journal article·1991-11

Influence of macroscopic residual stress fields on fatigue crack growth measurement in SiC particulate reinforced 8090 aluminium alloy

D. M. Knowles, J. E. King

Materials Science and Technology· Volume 7· Issue 11
Publisher page

Abstract

The effect of residual stresses, induced by cold water quenching, on the morphology of fatigue crack fronts has been investigated in a powder metallurgy 8090 aluminium alloy, with and without reinforcement in the form of 20 wt-%SiC particles. Residual stress measurements reveal that the surface compressive stresses developed in these materials are significantly greater than in conventional metallurgy ingot 8090, because surface yielding occurs on quenching. The yield stresses of the powder route materials are greater than those of ingot produced 8090 and hence greater surface stresses can be maintained. In fatigue, severe crack front bowing is observed in the powder formed materials as a result of the reduction of the R ratio (minimum load/maximum load) by the compressive residual stresses at the sides of the specimen, causing premature crack closure and hence reducing the local driving force for fatigue crack growth ∆K eff . This distortion of the crack fronts introduces large errors into measurements of crack growth rate and threshold values of ∆K. MST/1370
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Fatigue and fracture mechanics · Aluminum Alloy Microstructure Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (20)

Show source-provided references
1. NAIR S. V., , TEIN J. K., , and BATES R. C.: int. Met. Rev., 1985, 30, (7), 275–290.
2. 10.1016/0025-5416(84)90101-010.1016/0025-5416(84)90101-0 ↗
3. 10.1016/0013-7944(86)90246-810.1016/0013-7944(86)90246-8 ↗
4. WHITE J. HUGHES I. R. WILLIS T. C. and JORDAN R. M.: J. Phys. 1987 48-C3 Suppl 9 347-353.10.1051/jphyscol:1987340 ↗
5. 10.1007/BF0264708310.1007/BF02647083 ↗
6. 10.1016/0025-5416(88)90573-310.1016/0025-5416(88)90573-3 ↗
7. Annual ASTM Book of Standards Vol. 3.01 E837-89; 1989 New York ASTM.
8. 10.1111/j.1475-1305.1976.tb00194.x10.1111/j.1475-1305.1976.tb00194.x ↗
9. ‘Measurement of residual stresses by the hole-drilling strain gauge method’ Technical Note TN- 505-3 Raleigh Measurements Group Inc.
10. JEANMART P., and BOUVAIST J.: Mater, Sci. Technol., 1985, 1, 765–769.
11. NICKOLA W. E.: in STP 993 ‘Mechanical relaxation of residual stresses’ (ed. Mordfin L. 7-18; 1988 Philadelphia PA ASTM.10.1520/STP26356S ↗
12. ‘Metals handbook’ 9 edn Vol. 7 ‘Powder metallurgy’ 724; 1984 Metals Park OH ASM.
13. NEWBERY R.: personal communication BP Research Centre Sunbury-on-Thames 1990.
14. NEWBERY R.: personal communication BP Research Centre Sunbury-on-Thames 1990.
15. FLETCHER A. J. GEARY W. and KING J. E.: ifl STP 1004 ‘Analytical and experimental methods for residual stress effects in fatigue’ (ed. Champoux R. L. et al.) 82–96; 1988 Philadelphia PA ASTM.10.1520/STP17174S ↗
16. Annual ASTM Book of Standards Vol. 3.01 487-511; 1989 New York ASTM.
17. GREEN A. M.: PhD thesis University of Cambridge 1990.
18. WHITE J. MILLER W. S. PALMER I. G. DAVIS R. and SAINI T. S.: in Aluminium—lithium alloys III’ (ed. C. Baker etal.) 530-538; 1985 London The Institute of Metals.
19. 10.1115/1.322498810.1115/1.3224988 ↗
20. 10.1007/BF0232682510.1007/BF02326825 ↗