Effects of Mg doping on sol–gel derived nanocrystalline hydroxyapatite thin films
Source abstract
Abstract
Both pure and Mg doped thin films were fabricated by sol–gel dip coating. The films were sintered either at 800 or 1000°C. The average grain size of the films was significantly affected by Mg substitution in the hydroxyapatite (HA) structure and change in the sintering temperature. The grains were considerably larger in the films sintered at higher temperatures. In addition, Mg doped films contained significantly larger grains compared to undoped HA films. Mg doping also caused rodlike grains at 800°C, and led to whitlockite ( β-TCP) formation at 1000°C. The ratio of the existing phases was estimated as β-TCP/HA=27 : 73. All the films had rough surfaces with high porosity. It was also observed that undoped films had higher surface roughness than Mg doped ones.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Bone Tissue Engineering Materials · Dental materials and restorations · Dental Implant Techniques and Outcomes
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Materials Science and EngineeringGebze Institute of Technology, Kocaeli, Turkey
Department of PhysicsGebze Institute of Technology, Kocaeli, Turkey
Department of Materials Science and EngineeringGebze Institute of Technology, Kocaeli, Turkey;, Email: aoral@gyte.edu.tr
References (32)
Show source-provided references
1. Porter A. E., Patel N., and Best S.: in: ‘Encyclopedia of biomaterials and biomedical engineering’, 1-13; 2006, New York, Dekker.
2. LeGeros R. Z.: in ‘Hydroxyapatite and related materials’, (ed. P.W. Brown et al), 3-29; 1994, Florida, CRC Press.
3. 10.1016/S0142-9612(03)00479-410.1016/S0142-9612(03)00479-4 ↗
4. Hench L. L.: in ‘Biomaterials science: an introduction to materials in medicine’, (ed.Ratner B. et al), 73-84; 1996, San Diego, CA, Academic Press.
5. Billotte W. C.: in ‘Biomedical engineering fundamentals’, (ed. Bronzino J. D. et al),8; 2006, Boca Raton, FL, CRC Press.
6. Korkusuz P., and Korkusuz F.: in ‘Biomaterials in orthopedics’, (ed.Yaszemski M. J. et al), 1-6; 2004, New York, Dekker.10.1201/b14227-2 ↗
7. 10.1016/S0142-9612(00)00332-X10.1016/S0142-9612(00)00332-X ↗
8. 10.1016/j.progsolidstchem.2004.07.00110.1016/j.progsolidstchem.2004.07.001 ↗
9. 10.1016/S0169-4332(02)01413-710.1016/S0169-4332(02)01413-7 ↗
10. 10.1016/S0040-6090(98)00531-810.1016/S0040-6090(98)00531-8 ↗
11. 10.1016/S0142-9612(02)00573-210.1016/S0142-9612(02)00573-2 ↗
12. 10.1016/S0142-9612(00)00060-010.1016/S0142-9612(00)00060-0 ↗
13. 10.1016/S0168-583X(01)00585-710.1016/S0168-583X(01)00585-7 ↗
14. 10.1016/j.apsusc.2005.01.13410.1016/j.apsusc.2005.01.134 ↗
15. 10.1016/j.nimb.2006.03.12610.1016/j.nimb.2006.03.126 ↗
16. 10.1016/j.tsf.2004.06.13810.1016/j.tsf.2004.06.138 ↗
17. 10.1016/S0022-2860(01)00716-510.1016/S0022-2860(01)00716-5 ↗
18. 10.1016/S0142-9612(97)00177-410.1016/S0142-9612(97)00177-4 ↗
19. 10.1016/S0142-9612(98)90138-710.1016/S0142-9612(98)90138-7 ↗
20. 10.1023/A:100894822888010.1023/A:1008948228880 ↗
21. 10.1016/j.solidstatesciences.2006.01.00810.1016/j.solidstatesciences.2006.01.008 ↗
22. 10.1016/S0142-9612(01)00219-810.1016/S0142-9612(01)00219-8 ↗
23. Daculsi G., and LeGeros R.: in ‘Encyclopedia of biomaterials and biomedical engineering’, (ed.Bowlin G. L. et al), 1-9; 2006, New York, Dekker.
24. 10.1016/j.jssc.2005.08.00310.1016/j.jssc.2005.08.003 ↗
25. 10.1016/S0142-9612(02)00523-910.1016/S0142-9612(02)00523-9 ↗
26. Qi G., Zhang S., Khor K. A., Liu C., Zeng X., Weng W., and Qian M.: Thin Solid Films, 2007, to be published.
27. 10.1016/j.apsusc.2004.03.20310.1016/j.apsusc.2004.03.203 ↗
28. Liith H., Thust M., Steffen A., Kordos P., and Schöning M. J.: Mater. Set Eng. B, 2000, B69-70,104–108.10.1016/S0921-5107(99)00275-5 ↗
29. 10.1016/S0928-4931(01)00219-310.1016/S0928-4931(01)00219-3 ↗
30. 10.1016/j.mseb.2004.04.01110.1016/j.mseb.2004.04.011 ↗
31. 10.1016/S0167-577X(02)01112-610.1016/S0167-577X(02)01112-6 ↗
32. 10.1016/j.biomaterials.2003.12.00810.1016/j.biomaterials.2003.12.008 ↗