journal article·2004-12

Effect of long term elevated temperature service on the properties of type P–22 steel

S. Perets, A. Arbel, S. Ariely, A. Venkert, R.Z. Shneck

Materials Science and Technology· Volume 20· Issue 12
Publisher page

Abstract

Extensive service at 540°C led to changes in the composition, morphology, size, and distribution of the original carbides that were present in the pre-service steel. This service did not seem to introduce weakening voids along grain boundaries. At low creep stress levels the stress versus Larson–Miller parameter (LMP) curve of the postservice steel indicates better performance than the lower bound of the pre-service steel. The opposite performance was found at high creep stress levels. The service led to only a slight reduction in fracture toughness of the steel. Exposure to post-service accelerated creep tests led to further gradual reduction in fracture toughness. The reductions in fracture toughness were proportional to the creep strain and duration. The formation of spherical carbides during the accelerated creep tests promoted void formation during the fracture process and thus contributed to the observed additional reduction in fracture toughness.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: High Temperature Alloys and Creep · Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (17)

Show source-provided references
1. 10.1016/0036-9748(79)90264-310.1016/0036-9748(79)90264-3 ↗
2. 10.1007/BF0055132110.1007/BF00551321 ↗
3. ROBINSON E. L. · Trans. ASME · 1983 · 160 · 253
4. LIBERMAN Y. · Metalloved Term Obrab. Met · 1962 · 4 · 6
5. VOORHESS H. R. · Notch sensitivity of aircraft structural and engine alloys' · 1959
6. BAKER R. G. · J. Iron Steel. Inst · 1959 · 192 · 257
7. G. V. SMITH: `ASTM Data Series DS 6S2', 1–139; 1971, Philadelphia, PA, ASTM.
8. K. YAGI and F. ABE: 'Creep and fracture of engineering materials and structures', (ed. J. C. Earthman et al.), 427–436; 1977, Warrendale, PA, TMS.
9. 10.1007/BF0265681310.1007/BF02656813 ↗
10. JAYAN V. · Mater. Set Technol · 1999 · 15 · 130810.1179/026708399101505266 ↗
11. 10.1179/02670830322500788910.1179/026708303225007889 ↗
12. 'Standard test method for J · Annual Book of ASTM Standards · 1997 · 01 · 646
13. 10.1016/0013-7944(76)90011-410.1016/0013-7944(76)90011-4 ↗
14. J. D. LANDES and J. A. BEGLEY: in 'Development in fracture mechanics test methods standardization, (ed. W. F. Brown, Jr. and J. G. Kaufman), STP 632', 57–81; 1977, Philadelphia, PA, ASTM.10.1520/STP28700S ↗
15. G. SUCCOP, R. T. BUBSEY, M. H. JONES and W. F. BROWN, JR: in 'Development in fracture mechanics test methods standardiza-tion, (ed. W. F. Brown Jr and J. G. Kaufman), STP 632' 153–158; 1977, Philadelphia, PA, ASTM.
16. 10.1007/BF0266063810.1007/BF02660638 ↗
17. KACHANOV L. M. · Otd Techn. Nauk · 1958 · 8 · 26