journal article·1998-05

Wear properties of Fe-Fe3C nanophase white iron obtained by mechanosynthesis and hot isostatic pressing

V. Porcarelli, L. Ceschini, P. Matteazzi

Materials Science and Technology· Volume 14· Issue 5
Publisher page

Abstract

Dry sliding wear tests were carried out on an Fe-Fe3C nanophase white iron, of composition 85Fe3C-15Fe (vol.-%), produced by mechanosynthesis of powders and compaction. The tests were carried out using a fiat on cylinder tribometer, with the specimens sliding against a ceramic Al2O3-TiO2 countermaterial under applied loads of 5, 10, 20, and 30 N and sliding speeds of 0.3, 1.2, and 1.8 m S−l for sliding distances up to 10 km. During the tests the coefficient of dynamic friction and total wear were recorded by means of a loading cell and a linear variable displacement transducer respectively. The depth of the wear tracks was recorded using a stylus profilometer and the worn surface was investigated by scanning electron microscopy (SEM). X-ray diffraction analysis and SEM observations were performed on the collected debris and the damage to the countermaterial was evaluated. For comparison, the same tests and analyses were carried out on a type T high speed steel and on a WC-TiC-Co composite. The Fe-Fe3C nanophase white iron underwent mild sliding wear up to F = 10 N; the type T high speed steel showed abrasive wear and the WC-TiC-Co composite showed both adhesive (low loads and sliding speeds) and abrasive (high loads and sliding speeds) wear. From the observation of the maximum depth of the wear tracks measured on the tested materials it can be noted that, at all speeds, the wear resistance of the nanophase white iron against the Al2O3-TiO2 ceramic counterface up to F = 20 N is comparable to that observedfor the T high speed steel tested in the same conditions.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Metal Alloys Wear and Properties · Advanced materials and composites · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (12)

Show source-provided references
1. 10.1016/0043-1648(93)90466-Y10.1016/0043-1648(93)90466-Y ↗
2. 10.1016/0043-1648(93)90262-K10.1016/0043-1648(93)90262-K ↗
3. II G. LAIRD · Trans. AFS · 1994 · 101 · 497
4. G. E. KORTH, T. M. LILLO, and J. C. RAWERS: in ‘Synthesis and processing of nanocrystalline powder’ (ed. David L. Boruell); 1996, Warrendale, PA, TMS.
5. 10.1016/0925-8388(94)90084-110.1016/0925-8388(94)90084-1 ↗
6. D. BASSET, P. MATTEAZZI, and M. D. ALCALA: in ‘Fundamental properties of nanostructure materials’, (ed. D. Florani and G. Sberueglieri), 30; 1994, Singapore, World Scientific Publishers.
7. P. MATTEAZZI, F. WOLF, and D. BASSET: in ‘Processing and fabrication of advanced materials’ (ed. S. Srivatsan), 97; 1996, Warrendale, PA, TMS.
8. P. MATTEAZZI, G. Le CAER, and A. MOCELLIN: in ‘Advances in science and technology 3C: ceramics - charting the future’ (ed. P. Vincenzini), 1481-1492; 1995, Faenza, Techna Srl.
9. MATTEAZZI P. · J. Hard Mater · 1991 · 2 · 171
10. 10.1111/j.1151-2916.1992.tb05499.x10.1111/j.1151-2916.1992.tb05499.x ↗
11. H. P. KLUG and L. E. ALEXANDER: `X-ray diffraction procedures', 661; 1974, New York, Wiley.
12. 10.1016/0043-1648(90)90070-Q10.1016/0043-1648(90)90070-Q ↗