Forging behaviour and properties of metal matrix composites based on mechanically alloyed AI-Mg-Li alloy
Source abstract
Abstract
A range of Al-Mg-Li-C MMCs (25 vol.-% of 3 μm SiC particles) were produced by mechanical alloying and powder processing at Aerospace Metal composites, Farnborough. Upset forging trials were conducted at 350 and 550°C and 0.01 and 0.1 S -l . No SiC particle cracking or wedge cracking at grain boundary triple points was observed. Forging at 550°C caused some edge cracking and a coarser grain structure. Large billets of varying composition were forged to ∼15 mm thick plate at 350°C and 0.0l S- l or 550°C and 0.l S -l . Monotonic testing showed the MMCs to exhibit high stiffnesses at moderate strength levels but rather low ductility and fracture toughness. Significant strengthening was found to accrue from dispersion hardening (C content) and solid solution strengthening (Mg and Li solutes). A link was found between lower proof stress and coarser grain structure after forging at 550°C. Fracture toughness K 1C was found to decrease with increasing yield strength which was attributed to higher strain concentrations in the smaller crack tip plastic zone.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (29)
Show source-provided references
1. GILMAN P. S.: Proc. 2nd Conf. on Aluminium—lithium alloys’ (ed. Sanders T. H. and Starke E. A.) 485; 1984 Warrendale PA TMS-AIME.
2. DONACHIE S. J. and GILMAN R S.: Proc. 2nd Conf. on ‘Aluminium—lithium alloys’ (ed. Sanders T. H. and Starke E. A.) 507; 1984 Warrendale PA TMS-AIME.
3. VINE W. J.: Report DRA/SMC/CR962244 SMC DERA Farnborough 1996.
4. 10.1007/BF0264349010.1007/BF02643490 ↗
5. PILLING J.: Scr. Metall. Mater., 1989, 23, 1375.
6. 10.1007/BF0264948110.1007/BF02649481 ↗
7. FLITCROFT S. M. and McDARMAID D. S.: Report 92052 SMC DERA Farnborough 1992.
8. 10.1016/0036-9748(84)90374-010.1016/0036-9748(84)90374-0 ↗
9. 10.1080/17432847.1995.1194555610.1080/17432847.1995.11945556 ↗
10. 10.1007/BF0264601510.1007/BF02646015 ↗
11. HUTCHINSON W. G., and PALMIERE E. J.: Mater. Trans., JIM, 1996, 37, 330.
12. OROWAN E.: Proc. Symp. on ‘Internal stresses in metals and alloys’ 451; 1984 London The Institute of Materials.
13. SANDERS R. E.: Proc. Int. Conf. on ‘Aluminium alloys’ Charlottesville VA USA June 1986 Aluminum Association.
14. HATCH J. E.: in ‘Aluminium: properties and physical metallurgy’ (ed. Hatch J. E.) 29; 1984 Metals Park OH American Society for Metals.
15. 10.1007/BF0264376610.1007/BF02643766 ↗
16. 10.1179/03063458279042752310.1179/030634582790427523 ↗
17. 10.1007/BF0267041710.1007/BF02670417 ↗
18. 10.1016/0001-6160(77)90171-710.1016/0001-6160(77)90171-7 ↗
19. 10.1080/0141861830824312610.1080/01418618308243126 ↗
20. 10.1179/msc.1980.14.5.19310.1179/msc.1980.14.5.193 ↗
21. 10.1007/BF0335096110.1007/BF03350961 ↗
22. 10.1007/BF0335095310.1007/BF03350953 ↗
23. 10.1016/0956-7151(90)90155-A10.1016/0956-7151(90)90155-A ↗
24. STYLES C. M.: ‘Fracture and fatigue behaviour of a particulate reinforced aluminium based composite’, PhD thesis, University of Southampton, 1993.
25. 10.1179/mst.1994.10.6.47510.1179/mst.1994.10.6.475 ↗
26. 10.1179/mst.1998.14.9-10.105310.1179/mst.1998.14.9-10.1053 ↗
27. CHEN C. Q., and KNOTT J. F.: Mater. Sci., 1981, 15, 357.
28. 10.1007/BF0265224210.1007/BF02652242 ↗
29. 10.1007/BF0264708310.1007/BF02647083 ↗