journal article·2012-08

Carburising behaviour of low carbon steel with nanocrystalline surface layer induced by ball milling

F Forghani, A Dolatmoradi, S Kahrobaee, J Vahdati Khaki, M Haddad-Sabzevar

Materials Science and Technology· Volume 28· Issue 8
Publisher page

Abstract

Ball milling, as a surface nanocrystallisation method, was employed to investigate the influence of severe plastic deformation on the carburisation treatment performed on low carbon steel. The results indicated an enhancement in the carburisation efficiency as a result of surface milling. This enhancement was attributed to the formation of a nanocrystalline layer in the surface of the treated samples. It was found that the main reasons for the accelerated kinetics of the carburisation process would be the considerable amounts of non-equilibrium defects and the finer austenite grains in the early and later stages of the treatment respectively, which facilitate the carbon diffusion.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Surface Treatment and Residual Stress · Metal and Thin Film Mechanics · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

School of Metallurgy and Materials Engineering College of Engineering, University of Tehran, Tehran, Iran

Department of Materials Science and Engineering Faculty of Engineering, Ferdowsi University of Mashhad, Mashhad, Iran

References (33)

Show source-provided references
1. Lu K · Mater. Sci. Technol. · 1999 · 15 · 193
2. 10.1016/S1359-6454(02)00310-510.1016/S1359-6454(02)00310-5 ↗
3. 10.1016/S1359-6462(01)00738-210.1016/S1359-6462(01)00738-2 ↗
4. 10.1016/j.matdes.2010.11.02410.1016/j.matdes.2010.11.024 ↗
5. 10.1007/s10853-007-1659-x10.1007/s10853-007-1659-x ↗
6. 10.1179/02670830322500302710.1179/026708303225003027 ↗
7. 10.1016/S1359-6462(01)01258-110.1016/S1359-6462(01)01258-1 ↗
8. 10.1016/S0257-8972(02)00894-010.1016/S0257-8972(02)00894-0 ↗
9. 10.1016/j.matdes.2009.01.01410.1016/j.matdes.2009.01.014 ↗
10. 10.1016/j.stam.2003.10.01510.1016/j.stam.2003.10.015 ↗
11. 10.1016/S0257-8972(03)00254-810.1016/S0257-8972(03)00254-8 ↗
12. 10.1179/174328408X29407110.1179/174328408X294071 ↗
13. 10.1016/j.matdes.2011.10.04210.1016/j.matdes.2011.10.042 ↗
14. 10.1016/0965-9773(93)90016-510.1016/0965-9773(93)90016-5 ↗
15. 10.1016/0921-5093(93)90717-S10.1016/0921-5093(93)90717-S ↗
16. 10.1007/978-3-540-71488-010.1007/978-3-540-71488-0 ↗
17. 10.1016/j.surfcoat.2006.09.10410.1016/j.surfcoat.2006.09.104 ↗
18. 10.1016/0079-6425(89)90001-710.1016/0079-6425(89)90001-7 ↗
19. 10.1126/science.108021610.1126/science.1080216 ↗
20. 10.1016/j.matdes.2011.02.03710.1016/j.matdes.2011.02.037 ↗
21. 10.1179/02670830010150887410.1179/026708300101508874 ↗
22. 10.1016/j.surfcoat.2006.05.01910.1016/j.surfcoat.2006.05.019 ↗
23. 10.1016/j.scriptamat.2008.04.00110.1016/j.scriptamat.2008.04.001 ↗
24. 10.1016/j.actamat.2009.12.02410.1016/j.actamat.2009.12.024 ↗
25. 10.1016/0376-4583(81)90028-510.1016/0376-4583(81)90028-5 ↗
26. 10.31399/asm.tb.mpp.978162708260010.31399/asm.tb.mpp.9781627082600 ↗
27. Klug HP, Alexander LE: ‘X-ray diffraction procedures for polycrystalline and amorphous materials’; 1974, New York, Wiley.
28. 10.1016/S1359-6462(01)00739-410.1016/S1359-6462(01)00739-4 ↗
29. 10.2320/matertrans.43.220510.2320/matertrans.43.2205 ↗
30. Dolatmoradi A, Raygan S, Rad MAsadi, Dehghani K, Khaki JVahdati: ‘Nanomaterials book’, Proc. 49th Conf. Metallurgists, Vancouver, BC, Canada, October 2010, Metallurgical Society of CIM, Paper 15.
31. ‘Standard test method for measurement of metal and oxide coating thickness by microscopical examination of a cross section’, ASTM B487-85, ASTM, West Conshohocken, PA, USA. Current edition approved Feb. 22, 1985. Published May 1985. Originally published as B487–68. Last previous edition B487–79.
32. ‘Standard test method for microhardness and case depth of powder metallurgy (P/M) parts’, ASTM B721-91, ASTM, West Conshohocken, PA, USA. Current edition approved Feb. 22, 1991. Published May 1991.
33. 10.1016/S0257-8972(96)03134-910.1016/S0257-8972(96)03134-9 ↗