Microstructure and properties of AZ31 alloy by static recrystallisation at lower temperature
Source abstract
Abstract
The microstructure evolution and mechanical properties of AZ31 Mg sheets that was processed by rolling and subsequent annealing at lower temperature were investigated. The results indicated that few-pass rolling with large deformation is a better strategy to prepare AZ31 Mg sheets with higher deformation restored energy and less rolling defects. After annealing, the static recrystallisation occurred and the recrystallisation degree increases with the annealing temperature and time. Finally, the best comprehensive mechanical properties were obtained by 3-pass rolling with large deformation and annealing at 200 °C for 150 s and the corresponding YS, UTS and TEF of the AZ31 sheet were 225 MPa, 305 MPa and 32%, respectively. The improvement in the microstructure and mechanical properties can be attributed to an optimised static recrystallisation at a relatively low temperatures and in a short time.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Magnesium Alloys: Properties and Applications · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Key Laboratory of Interface Science and Engineering in Advanced Materials, Ministry of Education, Taiyuan University of Technology, Taiyuan, China
College of Materials Science and Engineering, Taiyuan University of Technology, Taiyuan, China
Shanxi Key Laboratory of Advanced Magnesium Based Materials, Taiyuan University of Technology, Taiyuan, China
Department of Engineering, University of Leicester, Leicester, UK
References (29)
Show source-provided references
1. Blawert C · Trans Indian Inst Met · 2004 · 57 · 397
2. 10.4028/www.scientific.net/MSF.350-351.1910.4028/www.scientific.net/MSF.350-351.19 ↗
3. 10.1016/j.matdes.2015.12.16510.1016/j.matdes.2015.12.165 ↗
4. 10.1016/j.msea.2016.09.06610.1016/j.msea.2016.09.066 ↗
5. 10.1016/j.matchemphys.2021.12459810.1016/j.matchemphys.2021.124598 ↗
6. 10.1016/j.jallcom.2012.05.00210.1016/j.jallcom.2012.05.002 ↗
7. 10.1016/j.jmatprotec.2011.04.00910.1016/j.jmatprotec.2011.04.009 ↗
8. 10.1016/j.msea.2007.09.06910.1016/j.msea.2007.09.069 ↗
9. Huang GJ · Mater Sci Forum, · 379
10. 10.1016/j.jma.2021.08.02610.1016/j.jma.2021.08.026 ↗
11. 10.1016/j.msea.2013.09.02810.1016/j.msea.2013.09.028 ↗
12. 10.1016/j.jmrt.2020.02.10310.1016/j.jmrt.2020.02.103 ↗
13. 10.1016/j.jma.2020.03.00310.1016/j.jma.2020.03.003 ↗
14. 10.1016/j.actamat.2011.12.01710.1016/j.actamat.2011.12.017 ↗
15. 10.1016/j.msea.2009.03.04510.1016/j.msea.2009.03.045 ↗
16. 10.1016/j.matchar.2011.01.00710.1016/j.matchar.2011.01.007 ↗
17. 10.1016/j.scriptamat.2009.09.00210.1016/j.scriptamat.2009.09.002 ↗
18. 10.1016/j.phpro.2013.11.01210.1016/j.phpro.2013.11.012 ↗
19. 10.1016/S0921-5093(02)00007-210.1016/S0921-5093(02)00007-2 ↗
20. 10.1016/j.msea.2006.03.02210.1016/j.msea.2006.03.022 ↗
21. Xiao B · J Mater Process Technol
22. 10.1016/j.msea.2014.06.03410.1016/j.msea.2014.06.034 ↗
23. 10.1016/j.msea.2015.04.05710.1016/j.msea.2015.04.057 ↗
24. 10.1016/S1003-6326(18)64724-710.1016/S1003-6326(18)64724-7 ↗
25. 10.1016/j.msea.2018.09.04110.1016/j.msea.2018.09.041 ↗
26. 10.1016/j.msea.2014.09.06010.1016/j.msea.2014.09.060 ↗
27. 10.1179/1743284714Y.000000068010.1179/1743284714Y.0000000680 ↗
28. 10.1016/j.matchar.2016.12.00710.1016/j.matchar.2016.12.007 ↗
29. 10.1016/j.matlet.2010.02.01710.1016/j.matlet.2010.02.017 ↗