Forming and fracture limits of aluminium alloy
Source abstract
Abstract
Forming and fracture limits of an AA 3104-H19 aluminium alloy sheet were studied by hydraulic bulging and Marciniak type deep drawing and tensile tests. The alloy appeared to be highly anisotropic, exhibiting distinctly different fracture patterns in the rolling and transverse directions. The preferred fracture direction was transverse to the rolling direction. In the tensile test, samples loaded in the rolling direction failed transverse to the rolling direction, but in the transverse direction, the fracture was inclined at ∼55° to the tensile axis. In some cases, two such competing fractures in the characteristic directions could be observed. Scanning electron microscopy studies revealed a typical ductile fracture pattern. The fracture occurred by shearing in the through thickness direction, and typical alternating shear lips in a direction inclined at ∼45° to the through thickness direction could be observed. Forming limit diagrams for both rolling and transverse directions were determined from the experiments. The measured limit strains in uniaxial tension were predicted well by the modified Rice–Tracey theory, but in equibiaxial tension, the theory overestimated the fracture limit strains.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Metal Forming Simulation Techniques · Metallurgy and Material Forming · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Materials Science and Engineering, Aalto University School of Science and Technology, PO Box 16200, Espoo, FI-00076 Aalto, Finland
References (25)
Show source-provided references
1. Keeler SP · Trans. ASM · 1963 · 56 · 25
2. Goodwin GM: ‘Application of strain analysis to sheet metal forming problems in the press shop’, SAE paper no. 680093, SAE International, Warrendale, PA, USA, 1968.10.4271/680093 ↗
3. Gensamer M · Trans. ASM · 1946 · 36 · 30
4. 10.1088/0022-3727/7/7/30710.1088/0022-3727/7/7/307 ↗
5. Lankford WT · Trans. AIME · 1947 · 171 · 574
6. 10.1016/S0749-6419(01)00033-X10.1016/S0749-6419(01)00033-X ↗
7. 10.1016/j.ijplas.2006.07.00510.1016/j.ijplas.2006.07.005 ↗
8. 10.1016/0022-5096(57)90001-710.1016/0022-5096(57)90001-7 ↗
9. 10.1016/0022-5096(57)90040-610.1016/0022-5096(57)90040-6 ↗
10. 10.1115/1.344349410.1115/1.3443494 ↗
11. 10.1016/0022-5096(52)90003-310.1016/0022-5096(52)90003-3 ↗
12. 10.1016/S0022-5096(01)00031-X10.1016/S0022-5096(01)00031-X ↗
13. Korhonen AS · Acta Polytech. Scand. · 1980 · 144 · 1
14. Hollomon JH · Trans. AIME · 1945 · 162 · 268
15. Voce E · J. Inst. Met. · 1948 · 5 · 537
16. 10.1016/0020-7403(73)90068-410.1016/0020-7403(73)90068-4 ↗
17. 10.1007/BF0281530510.1007/BF02815305 ↗
18. 10.1016/0022-5096(69)90033-710.1016/0022-5096(69)90033-7 ↗
19. 10.1016/j.msea.2007.11.00610.1016/j.msea.2007.11.006 ↗
20. 10.1016/S0020-7683(01)00246-310.1016/S0020-7683(01)00246-3 ↗
21. 10.1016/S0020-7683(02)00162-210.1016/S0020-7683(02)00162-2 ↗
22. Takuda H · Steel Grips · 2004 · 2 · 439
23. 10.1007/s12289-009-0489-610.1007/s12289-009-0489-6 ↗
24. ‘Metallic materials – sheet and strip – determination of forming-limit curves – Part 2: determination of forming-limit curves in the laboratory’, ISO 12004-2:2008, ISO, Geneva, Switzerland, 2008.
25. Yoon JW, Dick RE, Barlat F, Hong SE: ‘On the use of stress-based forming limit curve for forming and fracture’, Proc. 9th Int. Conf. on ‘Technology of plasticity’, Gyeongju, Korea, September 2008, The Japan Society for Technology of Plasticity, 708–722.