Some aspects of cold upset forming of sintered aluminium preforms using graphite lubricant
Source abstract
Abstract
Cold upset forming and densification features in sintered aluminium preforms were investigated. Cylindrical preforms with four initial theoretical densities of 81, 85, 88 and 90% possessing three different aspect ratios of 0.50, 0.75 and 1.0 were prepared using a die and punch assembly with a 1.0 MN capacity hydraulic press. The preforms were packed in covered dry fine silica sand before the sintering operation was carried out in an electric muffle furnace at 525 ± 10 °C for a period of 1 h, and subsequently they were furnace cooled. Cold deformation experiments were conducted in incremental deformation steps. The experimental data showed that the ratio of the density of the preform after deformation/theoretical density of the fully dense material ρ f / ρ th value demonstrated an increasing trend with increasing value of exp ( ϵ z - ϵ θ ), where ϵ z is the true strain in the axial direction ϵ θ is that in the hoop direction. It was established that a lower aspect ratio preform exhibited enhanced densification compared with the higher aspect ratio preforms, for any given initial preform density. Moreover, the applied stress had the tendency to increase rapidly during the initial stage of densification, thereafter continuing to increase at a low rate, as the densification was enhanced. The increase in applied stress was found to be associated with the combined effects of densification on the geometric and general work hardening parameters.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Powder Metallurgy Techniques and Materials · Aluminum Alloys Composites Properties · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (24)
Show source-provided references
1. NARAYANASAMY R., and PANDEY K. S.: Q. Int. J. Powder Metall. Sci. Technol., 1990, 1, (2), 10–23.
2. BACKSTIEGEL G.: Powder Metall. Int, 1971,3, (1), 108–112.
3. 10.1016/S0924-0136(97)00169-610.1016/S0924-0136(97)00169-6 ↗
4. KUHN H. A. and LAWLEY A.: ‘Powder metallurgy processing’ 99–112; 1978 New York Academic Press.10.1016/B978-0-12-428450-0.50010-0 ↗
5. FISCHMEISTEN H. F. AREN B. and EASTERLING K. E.: Powder Metall. 1971 14 144–163.10.1179/pom.1971.14.27.011 ↗
6. 10.1016/0020-7403(84)90006-710.1016/0020-7403(84)90006-7 ↗
7. HEWITT R. L., , WALLACE W. and M. C. DEMALBERBE Int J. Powder Metall. Powder Technol., 1974, 10, 131–134.
8. 10.1115/1.344310410.1115/1.3443104 ↗
9. SAMUEL B.: ‘Source book on powder metallurgy’ 151-158; Sweden Hoeganaes Ltd 1979.
10. KAHLOW K. J.: ‘Void behaviour as influenced by pressure and plastic deformation’, Institute for Metal Forming report, Lehigh University, PA, USA, 1971.
11. GAIGER H. L., and LAWLEY A.: Int J. Powder Metall., 1974, 10, 21–31.
12. ANTE H. W.: ‘Deformation of porous materials’, Report, Hoeganaes Corp., Riverton, NJ, USA, 1990.
13. RAO M. N. and PANDEY K. S.: Proc. 14th AIMTDR Conf. New Delhi India 217-222; 1990 McGraw-Hill.
14. PANDEY K. S.: Proc. 15th Natl. AIMTDR Conf. India 1992 D17.
15. PANDEY K. S., , MISRA P. S., and MEHTA m. L.: Trans Powder Metall. Assoc. India, 1986, 13, 94–99.
16. PANDEY K. S., , MISRA P. S., and MEHTA m. L.: Trans Powder Metall. Assoc. India, 1988, 15, 9–14.
17. RAVINDRANATHAN S. P. PANDEY K. S. and MATHRUBOOTHAIVE K. Proc. 11th Natl. PM Conf. Jamshedpur India 1985.
18. DOWNEY C. L. JR and H. A. KUHN: Trans ASME Eng. Mater. Technol. 1975 121–125.10.1115/1.3443271 ↗
19. PANDEY K. S.: Mater. Forum, 1989, 29-31, 465–486.
20. PANDEY K. S.: Q. Int. J. Powder Metall. Sci. Technol., 1991, 2, (4), 35–44.
21. KOERNER R. M.: Powder Metall. Int, 1971,3, (4), 71–77.
22. ARTE H. W.: Proc. SME Int. Meeting PA 1971 Society of Manufacturing Engineers.
23. WAKIL S. D. EL: Proc. 12th North Am. ‘Manufacturing Research’ Conf. Houghton MI USA 1984 86.
24. 10.1016/0378-3804(88)90136-210.1016/0378-3804(88)90136-2 ↗