journal article·2025-04-22

Distribution of the residual stress on Ti600/TC18 joint welded by inertial friction welding

Ying-Ying Liu, Xuan Liu, Jun-Yi Zhang, Kai-Xin Ren, Chun Li, Feng Wang, Shi-Feng Liu, Wen Wang, Kuai-She Wang

Publisher page

Abstract

In this study, the Ti600/TC18 dissimilar alloy parts were joined by inertia friction welding, which is mainly used in aerospace industry as structural components. Then the investigation of the residual stress distribution in the inertial friction welded joint of Ti600/TC18, both pre-and post-weld heat treatment, was carried out using ABAQUS software and XRD. The results show that the highest temperature during the welding is up to 1200 °C; it is subjected to tensile stress. As the welding goes on, the range of tensile stress is expanded gradually, and it is up to 8.92 MPa. During the welding, dynamic recrystallization is occurred in the weld zone, so the refined dynamic recrystallization grains are formed. After heat treatment, the martensitic transformation is occurred within the β phase, so the α p , acicular α, α s and residual β phase are existed in the weld zone. Moreover, the heat treatment has an obvious effect on the distribution of longitudinal residual stress, which can promote the residual stress field to be distributed more uniform and gradual. In addition, the peak tensile stress on the weld surface can be reduced effectively by stress relief annealing, which is attributed to the obvious growth of grain and the coarsening of lath-like α phase in the joint. Finally, comparing the test values with the simulation values, the later exhibits better accuracy and stability.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Welding Techniques and Residual Stresses · Titanium Alloys Microstructure and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

School of Metallurgical Engineering, Xi’an University of Architecture and Technology, Xi’an 710055, People's Republic of China

National and Local Joint Engineering Research Center for Functional Materials Processing, Xi'an University of Architecture and Technology, Xi'an 710055, People's Republic of China

National Defense Key Disciplines Laboratory of Light Alloy Processing Science and Technology, Nanchang Hangkong University, Nanchang 330063, People's Republic of China

School of Metallurgy and Materials, The University of Birmingham, Elms Road, Edgbaston, Birmingham, B15 2SE, UK

Funding

Xi'an Science and Technology Program · Nanchang Hangkong University

References (29)

Show source-provided references
1. 10.1016/j.matpr.2021.09.06610.1016/j.matpr.2021.09.066 ↗
2. 10.3390/ma1303055210.3390/ma13030552 ↗
3. 10.1007/s10853-021-06599-210.1007/s10853-021-06599-2 ↗
4. 10.1016/j.msea.2023.14480710.1016/j.msea.2023.144807 ↗
5. 10.3390/ma1601039210.3390/ma16010392 ↗
6. Li ZS, Xiong ZH, Yang P, et al. Simulation of texture evolution of large TC18 titanium alloy bar during multi-pass forging. Rare Met Mater Eng 2022; 51: 2446–2453.
7. Cheng RH Zhang ZS Ruan WB et al. Core key technologies of advanced aircraft engine. Acta Aeronaut Astronaut Sin. Epub ahead of print 17 December 2024. https://hkxb.buaa.edu.cn/CN/10.7527/S1000-6893.2024.31220
8. Liu WM, Ouyang K, Zhang XM, et al. Influence of post-weld heat treatment on residual stress of welded joint of S30408 / Q345R clad plate. T Mater Heat Treat 2023; 44: 217–226.
9. Wang ZP, Zhang HM, Fu KJ, et al. Characteristics of bonding interface and analysis of properties of hot-rolled 304L/ Q235B stainless steel clad plate. T Mater Heat Treat 2016; 37: 44–49.
10. 10.4028/p-o8uehr10.4028/p-o8uehr ↗
11. 10.1016/j.msea.2023.14499110.1016/j.msea.2023.144991 ↗
12. 10.1016/j.ijpvp.2010.08.01010.1016/j.ijpvp.2010.08.010 ↗
13. 10.1016/j.ijpvp.2022.10485210.1016/j.ijpvp.2022.104852 ↗
14. 10.1016/j.ijpvp.2014.06.00210.1016/j.ijpvp.2014.06.002 ↗
15. Wang XP, Li L, Zhang XY, et al. Constitutive relationship and its application in finite element simulation of hot rolling of TC18 titanium alloy. Chin J Nonferrous Met 2013; 23: 379–388.
16. Qi YL, Zeng WD, Zhao YQ. Constitutive equations for hot deformation of Ti600 alloy. Cast Forg 2006; 05: 5–8.
17. 10.1007/s11837-024-06855-110.1007/s11837-024-06855-1 ↗
18. 10.1016/j.jmatprotec.2003.10.02510.1016/j.jmatprotec.2003.10.025 ↗
19. 10.3901/JME.2021.16.30610.3901/JME.2021.16.306 ↗
20. 10.1016/j.ijpvp.2022.10473010.1016/j.ijpvp.2022.104730 ↗
21. Luo WZ, Cheng HM, Liu HY, et al. Numerical simulation of residual stress and welding deformation of high strength steel Q960E butt-welded joints. China Mech Eng 2023; 34: 2095–2105. 2141.
22. Gerhard W, Boyer RR, Collings EW. Materials properties handbook: titanium alloys. USA: ASM International, 1994, 411–414.
23. Hong Q, Qi YL, Liu X, et al. Effects of rolling process on microstructure and properties of Ti600 alloy plates. J Aeronautical Mater 2006; 05: 31–34.
24. Du SG, Wang Q, Fu L. Analysis of tribology properties of DD3 and Renē95 at friction interlayer during friction welding. Transactions China Weld Inst 2002; 23: 27–30.
25. Li XH, Zhang YH, Li Z, et al. Effect of heat treatment temperatures on microstructure and mechanical property of linear friction welded joints of titanium alloys TC17(α+β)/TC17(β). J Mater Eng 2020; 48: 115–120.
26. Kashyzadeh KR, Farrahi G, Ahmadi A, et al. Fatigue life analysis in the residual stress field due to resistance spot welding process considering different sheet thicknesses and dissimilar electrode geometries. P I Mech Eng L-J Mater 2023; 237: 33–51.
27. 10.1016/j.ijpvp.2012.08.00210.1016/j.ijpvp.2012.08.002 ↗
28. Zhang SY, Lin X, Chen J, et al. Influence of heat treatment on residual stress of Ti-6Al-4 V alloy by laser solid forming. Rare Met Mater Eng 2009; 38: 774–778.
29. 10.1016/j.matdes.2014.11.03710.1016/j.matdes.2014.11.037 ↗