journal article·1996-01

Characteristics of Al–Cr–Zr alloy powders made by confined nozzle atomisation

M. Lieblich, G. Caruana, M. Torralba, H. Jones

Materials Science and Technology· Volume 12· Issue 1
Publisher page

Abstract

The effects of superheat and powder particle size fraction on the characteristics of Al–5Cr–2Zr (wt-%) alloy confined nozzle atomised powder particulate has been investigated. The median powder particle size decreased from 62 to 38 μm with increase in superheat from 140 to 300 K for the atomising conditions studied, with a broadening of the size distribution and the increasing presence of large irregular powder particles at the lowest superheats. Essentially featureless α-Al based microstructures in splat caps and small sized powder particles were replaced by cellular α-Al with increasing amounts and sizes of primary L1 2 Al 3 Zr and Al 13 Cr 2 inclusions with increasing powder particle size. Refinement of the α-Al cell and intermetallic inclusion sizes in a fine compared with a coarse powder size fraction was consistent with the expected powder relationship between these variables. The decreased microhardness for coarser powder particle size fractions was attributed to the formation of increasingly coarse distributions of the primary aluminides at the expense of retention of Zr and Cr in extended solid solution. A notable age hardening response after 1h at 350–450°C for the 25–50 μm powder size fraction was consistent, however, with retention of 0·5–1·0 wt-%Zr in solid solution in this fine size fraction of the powder. MST/3163
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Intermetallics and Advanced Alloy Properties · Aluminum Alloy Microstructure Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (75)

Show source-provided references
1. PICICENS J. R.: in ‘Metals handbook’ 10 edn Vol. 2 200-215; 1990 Metals Park OH ASM International.
2. 10.1179/imr.1992.37.1.110.1179/imr.1992.37.1.1 ↗
3. DOBATKIN V. I., and ELAGIN V. I.: Soy. J. Non-ferrous Met., 1966, 7, (8), 89–93.
4. IMANOW C., , GORCZYCA S., , and PRZYBYLOWICZ K.: Arch. Hutn., 1972, 14, (4), 315–320.
5. ELAGIN V. I. and FEDEROV v. M.: Russ. Metall. 1977 (5) 193-197.
6. MIDSON S. P. JONES H. and BUCKLEY R. A.: in ‘Rapidly quenched metals’ (ed. Steeb S. and Warlimont H.) 923-926; 1985; New York Elsevier.10.1016/B978-0-444-86939-5.50220-7 ↗
7. HUGHES I. R. MARSHALL G. J. and MILLER W. S.: in ‘Rapidly quenched metals’ (ed. Steeb S. and Warlimont H. ) 1743-1746; 1985 New York Elsevier.
8. 10.1179/mst.1986.2.4.39410.1179/mst.1986.2.4.394 ↗
9. MILLER W. S. HUGHES I. R. PALMER I. G. THOMAS M. P. SAINI T. H. and WHITE J.: in ‘High strength powder metallurgy aluminum alloys II’ (ed. Hildeman G. J. and Koczak M. J. ) 311-331; 1986 Warrendale PA TMS.
10. THOMAS M. P. PALMER I. G. and BAKER C.: in ‘Processing of structural metals by rapid solidification’ (ed. Froes F. H. and Savage S. J. ) 337-345; 1987 Metals Park OH ASM International.
11. MILLER w. S., and PALMER I. G.: Met. Powder Rep., 1986, 41, 761–767.
12. PALMER I. G., and THOMAS M. P.: Metall, 1987, 41, 600–605.
13. PALMER I. G. THOMAS M. P. and MARSHALL G. J.: in ‘Dispersion strengthened aluminum alloys’ (ed. Y.-W. Kim and W. J. Griffith) 217-241; 1988 Warrendale PA TMS.
14. PARK W. W., and KIM T. H.: J. Korean Inst. Met., 1984, 22, 721–728.
15. KIM P. K., and KIM T. H.: J. Korean Inst. Met., 1984, 22, 521–528.
16. HAN S. H., and KIM T. H.: J. Korean Inst. Met., 1985, 23, 611–618.
17. PARK w. W. and Kim T. H.: in Proc. Conf. ‘Korean—Japan Proc. on rapid solidification technology’ 28-33; 1986 Metals Park OH ASM International.
18. KIM J. R., and KIM T. H.: J. Korean Inst. Met., 1987, 25, 506–513.
19. PARK w. W., and KIM T. H.: Scr. Metall, 1988, 22, (11), 1709–1714.
20. 10.1179/mst.1986.2.6.52010.1179/mst.1986.2.6.520 ↗
21. 10.2464/jilm.37.30010.2464/jilm.37.300 ↗
22. 10.1016/0025-5416(88)90143-710.1016/0025-5416(88)90143-7 ↗
23. ADKINS N. J., , SAUNDERS N., , and TSAKIROPOULOS P.: Mater. Sci. Eng. A, 1988, 98, 212–219.
24. nx I. and LLOYD D. J.: in ‘Casting of near net shape products’ (ed. Y. Sahai et al.) 645-653; 1988 Warrendale PA TMS.
25. 10.1080/0950083890820634810.1080/09500838908206348 ↗
26. 10.1179/mst.1990.6.6.52810.1179/mst.1990.6.6.528 ↗
27. 10.1179/mst.1990.6.8.74910.1179/mst.1990.6.8.749 ↗
28. MISHRA R. S., , JONES H., , and GREENWOOD G. W.: Int. J. Rapid Solidif, 1990, 5, 149–162.
29. SILVA M. P. JONES H. and SELLARS C. M.: in Proc. Conf. ‘PM 90’ Vol. 2 311-314; 1990 London The Institute of Metals.
30. SILVA M. P. WHITEMAN J. A. JONES H. and SELLARS C. M.: in Proc. Conf. ‘PM 90’ Vol. 2 315-319; 1990 London The Institute of Metals.
31. 10.1016/0167-577X(90)90023-F10.1016/0167-577X(90)90023-F ↗
32. STANIEK G., , SHECHTMAN D., , RAMON J., , and BUNK W.: Powder Metall. Int., 1990, 22, (4), 7–10.
33. 10.1016/0921-5093(91)90945-J10.1016/0921-5093(91)90945-J ↗
34. 10.1179/mst.1991.7.4.33410.1179/mst.1991.7.4.334 ↗
35. 10.1179/mst.1991.7.5.41910.1179/mst.1991.7.5.419 ↗
36. 10.1007/BF0266109510.1007/BF02661095 ↗
37. 10.1007/BF0061241910.1007/BF00612419 ↗
38. 10.1016/0921-5093(91)90934-F10.1016/0921-5093(91)90934-F ↗
39. CHUNG M. S., , TU G. C., , and Cs-LEN I. T.: Chin. J. Mater. Sci., 1991, 23, 268–277.
40. 10.1007/BF0074410210.1007/BF00744102 ↗
41. 10.1007/BF0115183210.1007/BF01151832 ↗
42. 10.2464/jilm.43.19310.2464/jilm.43.193 ↗
43. 10.1016/0167-577X(94)90073-610.1016/0167-577X(94)90073-6 ↗
44. COOPER M. J. and SINGER R. F.: in ‘Rapidly quenched metals’ (ed. Steeb S. and Warlimont H. ) 1737-1742; 1985 New York Elsevier.
45. MILLER S. A.: Met. Powder Rep., 1987, 42, 702–703.
46. HOHMANN M. and JONSSON S.: in ‘Special melting and processing technologies’ (ed. Bhat G. K. ) 946-949; 1989 Park Ridge NJ Noyes.
47. PETZOW G. and EFFENBERG G. (eds.): ‘Ternary alloys’ Vol. 4 455-462; 1991 Weinheim VCH.
48. DAVIES R.: in ‘Handbook of powder science and technology’ (ed. Fayed M. E. and Otten L. 31-68; 1984 New York Van Nostrand Reinhold.
49. S. oUNAL ZBILEN A. and SHEPPARD T.: Powder Metall. 1991 34 (1) 53–61.10.1179/pom.1991.34.1.53 ↗
50. 10.1007/BF0112467610.1007/BF01124676 ↗
51. SEE J. B. and JOHNSTON G. W.: Powder Technol. 1987 21 119–133.
52. SEATON C. E. HENEIN H. and GLATZ M.: Powder Metall. 1987 30 (1) 37–47.10.1179/pom.1987.30.1.37 ↗
53. 10.1016/0025-5416(88)90159-010.1016/0025-5416(88)90159-0 ↗
54. MEHROTRA S. P., and KHEDKAR P. Y.: Trans. Indian Inst. Met., 1980, 33, 361–366.
55. RAO K. P. and MEHROTRA S. P.: in ‘Modern developments in powder metallurgy’ Vol. 12 113-129; 1981 Princeton NJ American Powder Metallurgy Institute.
56. 10.1179/mst.1987.3.12.102910.1179/mst.1987.3.12.1029 ↗
57. PANDEY A. B., , SOOD F. K., , and KUMAR M.: Trans. Indian Inst. Met., 1988, 41, (4), 363–370.
58. DUBE R. K., , KORIA S. C., , and SUBRAMANIAN R.: Powder Metall. Int., 1988, 20, (6), 14–17.
59. CJNAL A. NAYLOR M. J. and McSHANE H. B.: Powder Metall. 1990 33 (3) 260–268.10.1179/pom.1990.33.3.260 ↗
60. DUNKLEY J. J. and PALMER J. D.: Powder Metall. 1986 29 287–290.10.1179/pom.1986.29.4.287 ↗
61. LUBANSKA H.: J. Met., 1970, 22, (2), 45–49.
62. COOMBS J. S. DUNSTAN G. R. and HOWELLS R. I. L.: in Proc. Conf. ‘PM 90’ Vol. 2 35-39; 1990 London The Institute of Metals.
63. iTTNAL A.: Int. J. Powder Metall., 1990, 26, 11–21.
64. TIEDJE N. A.‘ SCHRODER PEDERSEN J. KJOLLER B. LARSEN and P. N. HANSEN: in Proc. ‘13/M world congress’ Kyoto July 1993 (ed. Y. Rand° and K. Kosuga) Part 1 13-16; 1993 Tokyo Japan Society of Powder and Powder Metallurgy.
65. 10.1179/mst.1988.4.2.15710.1179/mst.1988.4.2.157 ↗
66. 10.1179/mst.1989.5.6.60910.1179/mst.1989.5.6.609 ↗
67. ADKINS N. J. E., and TSAKIROPOULOS P.: Mater. Sci. Eng. A, 1991, 133, 767–770.
68. ADKINS N. J. E., and TSAKIROPOULOS P.: Int. J. Rapid Solidif., 1991, 6, 87–100.
69. ADKINS N. J. E., and TSAKIROPOULOS P.: Int. J. Rapid Solidif., 1991, 6, 101–114.
70. DAHL W., , GRUHL W., , BURCHARD W. G., , IBE G., , and DUMITRFSCU C.: Z. Metallkd., 1977, 68, 121–127.
71. DAHL W., , GRUHL W., , BURCHARD W. G., , IBE G., , and DUMITRESCU C.: Z. Metallkd., 1977, 68, 188–194.
72. SAHIN E. and JONES H.: in Proc. 3rd Int. Conf. on ‘Rapidly quenched metals’ (ed. Cantor B. Vol. 1 138-146; 1978 London The Metals Society.
73. 10.1007/BF0112001510.1007/BF01120015 ↗
74. JONES H.: in ‘Science and technology of the undercooled melt’ (ed. Sahm P. R. et al.) 156–184; 1986 Dordrecht Boston Lancaster Martinus Nijhoff.
75. LIN P., and DUNLOP G. L.: Mater. Sci. Eng. A, 1991, 134, 1238–1243.