journal article·1988-10

Ranges of application of free-cutting steels and recommended tool materials

M. L. H. Wise, R. Milovic

Materials Science and Technology· Volume 4· Issue 10
Publisher page

Abstract

Four low carbonfree-cutting steels (0·11% carbon resulphurised, 0·11% carbon leaded–resulphurised, 0·08% carbon resulphurised, and 0·15% carbon leaded) were turned, dry, with a series of six types of cutting tool in which rake angle, tool material, and coating were varied (5° rake, high speed steel, TiN coated and uncoated; 15° rake, high speed steel, TiN coated and uncoated; 5° rake, cemented carbide, TiN coated and uncoated) in order to determine the optimum tool–workpiece combination for three cutting speed ranges: a low speed range in which the built-up edge (BUE) was forming or about to form; a speed range covering the BUE regime; and a higher speed range in which the BUE became a built-up layer (BUL). Tool–workpiece interaction was assessed by measurement of cutting forces, chip form, surface finish, tool temperature, and wear. It is suggested by the results that the best combination in the low speed range is that of leaded–resulphurised steel and uncoated high speed steel. In the BUE range, the combination of leaded steels and uncoated tools should be avoided; at higher speeds, coated tools are preferred, with non-resulphurised leaded steel giving the lowest tool temperatures and highest cutting speeds before ultimate failure. These recommendations should be treated with caution and used only as guidelines.MST/867
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Advanced machining processes and optimization · Metal Alloys Wear and Properties · Advanced Surface Polishing Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (22)

Show source-provided references
1. E. M. TRENT: ‘Metal cutting’, 2 edn; 1984, London, Butterworths.10.1016/B978-0-408-05031-9.50009-0 ↗
2. VACCARI J. A. · Am. Mach. Autorn. Manuf · 1986 · 130 · 115
3. 10.1007/BF0283392910.1007/BF02833929 ↗
4. SHAW M. C. · Trans. ASME · 1961 · 83 · 16310.1115/1.3680504 ↗
5. SHAW M. C. · Trans. ASME · 1961 · 83 · 175
6. SHAW M. C. · Trans. ASME · 1961 · 83 · 18110.1115/1.3680511 ↗
7. MARSTON G. J. · J. Iron Steel Inst., · 1970 · 208 · 568
8. B. W. DINES: PhD thesis, University of Birmingham, 1975.
9. 10.1038/253187a010.1038/253187a0 ↗
10. 10.1016/0025-5416(77)90115-X10.1016/0025-5416(77)90115-X ↗
11. 10.1179/03071697680339183610.1179/030716976803391836 ↗
12. B. MILLS and R. H. REDFORD: ‘Machinability of engineering materials'; 1983, London/New York, Applied Science Publishers.10.1007/978-94-009-6631-4 ↗
13. R. MILOVIC: PhD thesis, University of Birmingham, 1983.
14. 10.1179/mst.1986.2.1.5910.1179/mst.1986.2.1.59 ↗
15. 10.1179/mst.1987.3.2.15510.1179/mst.1987.3.2.155 ↗
16. 10.1007/BF0283390910.1007/BF02833909 ↗
17. V · A. TIPNIS and R. A. JOSEPH: J. Eng. Ind., · 1971 · 571
18. WILLIAMS J. E. · MetallUrgia · 1970 · 81 · 3
19. WRIGHT P. K. · J. Iron Steel Inst., · 1973 · 211 · 364
20. 10.1016/S0007-8506(07)63365-410.1016/S0007-8506(07)63365-4 ↗
21. 10.1179/03071697480328783410.1179/030716974803287834 ↗
22. 10.1179/03071698180327552310.1179/030716981803275523 ↗