journal article·2014-08

Laser and GTAW torch processing of Fe–Cr–B coatings on steel

A. N. Md Idriss, S. Mridha, T. N. Baker

Materials Science and Technology· Volume 30· Issue 10
Publisher page

Abstract

A comparison of a coating of Fe–Cr–B alloy powder processed on a plain carbon steel by surface melting using either laser or gas tungsten arc welding (GTAW) torch was made. The alloy powder was injected in laser melted surface, while the preplaced powder was melted using the GTAW technique. The topography of the GTAW tracks showed a relatively smooth surface, but the laser track surface was very rough. Because of high energy input, the GTAW method produced very wide and deep tracks with a high dilution compared to those of the laser tracks. Pores and fine cracks were seen in laser tracks; the cracks were elongated across the track width, and some of them propagated down to the melt depth. The GTAW track produced at a low energy was free from any cracking, but a centreline crack was present when processed at a high energy input.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Laser Material Processing Techniques · High Entropy Alloys Studies · Additive Manufacturing Materials and Processes

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Advanced Materials and Surface Engineering Research Unit, Department of Manufacturing and Materials Engineering, International Islamic University of Malaysia, PO Box 10, Kuala Lumpur 50728, Malaysia

Department of Mechanical and Aerospace Engineering, University of Strathclyde, James Weir Building, Glasgow G1 1XJ, UK

References (28)

Show source-provided references
1. 10.1533/978184569945110.1533/9781845699451 ↗
2. Toyserkani AKE and Corbin S: ‘Laser cladding’; 2005, Boca Raton, FL, CRC Press LLC.10.1201/9781420039177 ↗
3. 10.1016/S0257-8972(99)00141-310.1016/S0257-8972(99)00141-3 ↗
4. 10.1016/S0257-8972(03)00811-910.1016/S0257-8972(03)00811-9 ↗
5. 10.1016/S0924-0136(01)00609-410.1016/S0924-0136(01)00609-4 ↗
6. 10.1016/j.apsusc.2005.02.08810.1016/j.apsusc.2005.02.088 ↗
7. 10.1016/j.jallcom.2006.03.08310.1016/j.jallcom.2006.03.083 ↗
8. 10.1016/j.jmatprotec.2005.02.24710.1016/j.jmatprotec.2005.02.247 ↗
9. Mridha S · IJMME · 2012 · 7 · 48
10. 10.1016/j.surfcoat.2006.01.04010.1016/j.surfcoat.2006.01.040 ↗
11. 10.1081/AMP-12002249710.1081/AMP-120022497 ↗
12. 10.1023/B:JMSC.0000007750.16970.4e10.1023/B:JMSC.0000007750.16970.4e ↗
13. Chokethawai K: ‘Microstructural evolution in Fe–Cr–B based alloy powder and thermally sprayed coatings and their wear performance’, PhD thesis, University of Nottingham, Nottingham, UK, 2010.
14. Branagan DJ · Adv. Mater. Process. · 2011 · 169 · 33
15. http://nanosteelco.com/
16. 10.1016/j.jallcom.2009.02.03510.1016/j.jallcom.2009.02.035 ↗
17. 10.1016/j.surfcoat.2010.10.02910.1016/j.surfcoat.2010.10.029 ↗
18. Schneider M: ‘Laser cladding with powder, effect of some machining parameters on clad properties’, PhD thesis, University of Twente, Enschede, The Netherlands, 1998.
19. 10.1361/10599639977035029610.1361/105996399770350296 ↗
20. 10.4028/www.scientific.net/AMR.445.65510.4028/www.scientific.net/AMR.445.655 ↗
21. Easterling KE: ‘Introduction to physical metallurgy of welding’; 1992, London, Butterworth-Heinemann’.
22. 10.1016/j.jmatprotec.2006.03.11010.1016/j.jmatprotec.2006.03.110 ↗
23. 10.4028/www.scientific.net/AMR.264-265.142710.4028/www.scientific.net/AMR.264-265.1427 ↗
24. 10.1179/02670849910151653310.1179/026708499101516533 ↗
25. 10.1016/j.surfcoat.2004.03.05810.1016/j.surfcoat.2004.03.058 ↗
26. 10.1179/mst.1994.10.6.53610.1179/mst.1994.10.6.536 ↗
27. 10.1007/978-3-642-82638-2_7810.1007/978-3-642-82638-2_78 ↗
28. A. N. Md Idriss, S. Mridha and T. N. Baker: ‘Laser and GTAW torch processing of Fe–Cr–B coatings on steel. Part II – microstructure and hardness’, Mater. Sci. Technol. DOI 10.1179/1743284714Y.0000000547.