journal article·2004-04

Measurements of residual strains and stresses in laser formed plates of Ti-6Al-4V using synchrotron X-ray diffraction

J. R. Cho, S. Tin, R. C. Reed

Materials Science and Technology· Volume 20· Issue 4
Publisher page

Abstract

The synchrotron X-ray diffraction technique is used to examine the development of residual strains in laser formed plates of the α - β titanium alloy Ti-6Al-4V. The following conditions were studied: (A) one pass of the laser beam; (B) three passes with intervals of 10 s between scans; (C) three passes but with 90 s intervals; (D) five passes with 10 s intervals; and (E) five passes with 90 s intervals. Measurements were made in both the longitudinal and transverse directions using the {1013} and {1120} lattice planes. The sample with five passes and 90 s intervals exhibited the largest residual stresses in the longitudinal direction, and the sample with a single pass had the lowest. The width of the zone of tensile strain was largest in the sample with five passes at 10 s intervals; next was the sample with three passes at 10 s intervals. Optical microscopy and microhardness tests demonstrated that the temperature-time history associated with condition D was sufficient to partially anneal the material, and hence low strains were observed. Needle probe distortion measurements showed that condition D resulted in the largest distortion angle (∼7.0°) while the smallest distortion (∼0.4°) was observed after condition A.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Laser and Thermal Forming Techniques · Welding Techniques and Residual Stresses · Advanced Surface Polishing Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Rolls-Royce University Technology Centre/Department of Materials Science and Metallurgy, University of Cambridge, Pembroke Street, Cambridge CB2 3QZ, UK

Department of Metals and Materials Engineering University of British Columbia, 309-6350 Stores Road, Vancouver, British Columbia V6T 1Z4, Canada

References (22)

Show source-provided references
1. HOLT R. E.: Weld Eng. 1965 September 49–52.10.1007/BF00695647 ↗
2. 10.5957/jsr.1987.31.4.26910.5957/jsr.1987.31.4.269 ↗
3. PRIDHAM M. S., and THOMSON G. A.: J. Design Manuf, 1995, 5, 203–211.
4. 10.1016/S0924-0136(97)00254-910.1016/S0924-0136(97)00254-9 ↗
5. OTSU M. OSAKADA K. and FUJII M.: in ‘Metal forming 2000’ (ed. Pietrzyk M. et al) 433–438; 2000 Krakow AGH.
6. 10.1016/S0924-0136(01)00759-210.1016/S0924-0136(01)00759-2 ↗
7. 10.1016/S0924-0136(02)00223-610.1016/S0924-0136(02)00223-6 ↗
8. 10.1016/S0924-0136(00)00860-810.1016/S0924-0136(00)00860-8 ↗
9. 10.2351/1.52184410.2351/1.521844 ↗
10. MARYA M. and EDWARDS G. R.: in ‘Trends in welding research’ (ed. Vitek J. M. et al) 982-987; 1998 Miami FL American Welding Society.
11. SPRENGER A. VOLLERTSEN F. STEEN W. M. and WATKINS K.: in ‘Laser assisted net shape engineering’ (ed. Geiger M. and Vollertsen F.) University of Erlangen Germany 1994 361–370.
12. CHO J. R.: ‘Residual stresses and distortion during the high energy power beam processing of titanium alloys’, PhD thesis, University of Cambridge, 2003.
13. CHO J. R. CONLON K. T. and REED R. C.: submitted to Metall. Mater. Trans A.
14. KRAUS I. and GANEV N.: in ‘Industrial applications of X-ray diffraction’ (ed. Chung F. H. and Smith D. K.) 793-811; 2000 New York Marcel Dekker.
15. BRANDES E. A. and BROOK G. B. (eds): ‘Smithells metals reference book’ 7th edn; 1992 Oxford Butterworth/Heinemann.
16. 10.1007/BF0133794810.1007/BF01337948 ↗
17. BEHNKEN H., and HAUK V.: Z. Metallkd., 1986, 77, 621–626.
18. 10.1063/1.36595610.1063/1.365956 ↗
19. 10.1016/S1359-0286(00)00019-X10.1016/S1359-0286(00)00019-X ↗
20. 10.1080/1023816990820012210.1080/10238169908200122 ↗
21. CHO J. R. DYE D. CONLON K. T. DAYMOND M. R. and REED R. C.: Acta Mater. 2002 50 4847–4864.10.1016/S1359-6454(02)00354-3 ↗
22. OWEN R. A. WITHERS P. J. and WEBSTER P. J.: 6th Int. Conf. on ‘Residual stresses ICRS-6’ Oxford UK July 2000 82–89.