journal article·2010-12

Microstructure and wear properties of novel sintered cold work steel and related particle reinforced composite materials

S. Weber, J. R. Li, W. Theisen

Materials Science and Technology· Volume 26· Issue 12
Publisher page

Abstract

In the field of wear resistant materials it is known, that for certain applications steel based composites produced by powder metallurgy are beneficial due to a higher wear resistance compared to conventional cast materials. Early developments of these high wear resistant MMC were dependent on hot isostatic pressing but latest experimental findings nowadays also allow for a production by liquid phase sintering. Several materials systems have already been investigated which, however, lack of a sufficient hardness in the as sintered state. Especially for wear resistant coatings it would be beneficial to avoid a separate hardening of a coated component. The low hardness in the as sintered state is related to the transformation kinetics of the metallic matrix of the coating materials, typically leading to a comparatively soft pearlitic microstructure, if the cooling rate is too low. The use of a nickel alloyed PM cold work steel as matrix material avoids this restriction, as the formation of pearlite and bainite is delayed significantly, improving the hardenability of the steel. Adding coarse hard particles of chromium carbide (Cr3C2), aluminium zirconium oxide (AlZrO) or titanium carbide (TiC) to the steel powder, composite materials with a high abrasive wear resistance can be obtained by liquid phase sintering. The development of these materials, supported by thermodynamic calculations, is presented here together with results of the microstructural investigation and wear tests.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Metal Alloys Wear and Properties · Powder Metallurgy Techniques and Materials · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Helmholtz-Zentrum für Materialien und Energie GmbH Glienicker Str. 100, D-14109 Berlin, Germany

Institute for MaterialsChair of Materials Technology, Ruhr-Universitaet Bochum, Universitaetsstr. 150, IA 2/152, Bochum, D-44801, Germany

References (22)

Show source-provided references
1. Zum Gahr K.H. ‘Microstructure and wear of materials’, Tribology series, vol. 10; 1987, Amsterdam, Elsevier.
2. 10.1016/S0043-1648(02)00300-910.1016/S0043-1648(02)00300-9 ↗
3. 10.1515/htm-2000-55011510.1515/htm-2000-550115 ↗
4. 10.1016/S0043-1648(01)00630-510.1016/S0043-1648(01)00630-5 ↗
5. Theisen W. ‘The use of tool steels: experience and research (Proc. 6th Int. Tooling Confi)’, (ed.Bergstrom J. et al.),Vol. 1; 2002, Motala, Motala Grafiska AB.
6. Theisen W. · Proc. Powder Metallurgy World Cong. & Exhibit., Vienna, Austria, October 2004, EPMA, · 797
7. Theisen W., and Broeckmann C.: Proc. 6th Int. Tribol. Conf. (ed.Stachowiak G. W.), Perth, Australia, December 2002,375–381.
8. 10.1179/174329006X12835910.1179/174329006X128359 ↗
9. 10.1002/adem.20060025710.1002/adem.200600257 ↗
10. 10.1002/mawe.20070015510.1002/mawe.200700155 ↗
11. Weber S. ‘Gezielte Ausnutzung des Stofftransportes zur Herstellung neuartiger PM-Hartverbundwerkstoffe auf Eisenbasis’, PhD thesis, Ruhr-Universität Bochum, Institut fiir Werkstoffe, 2005.
12. German M. R. · Int. J. Powder Metall · 1990 · 26 · 23
13. German M. R. · Int. J. Powder Metall · 1990 · 26 · 33
14. 10.1007/s11661-997-0217-010.1007/s11661-997-0217-0 ↗
15. 10.1016/S0026-0657(99)80824-810.1016/S0026-0657(99)80824-8 ↗
16. Talacchia S., Amador J., Urcola J., and Reinstadler R.: Met. Powder Rep. 1995, 16–20.
17. Aguirre I., Giménez S., Talacchia S., Gömez-Acebo T., and Iturriza I.: Powder Metall. 1999, 42, (4), 353–357.10.1179/003258999665701 ↗
18. Talacchia S., San Martin I. J., Urrutibeaskao I., Jauregi S., Palma R., Martinez V., and Urcola J.: Powder Metall. 1993, 36, (4), 275–280.10.1179/pom.1993.36.4.275 ↗
19. Giménez S., Zubizarreta C., Trabadelo V., and Iturriza I.: Mater. Sci. Eng. A, 2008, A480, (1-2),130–137.10.1016/j.msea.2007.06.082 ↗
20. 10.1016/j.scriptamat.2005.04.01710.1016/j.scriptamat.2005.04.017 ↗
21. 10.1002/mawe.1997028020610.1002/mawe.19970280206 ↗
22. Berns H. ‘Hartlegierungen und Hartverbundwerkstoffe'; 1998, Berlin, Springer.10.1007/978-3-642-51505-7 ↗