Microstructural, mechanical and electrochemical characterisation of biomaterial ASTM F745 cast by vacuum
Source abstract
Abstract
Countergravity low pressure casting (CLA) was performed to enhance the properties of ASTM F745 stainless steel (SS), which is usually used as biomaterial. The macro- and microstructures were compared with those obtained by the conventional process of investment casting (IC). The SS cast by CLA (SSCLA) exhibited a smaller size of solidification cell and finer dendritic microstructure. The average of its dendritic primary spacing was 110·4 μm, while for the same steel cast by IC (SSIC), it was 186·7 μm. The density of non-metallic inclusions δI in the SSCLA was 717 I mm−2, being the majority of them smaller than 1·5 μm. In the case of SSIC, δI was 852 I mm−2, with a size distribution of up to 8 μm. The SSCLA showed a higher breakdown potential than the SSIC, the values being 0·300 and 0·210 V(saturated calomel electrode) respectively, which means a higher resistance to suffer localised corrosion. Finely, the CLA process also allowed obtaining better mechanical properties.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Titanium Alloys Microstructure and Properties · Surface Treatment and Residual Stress · Additive Manufacturing Materials and Processes
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Laboratorio de Entrenamiento Multidisciplinario para la Investigación Tecnológica (LEMIT-CICPBA), Av. 52 s/n e/121 y 122, La Plata B1900AYB, Argentina
Centro de Investigación y Desarrollo en Tecnología de Pinturas (CIDEPINT-CICPBA-CONICET), Av. 52 s/n e/121 y 122, La Plata B1900AYB, Argentina
Facultad de Ingeniería, UNLP, Av. 1 esq. 47, La Plata B1900AYB, Argentina
References (17)
Show source-provided references
1. ‘Specification for 18chromium–12·5nickel–2·5molybdenum stainless steel manufacturing and related processes’ ASTM F745-07, Section 13, 302–304, ASTM International, Baltimore, MD, USA, 2007.
2. Brunski JB:in ‘Biomaterials science – an introduction to materials in medicine’(, Ratner B D, et al.), 2nd edn, 137–153; 2004, San Diego, CA, Elsevier Academic Press.
3. 10.1016/S0142-1123(00)00052-910.1016/S0142-1123(00)00052-9 ↗
4. 10.1016/j.engfailanal.2004.05.00410.1016/j.engfailanal.2004.05.004 ↗
5. 10.1007/BF0045657310.1007/BF00456573 ↗
6. 10.1007/BF0271533110.1007/BF02715331 ↗
7. Demian C · J. Optoelectron. Biomed. Mater. · 2009 · 1 · 172
8. ASM International: ‘Metals handbook’, 9th edn, Vol. 15, ‘Casting’, 696–700; 1988, Materials Park, OH, ASM International.
9. ASM International: ‘Metals handbook’, 9th edn, Vol. 9, ‘Metallography and microstructures’, 141; 1988, Materials Park, OH, ASM International.
10. Kurz W, Fisher DJ: ‘Fundamentals of solidification’, 3rd edn, 63–92; 1992, Aedermannsdorf, Trans Tech Publications.
11. Flemings MC: ‘Solidification processing’, ‘Materials science and engineering series’, 146–154; 1974, New York, McGraw-Hill, Inc.
12. 10.1002/1522-2586(200007)12:1<92::AID-JMRI11>3.0.CO;2-710.1002/1522-2586(200007)12:1<92::AID-JMRI11>3.0.CO;2-7 ↗
13. 10.3171/jns.2002.97.6.147210.3171/jns.2002.97.6.1472 ↗
14. 10.1016/j.corsci.2006.08.01710.1016/j.corsci.2006.08.017 ↗
15. Manivasagam G · Corros. Sci. · 2010 · 2 · 40
16. 10.1007/BF0270645010.1007/BF02706450 ↗
17. 10.1016/j.surfcoat.2006.02.00810.1016/j.surfcoat.2006.02.008 ↗