Enhanced sintering properties of yttria face coat by addition of B2O3, YF3, Al2O3 and ZrO2
Source abstract
Abstract
Yttria is widely used as a key material in the manufacture of the mould face coat for the investment casting of Ti or titanium aluminide alloys, as it has the required thermal and chemical inertness. Because of the high melting temperature of yttria, moulds manufactured using an yttria face coat need high sintering temperatures to achieve a good surface finish, which increases the production cost of the mould. In this research, small amounts of sintering aids, B2O3, YF3, Al2O3 and ZrO2, were added into a simple yttria face coat and sintered at temperatures from 1000 to 1400°C to investigate the influence on the sintering properties of yttria. These experiments found that the sintering additive B2O3 showed the best performance in enhancing yttria face coat sintering over the test temperatures. Sintering aids such as YF3 only slightly altered the sintering properties of yttria at temperatures around 1000–1200°C, and powders such as YAZ were seen to be more suitable for sintering at temperatures around 1300–1400°C. It may be possible to use these sintering aids for the production of investment casting moulds.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced ceramic materials synthesis · Intermetallics and Advanced Alloy Properties · Aluminum Alloys Composites Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
School of Metallurgy and Materials, University of Birmingham, Birmingham B15 2TT, UK
Rolls-Royce plc, PO box 31, Derby DE24 8BJ, UK
References (23)
Show source-provided references
1. 10.1016/j.jmatprotec.2010.03.00310.1016/j.jmatprotec.2010.03.003 ↗
2. Lassow ES, Johnson PR: US patent no. 4703806, November 1987.
3. Horton R: US patent no. 4947927. August 1990.
4. 10.1016/j.intermet.2008.08.00810.1016/j.intermet.2008.08.008 ↗
5. 10.1016/j.msea.2012.01.09910.1016/j.msea.2012.01.099 ↗
6. 10.1016/S1003-6326(11)61240-510.1016/S1003-6326(11)61240-5 ↗
7. Takayuki I, Masakatsu K: US patent no. 2007161499 (A1), August 2008.
8. 10.1016/0955-2219(94)90060-410.1016/0955-2219(94)90060-4 ↗
9. Joseph RF, Rhodes WH: US patent 4166831, September 1979.
10. 10.1111/j.1151-2916.1967.tb14997.x10.1111/j.1151-2916.1967.tb14997.x ↗
11. Inukai T, Koga K:Proc. Int. Symp. on ‘Factors in densification and sintering of oxide and non-oxide ceramics’(, Sōmiya S, et al.), 677; 1978, Tokyo, Gakujutsu Bunken Fukyu-kai.
12. 10.1016/0025-5408(67)90096-710.1016/0025-5408(67)90096-7 ↗
13. Jones S, Harding R, Holt G: ‘Development of a friability test for the quantitative measurement of primary coat ntergrity of investment casting moulds’, Proc. 12th World Conf. on ‘Investment casting’, Dallas, TX, USA, October 2008, University of Birmingham, UK.
14. 10.1016/0022-3093(93)90246-T10.1016/0022-3093(93)90246-T ↗
15. 10.1016/j.jfluchem.2011.08.01010.1016/j.jfluchem.2011.08.010 ↗
16. 10.1023/A:101150802104710.1023/A:1011508021047 ↗
17. 10.1016/S0925-3467(03)00102-210.1016/S0925-3467(03)00102-2 ↗
18. 10.1006/jssc.1997.756710.1006/jssc.1997.7567 ↗
19. 10.1111/j.1151-2916.1978.tb09220.x10.1111/j.1151-2916.1978.tb09220.x ↗
20. 10.1111/j.1151-2916.1980.tb10772.x10.1111/j.1151-2916.1980.tb10772.x ↗
21. 10.1016/j.jeurceramsoc.2003.09.01010.1016/j.jeurceramsoc.2003.09.010 ↗
22. 10.1016/j.cis.2007.04.00910.1016/j.cis.2007.04.009 ↗
23. 10.1007/s10853-009-4128-x10.1007/s10853-009-4128-x ↗