Modelling generation mechanism of defects during permanent mould centrifugal casting process of TiAl alloy exhaust valve
Source abstract
Abstract
In this paper, the TiAl liquid filling process during vertical centrifugal casting into a permanent mould has been described analytically. A model has been established to simulate the forward filling and backward filling process, and two parameters were used to provide a quantitative description of the defect generation that is associated with the forward filling of the mould cavity. One of the parameters used was the forward filling cross-sectional area, and the other was the inclined angle of the free surface of forward filling flow. The cross-sectional area decreases, and the inclined angle increases when the rotational speed increases, the tendency of which becomes more obvious near the mould cavity entrance. The residual volume of the mould cavity after the forward filling is related to the volume of trapped pores. The filling process has also been investigated using numerical simulation. Based on the filling and solidification characteristic of a TiAl valve, the off-centre porosity distribution is also discussed.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Intermetallics and Advanced Alloy Properties · Advanced materials and composites · Advanced ceramic materials synthesis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
School of Materials Science and Engineering Harbin Institute of Technology, Harbin 150001, China
References (17)
Show source-provided references
1. 10.1179/mst.1992.8.4.36710.1179/mst.1992.8.4.367 ↗
2. 10.1007/BF0322032210.1007/BF03220322 ↗
3. 10.1007/BF0322026710.1007/BF03220267 ↗
4. 10.1007/BF0322225410.1007/BF03222254 ↗
5. 10.1016/S0966-9795(01)00064-410.1016/S0966-9795(01)00064-4 ↗
6. 10.1007/BF0240380610.1007/BF02403806 ↗
7. Jones P. E., Porter W. J., and Eylon D. ‘Development of a low cost permanent mold casting process for TiAl automotive valves’, in ‘Gamma titanium aluminides’, (ed. Kim Y.W. et al.), 53–62; 1995, Warrendale, PA, TMS.
8. Austin C. M., and Kelly T. J. ‘Progress in implementation of cast gamma titanium aluminde’, in ‘Gamma titanium aluminides’, (ed. Kim Y.W. et al.), 21–32; 1995, Warrendale, PA, TMS.
9. 10.1016/S0966-9795(98)00036-310.1016/S0966-9795(98)00036-3 ↗
10. 10.1016/S0966-9795(98)00060-010.1016/S0966-9795(98)00060-0 ↗
11. 10.1016/S0921-5093(01)01513-110.1016/S0921-5093(01)01513-1 ↗
12. 10.1016/j.intermet.2004.12.00410.1016/j.intermet.2004.12.004 ↗
13. 10.1016/j.intermet.2007.08.00710.1016/j.intermet.2007.08.007 ↗
14. Wu S. P. · Mater. Sci. Eng. A · 2006 · 426 · 24010.1016/j.msea.2006.04.014 ↗
15. 10.1179/02670830110150941210.1179/026708301101509412 ↗
16. 10.1179/02670830322500594410.1179/026708303225005944 ↗
17. 10.1007/s11663-004-0019-310.1007/s11663-004-0019-3 ↗