journal article·2016-12

Evolution of microstructure and crystallographic texture during recrystallisation of high-strength sheet steel

S. Chatterjee, S. Mukherjee, S. Kundu

Materials Science and Technology· Volume 32· Issue 18
Publisher page

Abstract

Ultra-low carbon steels possess an attractive combination of mechanical properties namely drawability and strength that is suitable for automotive applications. A high-strength variant of the material containing large amounts of manganese and phosphorous has been produced in the laboratory. The main objective of the present work was to study the microstructural evolution after recrystallisation, below and above the critical phase transformation temperatures of the steel. Crystallographic texture of ferrite was found to intensify with increasing the annealing temperature; surprisingly even beyond the upper transformation temperature. The texture measurement data obtained with the electron backscatter diffraction and X-ray diffraction matched very well with each other. The steel recorded an impressive strength–drawability balance mainly due to solid solution strengthening and favourable γ-fibre texture.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Microstructure and mechanical properties · Magnetic Properties and Applications

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Research & Development, Tata Steel Limited, P.O. Burma Mines, Jamshedpur 831007, Jharkhand, India

References (27)

Show source-provided references
1. 10.1179/imtr.1984.29.1.2510.1179/imtr.1984.29.1.25 ↗
2. 10.1016/S0921-5093(97)00455-310.1016/S0921-5093(97)00455-3 ↗
3. De Cooman B. C., and De Vyt A. ‘International forum for the properties and application of IF steels – IF STEELS 2003’, Tokyo, 2003, 249.
4. 10.1016/0956-716X(93)90065-Z10.1016/0956-716X(93)90065-Z ↗
5. 10.1016/S1359-6462(00)00638-210.1016/S1359-6462(00)00638-2 ↗
6. 10.1002/srin.20040594410.1002/srin.200405944 ↗
7. 10.1016/0001-6160(89)90101-610.1016/0001-6160(89)90101-6 ↗
8. 10.1016/S1359-6462(02)00282-810.1016/S1359-6462(02)00282-8 ↗
9. 10.1016/S1044-5803(00)00070-X10.1016/S1044-5803(00)00070-X ↗
10. 10.1016/j.scriptamat.2006.03.04310.1016/j.scriptamat.2006.03.043 ↗
11. 10.1016/j.scriptamat.2006.12.04410.1016/j.scriptamat.2006.12.044 ↗
12. 10.1179/02670830010150690210.1179/026708300101506902 ↗
13. 10.4028/www.scientific.net/MSF.702-703.79810.4028/www.scientific.net/MSF.702-703.798 ↗
14. 10.1016/S1006-706X(13)60115-610.1016/S1006-706X(13)60115-6 ↗
15. Chen Y.-L. · Cailiao Rechuli Xuebao/Trans. Mater. Heat Treat. · 2012 · 33 · 117
16. Yan Q. · Cailiao Rechuli Xuebao/Trans. Mater. Heat Treat. · 2011 · 32 · 71
17. Thermo-Calc software, version R: ‘Foundation of computational thermodynamics’, 1993–2006, Stockholm, Sweden.
18. Forouraghi K. ‘Ultrasonic measurement of drawability (r-values) of low carbon steel sheets’, PhD thesis, Retrospective theses and dissertations, Paper 10903, 1995, 19.
19. 10.1016/S1359-6462(97)00185-110.1016/S1359-6462(97)00185-1 ↗
20. Bunge H. J. · 1982
21. 10.2355/isijinternational.34.92710.2355/isijinternational.34.927 ↗
22. 10.1179/imr.1994.39.4.12910.1179/imr.1994.39.4.129 ↗
23. 10.2355/isijinternational.41.88310.2355/isijinternational.41.883 ↗
24. 10.1007/s11661-012-1096-610.1007/s11661-012-1096-6 ↗
25. 10.5962/bhl.title.3589510.5962/bhl.title.35895 ↗
26. Van Houtte P. ‘The MTM-FHM software system’, Version 2, Department of Metallurgy and Materials Engineering, Katholieke Universiteit Leuven, Belgium.
27. 10.2320/matertrans.MA20070410.2320/matertrans.MA200704 ↗