journal article·2026-03-13

Enhancing tribological performance of Kevlar–PLA nanocomposites through sustainable optimization of fused deposition modeling parameters using RSM and machine learning

M Balu, S Ayyanar, G Suresh, R Manikandan

Publisher page

Abstract

This study optimizes fused filament fabrication (FFF) parameters to enhance the tribological performance of Kevlar fibre–reinforced polylactic acid (PLA) nanocomposites. Filaments containing 0–10 wt-% Kevlar were produced by twin-screw extrusion and characterized for mechanical and thermal behavior. A 30-run central composite design evaluated the effects of layer height (0.1–0.3 mm), build orientation (0–90°), wall width (0.2–0.6 mm), and Kevlar content on specific wear rate. Statistical analysis identified layer height as the dominant factor (F = 2336.47), contributing 83.3% of the total variation. Predictive modeling using ANN and adaptive neuro-fuzzy inference systems ANFIS demonstrated superior accuracy for ANFIS (R 2 = 0.9985 training, 0.9912 validation, 0.9647 testing). The optimized parameter set yielded a minimum wear rate of 0.0187 mm 3 /s with 1.06% prediction error, validated using functional spur gear testing.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Natural Fiber Reinforced Composites · Tribology and Wear Analysis · Additive Manufacturing and 3D Printing Technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Anna University Regional Campus

Saveetha School of Engineering

Saveetha University

Rajalakshmi Institute of Technology

References (46)

Show source-provided references
1. 10.1016/j.polymertesting.2020.10656110.1016/j.polymertesting.2020.106561 ↗
2. 10.1016/j.polymertesting.2020.10665610.1016/j.polymertesting.2020.106656 ↗
3. 10.3390/polym1708105410.3390/polym17081054 ↗
4. 10.1016/S0921-5093(00)01810-410.1016/S0921-5093(00)01810-4 ↗
5. 10.1016/j.jare.2011.05.00110.1016/j.jare.2011.05.001 ↗
6. 10.1007/s00170-015-7576-210.1007/s00170-015-7576-2 ↗
7. Morales NG, Fleck TJ, Rhoads JF. The effect of interlayer cooling on the mechanical properties of components printed via fused deposition. Addit Manuf 2018; 24: 243–248.
8. 10.3390/polym1712160110.3390/polym17121601 ↗
9. 10.3390/ma1007074810.3390/ma10070748 ↗
10. Gonçalves C, Pinto A, Machado AV, et al. Biocompatible reinforcement of poly(lactic acid) with graphene nanoplatelets. Polym Compos 2016; 39: E308–E320.
11. 10.1080/10601325.2017.125031110.1080/10601325.2017.1250311 ↗
12. Lin AD, Kuang JH. Dynamic interaction between contact loads and tooth wear of engaged plastic gear pairs. Int J Mol Sci 2008; 50: 205–213.
13. 10.1515/polyeng-2013-003910.1515/polyeng-2013-0039 ↗
14. 10.1038/nature2427010.1038/nature24270 ↗
15. 10.1038/nature1453910.1038/nature14539 ↗
16. 10.1126/science.aaa841510.1126/science.aaa8415 ↗
17. 10.1038/s41586-018-0337-210.1038/s41586-018-0337-2 ↗
18. 10.1039/D0MH01451F10.1039/D0MH01451F ↗
19. 10.1016/j.polymertesting.2022.10791010.1016/j.polymertesting.2022.107910 ↗
20. 10.1016/j.nxmate.2025.10093210.1016/j.nxmate.2025.100932 ↗
21. 10.1007/s12008-019-00536-z10.1007/s12008-019-00536-z ↗
22. 10.1007/s12008-024-01853-810.1007/s12008-024-01853-8 ↗
23. 10.1016/j.tws.2021.10771710.1016/j.tws.2021.107717 ↗
24. 10.1088/2053-1591/abc8bd10.1088/2053-1591/abc8bd ↗
25. 10.1016/j.polymertesting.2023.10812910.1016/j.polymertesting.2023.108129 ↗
26. Presti DL, Bianchi D, Massaroni C, et al. Optimization and characterization of a 3D-printed wearable strain sensor for respiration and heartbeat measurements. Measurement (Mahwah N J) 2024; 228: 114377.
27. 10.1007/s00170-014-5796-510.1007/s00170-014-5796-5 ↗
28. 10.1016/j.polymertesting.2022.10754510.1016/j.polymertesting.2022.107545 ↗
29. Singh B, Kumar R, Chohan J, et al. Investigation of copper reinforced acrylonitrile butadiene styrene and nylon 6 based thermoplastic polymer nanocomposite filaments for 3D printing of electronic components. High Perform Polym 2022; 34: 09540083221112307.
30. 10.1007/s00170-019-03626-010.1007/s00170-019-03626-0 ↗
31. 10.1177/152808371774076510.1177/1528083717740765 ↗
32. 10.1016/j.wear.2008.12.02610.1016/j.wear.2008.12.026 ↗
33. 10.1038/s41598-025-17304-710.1038/s41598-025-17304-7 ↗
34. 10.3390/polym1514305310.3390/polym15143053 ↗
35. 10.3390/polym1109148710.3390/polym11091487 ↗
36. 10.1016/j.cag.2021.10.00610.1016/j.cag.2021.10.006 ↗
37. 10.1016/j.compscitech.2014.10.00910.1016/j.compscitech.2014.10.009 ↗
38. 10.1016/j.compositesb.2015.06.01310.1016/j.compositesb.2015.06.013 ↗
39. 10.1016/j.hybadv.2025.10051010.1016/j.hybadv.2025.100510 ↗
40. 10.1108/RPJ-01-2024-000710.1108/RPJ-01-2024-0007 ↗
41. 10.1016/j.compositesb.2019.10714710.1016/j.compositesb.2019.107147 ↗
42. 10.3390/polym1713179210.3390/polym17131792 ↗
43. 10.18063/ijb.73410.18063/ijb.734 ↗
44. 10.3390/polym1511245110.3390/polym15112451 ↗
45. 10.1016/j.compositesb.2021.10933210.1016/j.compositesb.2021.109332 ↗
46. 10.3390/polym1520411210.3390/polym15204112 ↗