon and conclusions are consistent with the experiment, which proves that the surface compressive stress is an important factor that causes the removal characteristics of ground silicon to be different from polished silicon. This study provides a theoretical basis for understanding the ultra-precision grinding removal mechanism of hard and brittle materials.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Surface Polishing Techniques · Advanced machining processes and optimization · Metal and Thin Film Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (45)
Show source-provided references
1. Novel fabrication for vertically stacked inverted triangular and diamond-shaped silicon nanowires on (100) single crystal silicon wafer [J]10.1088/1361-6439/ab5125 ↗
2. Finite element simulation and experimental research on microcutting mechanism of single crystal silicon [J]
3. Grinding of silicon wafers: a review from historical perspectives [J]10.1016/j.ijmachtools.2008.05.009 ↗
4. Formation of subsurface cracks in silicon wafers by grinding [J]10.1016/j.npe.2018.09.003 ↗
5. Prediction of subsurface damage depth in rotary ultrasonic machining of glass BK7 with probability statistics [J]
6. Analytical modeling of grinding-induced subsurface damage in monocrystalline silicon [J]10.1016/j.matdes.2017.05.068 ↗
7. New insights into the methods for predicting ground surface roughness in the age of digitalisation10.1016/j.precisioneng.2020.11.001 ↗
8. Investigation on critical crack-free cutting depth for single crystal silicon slicing with fixed abrasive wire saw based on the scratching machining experiments [J]10.1016/j.mssp.2017.10.027 ↗
9. Modeling and simulation of phase transformation and crack formation during scribing of mono-crystalline silicon [J]10.1016/j.ijmecsci.2020.105527 ↗
10. Interaction of lateral cracks in double scratching of single-crystal silicon carbide [J]10.1016/j.tafmec.2019.102378 ↗
11. Scratch with double-tip tool: crack behavior during simultaneous double scratch on BK7 glass [J]10.1016/j.jeurceramsoc.2020.04.008 ↗
12. Material removal mechanism and deformation characteristics of AlN ceramics under nanoscratching [J]10.1016/j.ceramint.2019.07.034 ↗
13. Surface defects incorporated diamond machining of silicon [J]10.1088/2631-7990/abab4a ↗
14. A theoretical assessment of surface defect machining and hot machining of nanocrystalline silicon carbide [J]10.1115/1.4026297 ↗
15. An experimental investigation for the improvement of attainable surface roughness during hard turning process [J]10.1177/0954405412464217 ↗
16. Advances in the surface defect machining (SDM) of hard steels [J]10.1016/j.jmapro.2016.05.007 ↗
17. The development of a surface defect machining method for hard turning processes [J]10.1016/j.wear.2013.01.048 ↗
18. Smooth particle hydrodynamics study of surface defect machining for diamond turning of silicon [J]10.1007/s00170-016-8940-6 ↗
19. Influences of residual stress induced by cutting on subsequent scratch using smooth particle hydrodynamic (SPH) [J]10.2320/matertrans.M2014078 ↗
20. Surface quality and residual stress variation of ceramics after abrasive grinding under pre-compressive stress [J]10.1016/j.ceramint.2020.09.203 ↗
21. Numerical simulation of chipping formation process with smooth particle hydrodynamic (SPH) method for diamond drilling AIN ceramics [J]10.1007/s00170-018-1724-4 ↗
22. Smoothed-particle hydrodynamics investigation on brittle–ductile transition of quartz glass in single-grain grinding process [J]10.1007/s41871-020-00075-2 ↗
23. Smoothed particle hydrodynamics simulation and experimental analysis of SiC ceramic grinding mechanism [J]10.1016/j.ceramint.2018.03.278 ↗
24. Theoretical modeling and experimental analysis of single-grain scratching mechanism of fused quartz glass [J]10.1016/j.jmatprotec.2021.117090 ↗
25. Cup wheel grinding-induced subsurface damage in optical glass BK7: an experimental, theoretical and numerical investigation [J]10.1016/j.precisioneng.2019.04.003 ↗
26. Analysis of grit interference mechanisms for the double scratching of monocrystalline silicon carbide by coupling the FEM and SPH [J]10.1016/j.ijmachtools.2017.04.012 ↗
27. Analytical prediction for depth of subsurface damage in silicon wafer due to self-rotating grinding process [J]10.1016/j.cap.2019.02.015 ↗
28. An etch for delineation of defects in silicon [J]10.1149/1.2115767 ↗
29. Li · 2020
30. Some experiments on the scratching of silicon: in situ scratching inside an SEM and scratching under high external hydrostatic pressures10.1016/S0020-7403(00)00019-9 ↗
31. Geometrical effects in elastic/plastic indentation [J]10.1111/j.1151-2916.1984.tb19148.x ↗
32. Speed effect on the material behavior in high-speed scratching of BK7 glass [J]10.1016/j.ceramint.2021.04.008 ↗
33. Subsurface damage measurement of ground fused silica parts by HF etching techniques [J]10.1364/OE.17.020448 ↗
34. Effect of grinding wheel spindle vibration on surface roughness and subsurface damage in brittle material grinding [J]10.1016/j.ijmachtools.2015.01.003 ↗
35. Surface roughness and subsurface damage characterization of fused silica substrates [J]
36. A load identification method for the grinding damage induced stress (GDIS) distribution in silicon wafers [J]10.1016/j.ijmachtools.2016.04.010 ↗
37. Residual stress distribution in silicon wafers machined by rotational grinding [J]10.1115/1.4036125 ↗
38. Smoothed particle hydrodynamics: theory and application to non-spherical stars [J]10.1093/mnras/181.3.375 ↗
39. A smoothed particle hydrodynamics (SPH) model for simulating surface erosion by impacts of foreign particles [J]10.1016/j.triboint.2015.11.038 ↗
40. Material removal behavior in ultrasonic-assisted scratching of SiC ceramics with a single diamond tool [J]10.1016/j.ijmachtools.2014.02.002 ↗
41. Application of dynamic relaxation method in finite element static-solution of strain-softening-type structure [J]
42. First-principles equation-of-state table of silicon and its effects on high-energy-density plasma simulations [J]
43. Experimental and simulation studies of abrasive particles impacting monocrystalline silicon in suspension thin film flow field of ultrasonic polishing [J]10.1007/s00170-019-03580-x ↗
44. An improved computational constitutive model for brittle materials [C]//AIP conference proceedings
45. Study of the influence of tool rake angle in ductile machining of optical quartz glass [J]10.1007/s00170-019-03920-x ↗