journal article·2009-10

Influence of deformation during T10 treatment on microstructure/hardness/electrical conductivity of Cu–Cr alloy produced in nonprotected atmosphere

E. Hosseini, A. Habibollahzadeh, M. Erfanmanesh, H. Mostajabodave, M. Kazeminezhad

Materials Science and Technology· Volume 25· Issue 10
Publisher page

Abstract

Cu–1·5Cr alloy was successfully produced by a new method, composed of alloying via melting in a non-protected atmosphere followed by rapid cooling in a water cooled mould. The effects of deformation magnitude during T10 treatment on microstructure, electrical conductivity and hardness of alloy were also investigated. The results showed that cold work before age hardening treatment, especially in the range of 20–40% deformation, provides optimum electrical and mechanical properties, i.e. electrical conductivity of 70–85% International Annealed Copper Standard (IACS) and hardness of 160–180 HB. In addition, the cold work promotes a useful anisotropy in electrical and mechanical properties of Cu–1·5Cr alloy after aging treatment. A proposed design for a pilot plant is shown.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Advanced materials and composites · Microstructure and mechanical properties · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Materials Science and EngineeringEngineering Faculty, Semnan University, Semnan, Iran; Department of Materials Science and Engineering, Sharif University of Technology, Azadi Avenue, Tehran, Iran

Department of Materials Science and EngineeringEngineering Faculty, Semnan University, Semnan, Iran

Department of Materials Science and EngineeringSharif University of Technology, Azadi Avenue, Tehran, Iran

References (18)

Show source-provided references
1. Fernee H. · J. Mater. Sc
2. 10.1016/j.msea.2005.03.09510.1016/j.msea.2005.03.095 ↗
3. 10.1007/BF0258615810.1007/BF02586158 ↗
4. 10.1007/s11661-001-0130-x10.1007/s11661-001-0130-x ↗
5. 10.1016/S0043-1648(01)00843-210.1016/S0043-1648(01)00843-2 ↗
6. 10.1016/S1359-6462(02)00350-010.1016/S1359-6462(02)00350-0 ↗
7. 10.1016/S0890-6955(02)00238-910.1016/S0890-6955(02)00238-9 ↗
8. 10.1016/j.msea.2006.02.37910.1016/j.msea.2006.02.379 ↗
9. Batra I. S. · Mater. Sci. Eng. A · 2002 · 356 · 3210.1016/S0921-5093(02)00852-3 ↗
10. 10.1081/AMP-10010430110.1081/AMP-100104301 ↗
11. Wang Y. · Mater. Sci Poland · 2007 · 25 · 199
12. Sun Z., Wange Y., Gue J., Zhu Y., Song X., and Zhu R.: Mater. Sci Eng. A, 2007, A452, 411–416.10.1016/j.msea.2006.10.112 ↗
13. Yamamoto Y., Sasaki G., Yamakawa K., and Ota M.: Hitachi Cable Rev. 2000, 19, 65.
14. Dieter S. ‘Semiconductor material and device characterization’, 2nd Edn, 235-239; 1998, New York, John Wiley and Sons, Inc.
15. Gaskell D. R. ‘Introduction to the thermodynamics of material’, 582; 2003, New York, Taylor and Francis.
16. 10.1016/S1468-6996(01)00029-810.1016/S1468-6996(01)00029-8 ↗
17. 10.1016/j.jmatprotec.2004.08.01310.1016/j.jmatprotec.2004.08.013 ↗
18. Dieter G. E. ‘Mechanical metallurgy’, 3rd edn, 217-252; 1976, New York, McGraw—Hill.