journal article·2025-08-14

Investigation of microstructure and mechanical properties of high-Mn Fe-Mn-Al-C cryogenic steel in as-forged state

Xiaofeng Zhang, Lele Dai, Xinlei Zhao, Zhongyong Yang, Yong Yang

Publisher page

Abstract

Three high-Mn cryogenic steels were developed, with the 24Mn4Al and 26Mn6Al alloys show superior cryogenic performance due to the combined effects of the twinning-induced plasticity (TWIP) effect and the γ/δ duplex phase structure. At −196 °C, these steels achieved yield strengths of 527 MPa and 639 MPa, and ultimate tensile strengths of 970 MPa and 977 MPa, for 24Mn4Al and 26Mn6Al, respectively. The 24Mn4Al steel exhibited exceptional impact toughness (200.6 J·cm −2 ) and 74.5% elongation at −80 °C. Increasing Mn/Al ratios reduced the γ/δ phase fraction while elevating the stacking fault energy (SFE), shifting the dominant deformation mechanism from TWIP to dislocation slip. This transition significantly reduced low temperature impact toughness, highlighting the critical balance between composition optimization and SFE control for cryogenic applications.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Metallurgy and Material Forming

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

School of Metallurgical Engineering, Anhui University of Technology, Maanshan, P.R. China

Funding

Natural Science Foundation of Anhui Province · University Natural Science Research Project of Anhui Province

References (48)

Show source-provided references
1. 10.1016/j.msea.2019.02.09310.1016/j.msea.2019.02.093 ↗
2. 10.1016/j.msea.2023.14576810.1016/j.msea.2023.145768 ↗
3. Chen J, Ren J, Liu Z. Deformation microstructures as well as strengthening and toughening mechanisms of low-density high Mn steels for cryogenic applications. J Mater Sci Technol 2021; 13: 947–961.
4. 10.1007/s40195-016-0496-910.1007/s40195-016-0496-9 ↗
5. 10.1016/j.msea.2018.03.05610.1016/j.msea.2018.03.056 ↗
6. 10.1016/j.actamat.2014.11.02710.1016/j.actamat.2014.11.027 ↗
7. 10.1016/j.jmrt.2023.12.02010.1016/j.jmrt.2023.12.020 ↗
8. 10.1016/j.matchar.2016.10.00510.1016/j.matchar.2016.10.005 ↗
9. 10.1088/1468-6996/14/1/01420510.1088/1468-6996/14/1/014205 ↗
10. 10.1016/j.actamat.2015.08.02710.1016/j.actamat.2015.08.027 ↗
11. 10.1016/j.actamat.2010.05.04910.1016/j.actamat.2010.05.049 ↗
12. Zhang Q, Chen G, Hu H, et al. Temperature dependence of the deformation behavior and mechanical properties of a Fe–Mn–Al–C low-density steel for cryogenic application. J Mater Sci Technol 2024; 33: 3418–3426.
13. Zhang J, Li G, Wang H, et al. Achieving superior cryogenic impact toughness and sufficient tensile properties in a novel high-Mn austenitic steel weld metal via cerium addition. J Mater Sci Technol 2023; 23: 5016–5030.
14. 10.1016/j.jnucmat.2022.15398210.1016/j.jnucmat.2022.153982 ↗
15. 10.1016/j.jnucmat.2018.03.01910.1016/j.jnucmat.2018.03.019 ↗
16. 10.1016/j.ijplas.2018.11.01510.1016/j.ijplas.2018.11.015 ↗
17. Anderson PM, Hirth JP, Lothe J. Theory of dislocations. United Kingdom: Cambridge University Press, 2017.
18. 10.1016/j.actamat.2020.09.07510.1016/j.actamat.2020.09.075 ↗
19. 10.1016/j.actamat.2006.07.01310.1016/j.actamat.2006.07.013 ↗
20. 10.2355/isijinternational.43.43810.2355/isijinternational.43.438 ↗
21. 10.1016/j.msea.2010.02.05810.1016/j.msea.2010.02.058 ↗
22. 10.1016/S1359-6454(02)00594-310.1016/S1359-6454(02)00594-3 ↗
23. 10.1016/0001-6160(78)90170-010.1016/0001-6160(78)90170-0 ↗
24. 10.1016/j.actamat.2009.04.04510.1016/j.actamat.2009.04.045 ↗
25. 10.1016/j.msea.2021.14195910.1016/j.msea.2021.141959 ↗
26. 10.1016/j.scriptamat.2022.11462910.1016/j.scriptamat.2022.114629 ↗
27. 10.1016/j.matchar.2024.11434010.1016/j.matchar.2024.114340 ↗
28. Khachaturyan AG. Theory of structural transformations in solids. United States: Courier Corporation, 2013.
29. Olson GB, Cohen M. A general mechanism of martensitic nucleation: part I. General concepts and the FCC→ HCP transformation. Metall Trans A 1976; 7: 1897–1904.
30. 10.1002/srin.20220019110.1002/srin.202200191 ↗
31. 10.1016/j.msea.2006.12.17010.1016/j.msea.2006.12.170 ↗
32. 10.1016/j.scriptamat.2005.07.00210.1016/j.scriptamat.2005.07.002 ↗
33. 10.1016/j.scriptamat.2019.08.02510.1016/j.scriptamat.2019.08.025 ↗
34. 10.1016/0956-716X(94)90611-410.1016/0956-716X(94)90611-4 ↗
35. 10.1361/10599490077034543010.1361/105994900770345430 ↗
36. 10.1016/j.scriptamat.2025.11666810.1016/j.scriptamat.2025.116668 ↗
37. 10.3390/ma1713311710.3390/ma17133117 ↗
38. 10.1016/j.msea.2017.07.08610.1016/j.msea.2017.07.086 ↗
39. 10.1016/j.msea.2023.14567510.1016/j.msea.2023.145675 ↗
40. 10.3390/met1210157210.3390/met12101572 ↗
41. 10.1016/j.actamat.2016.07.03410.1016/j.actamat.2016.07.034 ↗
42. 10.1126/science.ado291910.1126/science.ado2919 ↗
43. 10.1016/j.actamat.2020.03.02210.1016/j.actamat.2020.03.022 ↗
44. 10.1016/j.msea.2022.14433010.1016/j.msea.2022.144330 ↗
45. 10.1016/j.scriptamat.2019.02.01310.1016/j.scriptamat.2019.02.013 ↗
46. 10.2355/isijinternational.ISIJINT-2020-46710.2355/isijinternational.ISIJINT-2020-467 ↗
47. Li X Liu R Hou JP et al. Trade-off model for strength-ductility relationship of metallic materials. Available at SSRN 5015525.
48. 10.1002/adem.20150010810.1002/adem.201500108 ↗